programmable control model 99107 installation and setup guide M3561-01 • 01/26/15 • ©2014 Hunter Fan Company
installation Prior to installation, download the app to ensure phone compatibility: Visit your app store and search simpleconnect to find the app. 1 If your fan has pull chains, use the pull chains to set the fan speed to HIGH and the light to ON before disconnecting power. 2 Ensure that power is OFF at the circuit breaker before proceeding with installation. Turn Power OFF 3 Unscrew and lower the canopy.
installation (continued) 4 Choose the hanging system that most closely resembles the one used by your fan and place the receiver as shown. WARNING: This receiver cannot be installed in conjunction with any other receiver or hard-wired wall control. Doing so will void your warranty. Hanging System 1 Hanging System 2 Receiver Receiver Canopy Canopy Hanging System 3 Hanging System 4 For low profile fans, secure the receiver to the ceiling bracket with a cable tie.
installation (continued) 5 Connect wires from the receiver to wires from the fan as shown. M RO • Connect the blue wire from the receiver to the light wire (blue or possibly black with white stripe) from the fan. • Connect the yellow wire from the receiver to the motor wire (black) from the fan. RECEIV M FAN FRO E R F Using the wire connectors: blue blue (or black/white stripe) yellow black Note: If you’re uncertain about wire colors or connections, please contact a qualified electrician.
installation (continued) 6 Connect wires from the fan and receiver to wires from the ceiling as shown. Using the wire connectors: • Connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. • Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan. M RO RECEIV E R F Note: If you have a dual switch, please cap the secondary power wire from the ceiling. This will result in one unused switch.
setup If you have not downloaded the app, do so now. Visit your app store and search simpleconnect. Install. 1 Record PIN. Write down the PIN located on the Bluetooth® plug-in controller. You will need the PIN to complete step 5. PIN: 2 Plug in the Bluetooth® Plug-in Controller. The Bluetooth® plug-in controller works up to 80 feet from the fan/receiver. 3 Launch the app. 4 Tap the Controller button. 5 Enter the PIN. Ensure that Bluetooth® is enabled on your device before launching the app.
setup for additional fans using a single Bluetooth® plug-in controller If you wish to operate multiple fans with one Bluetooth® plug-in controller: 1. You will need an additional receiver (sold separately) for each fan. Complete the Installation section to install each receiver into your fan(s). Receivers can be purchased at www.HunterFan.com. 2. Tap the Gear icon on the main screen to navigate to the “Rooms Configured” settings screen. 3. Perform steps a-d on this page to complete setup.
optional ON/OFF remote maintenance Installing/Replacing the Battery To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Battery Door Replace with a CR2032 battery when necessary. Phillips Head Screw pairing No Pairing Required! The optional ON/OFF remote is already paired to the receiver and ready to use.
troubleshooting CFL Bulbs Flicker Tap the Gear icon in the Room setup screen to visit the settings screen for the appropriate room or fan. If Dimming Mode is on, turn off Dimming Mode. If the problem is not corrected, unpair and re-pair the device with Dimming Mode disabled. Fan will not start • Make sure the power is on at the circuit breaker and the wall switch. • Make sure that the transmitter and receiver are paired. • Check wire connections inside of the canopy.
HUNTER FAN COMPANY CONTROL - LIMITED WARRANTY The Hunter Fan Company makes the following limited warranty to the original purchaser of the receiver, Bluetooth® controller, and optional ON/OFF remote (collectively, the “Control”): Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale. If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge.
