Copperhill Installation Manual Model: 59638 Brittany Bronze Fan weight ±2 lbs: 24.3 lbs (11.0 kg) ©2018 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Wood Screw Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: Do this first! The machine screws are the ones that came with your outlet box.
1886 Installing the Downrod WARNING • ALWAYS tighten setscrew with pliers. & STEP 8” • DO NOT hand tighten setscrew. • CHECK the setscrew is tight using pliers each time you change fan direction. (not to scale) STEP To prevent SERIOUS INJURY or DEATH: STRIP 2 3/8” 1 FAN FALL HAZARD The ground wire attached to the downrod is approximately 8 inches. CUT STEP Follow below if you are using the downrod that came pre-assembled in your box.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. Then install the blade screws to secure each blade to a blade iron.
1886 Preparing the Light Fixture Follow these steps to prepare the light fixture for installation. KEEP Fixture Screw Red Flag Remove the pre-installed fixture screw and red flag from the light kit assembly. Save the screw. It will be needed for light kit installation. Loosen the other three fixture screws, but do NOT remove completely. Note: The screw was installed for shipping purposes only. Remove and discard the plastic connectors from the ends of the two pull chains.
1886 Installing the Light Fixture Keyhole Slot Align the three keyhole slots in the light kit with the three assembly screws in the posts. Lift the light kit and twist counterclockwise to lock it into place. Be sure that both pull chains are hanging freely. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors and that the connectors latch. This is a screw you saved that was attached to the red flag.
1886 Installing the Pull Chains The fan pull chain controls the speed: from high to off. Feed the pull chains from the fan switch and the light switch down through the holes in the upper switch housing as shown. Attach the pull chain pendants to the light and fan pull chains. The light pull chain controls the light fixture: on and off.
1886 Reversing the Fan Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. The reversing switch is located inside the light fixture cage. It can only be accessed when the cage is removed. Slide the reversing switch to the opposite position. Restart the fan. Updraft (counterclockwise rotation) creates a more indirect airflow.
1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe 1 10 2 3 9 4 8 5 7 6 Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly. • VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
1886 Troubleshooting Fan Doesn’t Work Excessive Wobbling • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades are properly installed on the blade iron posts. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
