www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3558-01 • 06/08/16 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Top Housing Upper Motor Cover Screw KEEP! ! KEEP Remove the pre-installed setscrew so the downrod can be inserted. To assemble the housing to the hanger adapter, align the three raised tabs on the hanger adapter with the three narrow notches in the top housing. Make certain the housing sits flat on the adapter. Install three upper motor cover screws, found in the hardware bag, and tighten them securely. 6 M3558-01 • 06/08/16 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com (not to scale) & 3/8” 8” The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 1.888.830.1326 STRIP CUT Downrod (continued) 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3558-01 • 06/08/16 • © Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. 1.888.830.1326 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) www.HunterFan.com OM FR OM CEILING FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 12 M3558-01 • 06/08/16 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Screw Holes Insert the blade into the slot. Align the screw holes in the blade with the screw holes in the motor assembly. Attach the blade to the motor using the flat washers, found in the hardware bag, and blade assembly screws, found in the hardware bag. Repeat for each blade. 13 M3558-01 • 06/08/16 • © Hunter Fan Company 1.888.830.
Light Kit www.HunterFan.com 1.888.830.1326 Light Kit Bracket Screw Partially install two of the light kit bracket screws, found in the hardware bag, into the light kit mounting plate. Thread the 9-pin plug connector from the fan through the light kit. 14 M3558-01 • 06/08/16 • © Hunter Fan Company Align the keyholes in the light kit with the two partially installed screws and turn the light kit clockwise until the screws are in the narrow ends of the keyholes.
www.HunterFan.com Light Kit (continued) Install the third light kit bracket screw, found in the hardware bag. Tighten all three screws securely. Make sure the light kit is securely attached to the mounting plate. Failure to properly secure all three assembly screws could result in the light fixture falling. Connect the upper 9-pin plug connector from the fan to the lower 9-pin plug connector in the light kit. 15 M3558-01 • 06/08/16 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Globe Assembly Screw CONGRA Trim Ring Globe Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. Place the globe into the globe trim ring. Lift the globe assembly and align the screw holes in the trim ring with the screw holes in the light kit and install the three globe assembly screws, found in the hardware bag. Tighten all three screws securely.
www.HunterFan.com Remote Control Battery Door 1.888.830.1326 r we o nP r Tu ON Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. The remote transmitter should already be paired to the receiver and ready to use.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Medium Speed Fan Off Reverse Switch High Speed Switch Cover Plate Low Speed Light Removed Tabs To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on. Rocker- Style Plate To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Use the provided balancing kit and instructions to balance the fan. • Make sure the blades spin freely.
