Lantern Bay Installation Manual Model: 59581 Matte Black 59582 Onyx Bengal Fan weight ±2 lbs: 26.5 lbs (12 kg) ©2018 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. x2 Wood Screw Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
1886 Hanging the Fan S li d e c a n o p y ove rd NOTICE o wn ro d an d To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. w i re s . DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Progress Check: Your fan should look like this.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. Hunter Pro Tip: Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 Canopy Screw bag op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. Then install the blade screws to secure each blade to a blade iron.
1886 Preparing the Light Fixture Follow these steps to prepare the light fixture for installation. x1 KEEP Fixture Screw Red Flag Carefully remove the light fixture from the light fixture hood and set the light fixture. Remove the pre-installed fixture screw and red flag from the light kit assembly. Save the screw. It will be needed for light kit installation. Note: The screw was installed for shipping purposes only.
1886 Installing the Light Fixture 3 of 6 bag Fixture Screw Fixture Screw Empty Post Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors and that the connectors latch. Partially install three fixture screws, found in the hardware bag, into the posts as shown, leaving the circled post empty. Align the three keyhole slots in the light kit with the three assembly screws in the posts.
1886 Installing the Glass and Light Fixture Cage Fixture Screws 2 of 6 bag Fixture Screw Fixture Screws Partially install two fixture screws, found in the hardware bag, halfway into the light fixture as shown. It does not matter which two screw holes you choose. Carefully lower the glass into the light fixture cage until it rests in place. 1 of 6 bag Fixture Screw Fixture Screw Align the keyhole slots in the cage with the partially installed screws in the light fixture.
1886 Preparing the Remote To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. Battery Door r we Po n r Tu ON Phillips Head Screw Installing the Remote Control Cradle You have two options for installing the remote cradle. Choose which path works best for you.
1886 Troubleshooting Fan Doesn’t Work Remote Only Works Close to Fan • Make sure power switch is on. • • Push the motor reversing switch firmly left or right to ensure that it is engaged. Change battery. Noisy Operation • Check the circuit breaker to ensure the power is turned on. • Make sure the blades are properly installed. • Make sure the blades spin freely. • Check to see if any of the blades are cracked. If so, replace all of the blades.
1886 Limited Lifetime Warranty Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com. Thank you for choosing Hunter! How Can Warranty Service Be Obtained? Proof of purchase is required when requesting warranty service. The original purchaser must present a sales receipt or other document that establishes proof of purchase. Hunter, at its sole discretion, may accept a gift receipt.
