www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3556-01 • 06/17/14 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Motor Housing Gently lower the motor housing so it rests in place on the motor assembly. www.HunterFan.com Align the screw holes in the top of the motor housing with the screw holes in the motor assembly. Install the three motor housing screws, found in the hardware bag. 6 M3556-01 • 06/17/14 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3556-01 • 06/17/14 • © Hunter Fan Company 1.888.830.
Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3556-01 • 06/17/14 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Place each blade between a blade iron and medallion. Install three blade screws, found in the hardware bag, to attach the medallion to the blade iron. 1.888.830.1326 Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching.
Switch Housing & Light Kit www.HunterFan.com 1.888.830.1326 Red Flag Remove the pre-installed light kit assembly screw and red flag from the light kit assembly. Save the screw. It will be needed for light kit installation. Remove and discard the plastic connectors from the ends of the two pull chains. Note: The screw was installed for shipping purposes only. 13 M3556-01 • 06/17/14 • © Hunter Fan Company Carefully remove the light kit from the upper switch housing and set the light kit aside.
Switch Housing & Light Kit (continued) www.HunterFan.com 1.888.830.1326 Switch Housing Assembly Screw Partially install two switch housing assembly screws ,found in the hardware bag, into the motor housing as shown. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the two screws and twist counterclockwise to lock the upper switch housing into place.
www.HunterFan.com Switch Housing & Light Kit (continued) 1.888.830.1326 Empty Post Keyhole Slot Light Kit Assembly Screw Partially install three light kit assembly screws, found in the hardware bag, into the posts as shown, leaving the circled post empty. Use only the light kit supplied with this fan model. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors.
www.HunterFan.com Switch Housing & Light Kit (continued) Remember the screw you kept after removing the red flag (page 13)? You need it for this step. Install the fourth light kit assembly screw and tighten all four screws securely. Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. 16 M3556-01 • 06/17/14 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Globe 1.888.830.1326 Globe Assembly Screws Feed the pull chains from the fan switch and the light switch down through the holes in the upper switch housing as shown. Attach the pull chain pendants to the light and fan pull chains. The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. Partially install two globe assembly screws, found in the hardware bag, halfway into the light kit assembly as shown.
www.HunterFan.com Globe (continued) CONGRA T YOU’REULATIONS! DONE! Align the keyhole slots in the globe assembly with the partially installed screws in the light kit assembly. Lift the globe assembly and twist counterclockwise to lock it into place. Make sure the globe assembly is securely attached to the switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Install the third globe assembly screw and tighten all three screws securely.
Maintenance & Cleaning www.HunterFan.com r we o nP 1.888.830.1326 Reverse Switch r Tu ON Changing the bulbs - carefully remove the globe assembly. Unscrew the bulbs and replace with bulbs of the same wattage. Reinstall the globe assembly. Changing the direction of air flow - move the reverse switch to the opposite position. Note: The reversing switch is located on the switch housing. It can only be accessed when globe is removed.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
