www.HunterFan.com Table of Contents Tools Needed Mounting Options Ceiling Bracket 30 inches Downrod 3 Wiring To register your fan, please visit: www.HunterFan.com/register PA G E Maintenance & Cleaning Light Kit ? 16 ? ? 17 PA G E 1 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company 12 Troubleshooting PA G E PA G E PA G E 15 5 Blades 11 PA G E Switch Housing 13 Canopy 9 PA G E 6 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Note: Fan style may vary. 8 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring: Single Switch www.HunterFan.com 1.888.830.1326 Dual Switch Instructions Have a single switch? Follow these steps: gro Un Grounded White ou nd ing i pe Str Gr Blue Connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. ellow Green/Y Connect the white (grounded) wire from the ceiling to the white wire from the fan.
Wiring: Dual Switch www.HunterFan.com 1.888.830.1326 Have dual switches? Follow these steps: Grounded ellow Green/Y Grounded White Gr ou Ungrounded (lig ht) Black ing rou nd ed Green/Yellow Stripe Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. Un g Connect the black wire (ungrounded) from the ceiling to the black wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 12 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company 1.888.830.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Note: Remove the three pre-installed screws from the switch housing and save the screws. You will need them later. 1.888.830.
www.HunterFan.com Switch Housing (continued) Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Align the the screw holes in the upper switch housing posts with the holes in the lower switch housing. Raise the switch housing to the upper switchhousing 14 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company 1.888.830.1326 Install the three switch housing screws. Tighten all three screws securely.
www.HunterFan.com Light Kit Light Pull Chain 1.888.830.1326 Fan Pull Chain CONGRA T YOU’REULATIONS! DONE! Lift the shade and attach it to the upper switch housing using the three thumbscrews. Tighten all three screws securely by hand. Connect the appropriate pull chain pendant to each of the short chains coming from the light kit. The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. Note: Fan style may vary.
Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 r we o nP r Tu ON Reverse Switch Changing the bulb - Unscrew the bulb and replace with a bulb of same type and wattage. Changing the direction of air flow - move the reverse switch to the opposite position. 16 M3624-01 • 10/11/16 • © 2016 Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
