Table of Contents 1.888.830.1326 Ceiling Bracket 30 inches Ladder Downrod 3 Wiring 10 Operation, Maintenance & Cleaning Light Kit 11 Troubleshooting ? ? ? 17 PA G E 15 PA G E 1 M3519-01 • 05/14/14 • © Hunter Fan Company PA G E PA G E 13 5 Blades PA G E 9 Switch Housing 12 Canopy PA G E 6 4 PA G E 2 PA G E 7 feet PA G E Save your receipt for proof of purchase. Mounting Options PA G E To register your fan, please visit: www.HunterFan.
What to Expect with Your Installation www.HunterFan.com 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
Tools Needed Ladder www.HunterFan.com Pliers Wire Strippers 1.888.830.1326 Screwdrivers If you are installing multiple remote-controlled fans on the same circuit breaker, you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls. Allen Wrench (included) 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3519-01 • 05/14/14 • © Hunter Fan Company Go to www.HunterFan.
34O CEILING Mounting Options (continued) Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.830.
Ceiling Bracket www.HunterFan.com 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com Downrod (continued) 1.888.830.1326 Using the provided Allen wrench, loosen the setscrew on the adapter to install the pipe and ball assembly. (not to scale) 8” & 3/8” STRIP CUT Note: The adapter cover is not used for low-profile mounting. The wires can be cut, but leave at least 8” extending from the top of the downrod. Insert the downrod through the adapter cover. Hand tighten the downrod (at least 4-5 full turns) until it stops.
Downrod (continued) Install the adapter cover screws and tighten them securely. www.HunterFan.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 8 M3519-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. OM CEILING FR T KE AC FRO white FR M FA N OM FAN FR OM white ING BR white (grounded) Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
Canopy www.HunterFan.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 10 M3519-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com 1.888.830.1326 Attach each blade to a blade iron using four blade washers, found in the hardware bag, and four blade assembly screws, found in the hardware bag. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 12 M3519-01 • 05/14/14 • © Hunter Fan Company 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
Light Kit www.HunterFan.com 1.888.830.1326 Switch Housing Screw Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag. Align the keyhole slots in the light kit housing with the housing assembly screws.
Light Kit (continued) www.HunterFan.com 1.888.830.1326 Tab Notch Bulb Install the 18-Watt dimmable CFL bulb into the socket. When necessary, replace with bulbs of same wattage. CONGRA YOU’RETULATIONS! DONE! Align the notches in the glass bowl with the tabs in the light kit. Attach the glass bowl to the light kit by twisting it clockwise until it snaps into place. 14 M3519-01 • 05/14/14 • © Hunter Fan Company See next page for fan operation instructions.
Operation, Maintenance, & Cleaning www.HunterFan.com Fan Off 1.888.830.1326 Medium Speed High Speed Switch Cover Plate Battery Door Low Speed Light Fan Off High Phillips Head Screw Removed Tabs To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
Troubleshooting Fan doesn’t work • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. www.HunterFan.com CFL bulbs flicker or do not dim • Turn the power switch off and back on. Within three minutes, hold down the Fan Off button while pressing the Light button twice. If the problem is not corrected, repeat the process up to three times.
