Wet-Rated Globe Fitter Installation Manual Models 99168, 99169, 99170 Compatible with: 2xxxx Types A - Z 51000-58999 fan series 59500-59999 fan series Select Casablanca Fans MA019-01 • 02/05/14
1.888.830.1326 BEFORE YOU BEGIN Read entire installation instructions carefully before beginning installation and save these instructions. Switch Housing Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s switch housing. Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan. From there, you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan.
1.888.830.1326 WHICH ASSEMBLY METHOD WILL I USE? Choose one of the four images below that most closely resembles the switch housing on your fan; then follow the instructions under the image. Cap Screw Switch Housing Screw Switch Housing Cap If your fan’s switch housing cap resembles this one, remove the cap screws with a Phillips head screwdriver. Then follow the TYPE-A ASSEMBLY INSTRUCTIONS on pages 4-5.
1.888.830.1326 TYPE-A ASSEMBLY INSTRUCTIONS 1 2 Switch Housing Wire Connector Mounting Screw If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness. Feed the wires through the center hole in the gasket.
1.888.830.1326 TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Thumbscrews Bulb Installing the globe (sold separately)To install the globe, first loosen the thumbscrews. Raise the globe to the light fixture. Tighten all thumbscrews securely. Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. 7 8 er ow P n Tur ON Installing the pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
1.888.830.1326 TYPE-B ASSEMBLY INSTRUCTIONS 1 2 Switch Housing Feed the wires through the center hole in the switch housing, the washer, and the nut. Push the center hole in the gasket over the threaded rod of the light kit. Then install the switch housing by twisting clockwise onto the threaded rod. Install the washer and nut onto threaded rod and tighten securely.
1.888.830.1326 TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Thumbscrews Bulb Installing the globe (sold separately)To install the globe, first loosen the thumbscrews. Raise the globe to the light fixture. Tighten all thumbscrews securely. Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. 7 8 er ow P n Tur ON Installing the pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
1.888.830.1326 TYPE-C ASSEMBLY INSTRUCTIONS 1 2 Switch Housing Wire Connector If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness. Feed the wires through the center hole in the gasket and switch housing.
1.888.830.1326 TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Thumbscrews Bulb Installing the globe (sold separately)To install the globe, first loosen the thumbscrews. Raise the globe to the light fixture. Tighten all thumbscrews securely. Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. 7 8 er ow P rn Tu Installing the pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
1.888.830.1326 TROUBLESHOOTING Lights don’t come on. • Make sure that the bulbs are properly installed. • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Check the circuit breaker to ensure the power is turned on. • Check the pin connections in the light kit. • Refer to the fan manual for locating the fan’s wiring. Verify that the light and power wires are correctly connected to the ceiling and the light kit.
