www.HunterFan.com Table of Contents Tools Needed Mounting Options Ceiling Bracket 30 inches To register your fan, please visit: www.HunterFan.com/register 4 Wiring Canopy Operation, Maintenance & Cleaning Light Kit Troubleshooting ? ? 15 PA G E 1 M3648-01 • 03/27/17 • © Hunter Fan Company 13 PA G E PA G E 11 9 ? 5 10 Blades PA G E 7 PA G E PA G E 6 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3648-01 • 03/27/17 • © Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com (not to scale) 8” & 3/8” STRIP CUT Downrod The wires can be cut, but leave at least 8” extending from the top of the downrod. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8” 3/8” 6 M3648-01 • 03/27/17 • © Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. 1.888.830.1326 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) www.HunterFan.com OM FR OM CEILING FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 9 M3648-01 • 03/27/17 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Insert a blade into the motor housing. Attach each blade to the fan using two blade grommets, found in the hardware bag, and two blade assembly screws, found in the hardware bag. 10 M3648-01 • 03/27/17 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Light Kit 1.888.830.1326 Light Kit Assembly Screw Partially install two of the light kit assembly screws, found in the hardware bag. Align the keyholes in the light kit ring with the partially installed screws. Lift the light kit ring in place and rotate counterclockwise to situate the screws in the narrow ends of the keyholes. 11 M3648-01 • 03/27/17 • © Hunter Fan Company Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Tab CONGRA YOU’RETULATIONS! DONE! Notch Install the included LED bulbs. When necessary, replace with bulbs of same wattage. Position the notches in the outer rim of the globe so they line up with the tabs on the light kit ring. Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs.
Operation, Maintenance, & Cleaning www.HunterFan.com Fan Off 1.888.830.1326 Medium Speed High Speed Switch Cover Plate Battery Door Low Speed Light Phillips Head Screw Removed Tabs To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com Reverse Switch To switch the direction of air flow, move the reverse switch to the opposite position. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 14 M3648-01 • 03/27/17 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Use the provided balancing kit and instructions to balance the fan. • Make sure the blades spin freely.
