Oceana Installation Manual Model: 59615 Noble Bronze 59616 Matte Silver Fan weight ±2 lbs: 21.2 lbs (9.6 kg) ©2019 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. 1886 Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: Option 2: Wood Screws The machine screws are the ones that came with your outlet box. Use wood screws (included) when securing to support structure with approved electrical outlet box.
1886 Installing the Downrod Follow below if you are using the downrod that came pre-assembled in your box. Need to install a longer or shorter downrod? Check out the guide at the end of this manual. 1 STEP STEP STEP Hunter Pro Tip: 2 3 The ground wire attached to the downrod is approximately 8 inches. ! KEEP Slide the adapter cover onto the downrod until it rests against the hanger ball. Remove the pre-installed setscrew so that the downrod can be inserted.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. Slide the remote receiver onto the top of the bracket. WARNING WARNING Hunter Pro Tip: Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Insert the blade into the blade slot around the center screw. Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to the fan.
1886 Assembling the Light 2 of 3 bag Light Kit Screw Feed the 9-pin plug connector coming from the bottom of the motor housing through the center hole in the light kit assembly. Connect it to the plug connector found in the switch housing area of the light kit assembly. Make sure to line up the colored markings on the connectors. Partially install two light kit screws, found in the hardware bag, through the gasket halfway into the motor housing as shown.
1886 Preparing the Wall Control 1 Turning off the power KEY PRESS Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. LIGHT FUNCTIONS n Tur 2 Installing the battery To access the battery compartment, slide the battery door up. FUNCTION er Pow Light On/Off OFF Light Dimming Control Long Press Long Press Battery Door Long Press Replace the used battery with two AAA batteries when needed.
1886 Reversing the Fan Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. Slide the reversing switch to the opposite position. Restart the fan. Updraft (clockwise rotation) creates a more indirect airflow. Updraft airflow is great for moving warm air downward.
1886 Limited Lifetime Warranty Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com. Thank you for choosing Hunter! How Can Warranty Service Be Obtained? Proof of purchase is required when requesting warranty service. The original purchaser must present a sales receipt or other document that establishes proof of purchase. Hunter, at its sole discretion, may accept a gift receipt.
