Advocate Collection Installation Manual Model: 59365 Fresh White 59366 Noble Bronze 59367 Matte Nickel Fan weight ±2 lbs: 19 lbs (8.6 kg) ©2017 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Wood Screw Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box. Do this first! er ow P n r Tu OFF x2 Washer Option 2: Wood Screws Option 1: Machine Screws Use wood screws and washers (included) when securing to support structure with approved electrical outlet box.
1886 STEP STEP Installing the Downrod 4 5 Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. Lower the adapter cover until it rests flush against the motor housing. WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers. • DO NOT hand tighten setscrew. • CHECK the setscrew is tight using pliers each time you change fan direction.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws hardware bag. found in the x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Insert the blade into the blade slot. Repeat x4 Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to the fan.
1886 Assembling the Light Kit 2 of 5 Light Kit Screw bag Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose. 2 of 2 3 of 5 bag Light Kit Screw bag Align the keyhole slots in the top of the light kit assembly with the partially installed assembly screws. Wrap the keyhole slots around the screws and twist counterclockwise. Install the third screw. Tighten all three screws securely.
1886 Installing the Remote Control Cradle You have two options for installing the remote cradle. Choose which path works best for you. Option 1: Using Adhesive Strip Option 2: Using Screws Remove the cradle from the cradle bracket. Separate the lining from the back of the adhesive strip on the cradle bracket. Press the cradle bracket against the wall and hold firmly for 30 seconds. If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide.
1886 Troubleshooting Fan Doesn’t Work Remote Only Works Close to Fan • Make sure power switch is on. • • Pull the pull chain to make sure it is on. Noisy Operation • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Make sure the blades are properly installed. • Check the circuit breaker to ensure the power is turned on. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Make sure the blades spin freely.
1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe 1 10 2 3 9 4 8 5 7 6 Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly. • VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
