Instructions / Assembly
MA086 • 09/01/20
1.888.830.1326
Improper installation could cause the light xture to fall, or
result in electrical shock or personal injury.
Using the provided wire connectors connect the
white wire from the fan to the white wire from the
wire harness and connect the black or blue wire from
the fan to the black wire from the wire harness.
Wire
Connector
Switch
Housing
Read entire
installation
instructions carefully
before beginning
installation and save
these instructions.
START
HERE
4 Light
Accessory Fitter
Models 99384, 99385, 99386, 99387
OF
OF
F
F
Turn Power
Using the single pin connectors,
connect the black or blue wire from the
fan to the black wire from the light kit.
Connect the white wire from the fan to
the white wire from the light kit.
Align the
notches in the sides of the light kit assembly
with the screws on the upper
switch housing. Twist the light kit assembly
clockwise to lock into place.
Install the nal light kit screws in the remaining
holes. Tighten all four screws securely.
Light Kit
Screw
Remove the switchousing cap screws with a
Phillips head screwdriver. Remove the insulator
and set aside. You will need this again for
installing the light kit.
Switch
Housing
Cap
Cap
Screw
Insert the insulator back into the switch
housing while passing the wires from the fan
through the center hole. Lift the cap ring and
align the holes with the switch housing screw
holes. Attach cap ring to switch housing with
switch housing screws.
Preinstall two light kit screws into the cap ring
using any two opposing holes. It does not matter
which two you choose.
Cap Ring
Switch
Housing
Screw
Do not allow the light kit to hang only by
the wire connections!
Light kit style may vary.
To install the shade, rst loosen the thumb
screws. Raise the shade to the light xture.
Tighten all thumbscrews securely.
Install a bulb into each of the sockets. When
necessary, replace with bulbs of same wattage.
Typical Harness
white
blue or
black
white
Black
READ AND SAVE THESE
INSTRUCTIONS
This product conforms to UL Standard 507.
CAUTIONS
c.1 - To reduce the risk of electric shock, disconnect the
electrical supply circuit to the fan before installing the
light kit.
c.2 - To reduce the risk of re and electric shock, this
light kit should be used only with the fan models listed
above.
c.3 - All wiring must be in accordance with national
and local electrical codes ANSI/NFPA 70. If you are
unfamiliar with wiring, use a qualied electrician.
Weight ±2 lbs: 4.8 lbs (2.2 kg)
Installing the Pull chain pendant - Attach
the pull chain pendant to the end of the short
chains coming from the light kit.
ON
ON
Turn Power
ONE YEAR WARRANTY
This product is warranted to the original
purchaser by Hunter Fan Company against
defects in material and workmanship for
one (1) year from date of purchase. During
the warranty period, we will repair or, at
our option, replace a defective product
at no charge. For information on how to
obtain service, contact the Hunter Service
Department by calling our toll-free number
at 888-830-1326. Damage to the product
caused by mishandling, improper installation
or modication is not covered by this
warranty. This warranty is given in lieu of
all other warranties expressed or implied.
Some states do not allow limitations of time
on an implied warranty, therefore the above
limitations may not apply in every case. This
warranty states specic legal rights which
may vary from state to state.
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify
that the light and power wires are correctly connected to the
ceiling and the light kit.
If you have problems installing or operating your light kit, do not return
this product to the dealer. Call our Consumer Affairs Hotline.
888-830-1326