www.HunterFan.com Table of Contents Tools Needed Mounting Options Ceiling Bracket 30 inches To register your fan, please visit: www.HunterFan.com/register Wiring 12 Troubleshooting ? ? ? 17 PA G E 16 PA G E 1 M3531-01 • 06/05/13 • © Hunter Fan Company 15 11 Operation, Maintenance & Cleaning PA G E PA G E 14 5 Light Kit PA G E Remote Control PA G E Globe 4 Canopy 10 PA G E 6 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3531-01 • 06/05/13 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Ceiling Bracket www.HunterFan.com 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com 1.888.830.
www.HunterFan.com Downrod (continued) 1.888.830.1326 Hanger Ball ! KEEP Adapter Cover Slide the adapter cover onto the downrod until it rests against the hanger ball. Remove the pre-installed setscrew so that the downrod can be inserted. 7 M3531-01 • 06/05/13 • © Hunter Fan Company Hand tighten the downrod (at least 4-5 full turns) until it stops.
www.HunterFan.com (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) The wires can be cut, but leave at least 8” extending from the top of the downrod. Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3531-01 • 06/05/13 • © Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. CEILIN G OM FR T KE black (live in) FR black (ungrounded) M FA N white (neutral in) FRO Using an orange wire connector from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”).
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3531-01 • 06/05/13 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Light Kit To attach the light kit top housing, partially install two housing assembly screws, found in the hardware bag, into the light kit mounting plate. Align the keyhole slots in the housing with the housing assembly screws. Use only the light fixture supplied with this fan model. 12 M3531-01 • 06/05/13 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Screw Holes Connect the upper plug connector from the motor to the lower plug connector in the light kit. Turn the light kit top housing counterclockwise until the housing assembly screws are firmly situated in the narrow ends of the keyhole slots. Install the remaining screw into the housing. Tighten all three screws firmly. Note: Both plug connectors are polarized and will only fit together one way.
www.HunterFan.com Globe 1.888.830.1326 CONGRA YOU’RETULATIONS! DONE! Lift the globe up to the light kit top housing. Align the three bolts on the globe with the three slots in the light kit top housing. Rotate the globe clockwise until tight. See next page for fan operation instructions.
Remote Control www.HunterFan.com 1.888.830.1326 High Medium Low Fan Off Battery Door Light High Fan Off Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. Turn Power ON Note: The remote must be paired before the fan will operate.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim. After a total of 30 seconds, the lights will be completely off.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy operation • Make sure power switch is on. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
