Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 76.2 cm / 30 in.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step. If mounting to a support structure, you will also need these tools.
34O CEILING Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Option 1 Downrod 1.888.830.1326 skip to next page Standard Downrod for ceilings 2.4–3 m / 8–10 ft. high Steps 1–5 to remove standard downrod pipe 1 2 4 Sold Separately Slide 3 10 9 5 Slide Option 3 Longer Downrod for angled ceilings or ceilings 3 m / 10 ft.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) (not to scale) 20 cm 88in. in. & .95 cm 3/8 3/8in. in. 1.888.830.1326 STRIP CUT Downrod (continued) KEEP! ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4–5 full turns) until it stops. The wires can be cut, but leave at least 20 cm / 8 in. extending from the top of the downrod. Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. .95 cm 3/8 in.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 1.888.830.1326 DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M3639-01 • 12/19/16 • © 2016 Hunter Fan Company www.HunterFan.
Wiring Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. OM CEILING FR green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Receiver 1.888.830.1326 Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) OM FR RECEIV ER • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. OM FAN FR white white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver. black • blue Connect the yellow wire from the receiver to the black wire from the fan. black • 1.888.830.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Canopy 1.888.830.1326 Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 11 M3639-01 • 12/19/16 • © 2016 Hunter Fan Company www.HunterFan.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Blades 1.888.830.1326 Attach each blade to a blade iron using three blade washers, found in the hardware bag, and three blade assembly screws, found in the hardware bag. 12 M3639-01 • 12/19/16 • © 2016 Hunter Fan Company www.HunterFan.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Light Kit 1.888.830.1326 Note: Remove the pre-installed light kit assembly screw and red flag from the light kit assembly. Save the screw. It will be needed for installation Screw two housing assembly screws from the hardware bag halfway into the upper switch housing. It does not matter which two screw holes you choose. Connect the plugs from the upper and lower switch housings.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Light Kit (continued) 1.888.830.1326 Tab Notch Bulb CONGRA YOU’RETULATIONS! DONE! Install a light bulb in each socket. When necessary, replace with bulbs of the same wattage. Position the notches in the outer rim of the globe so they line up with the tabs on the inside surface of the light fixture rim. Carefully lift the globe up inside the light fixture as far as it will go.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Remote & Cradle 1.888.830.1326 CAUTION: • Always purchase the correct size and grade of battery most suitable for the intended use. • Replace all batteries of a set at the same time. • Clean the battery contacts and also those of the device prior to battery installation. • Ensure the batteries are installed correctly with regard to polarity (+ and -).
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Remote & Cradle (continued) 1.888.830.1326 Light On/Off Fan On/Off Fan Speed Up Fan Speed Down The remote transmitter is already paired to the receiver and ready to use. Note: If your need to pair your remote, turn fan power off and back on at the wall switch. Within 3 minutes, press and hold both the Fan Off button and the High button for 4 seconds to pair the remote.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Remote & Cradle (continued) 1.888.830.1326 You have two options to install the included remote control cradle to the wall. Choose which path works best for you. Option 1: Using Screws Option 2: Using Adhesive Strip Choose your cradle installation location. Remove the cradle from the cradle bracket. If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Operation, Maintenance, & Cleaning 1.888.830.1326 Reverse Switch Slide the remote into the cradle when not in use. To switch the direction of air flow, move the reverse switch to the opposite position. You will need to remove the light kit glass to do so. 19 M3639-01 • 12/19/16 • © 2016 Hunter Fan Company For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. www.
Monday - Friday 8am - 6pm CST Saturday 11am - 4pm CST (English or Español) Troubleshooting Fan doesn’t work Excessive wobbling Noisy operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on.
