Table of Contents www.HunterFan.com What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
What to Expect with Your Installation www.HunterFan.com 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
Tools Needed www.HunterFan.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3521-01 • 05/14/14 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (included). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.830.
Ceiling Bracket www.HunterFan.com 1.888.830.1326 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Preparation www.HunterFan.com 1.888.830.1326 A ISC R D D Ceiling Bracket (continued) DISC D AR If you are installing multiple remote-controlled fans on the same circuit breaker, you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls. Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remotecontrolled fans?” for more information. Remove the shipping blocks from the motor. Discard the screws.
www.HunterFan.com 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.HunterFan.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3521-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. OM CEILING FR T KE AC FRO white FR M FA N OM FAN FR OM white ING BR white (grounded) Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
Canopy www.HunterFan.com Screw holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3521-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. Then install the blade screws to secure each blade to a blade iron. 1.888.830.1326 Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise.
Light Kit www.HunterFan.com 1.888.830.1326 Switch Housing Screw Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Note: Globe style and number of lights may vary. Align the keyhole slots in the light kit housing with the housing assembly screws.
Light Kit (continued) www.HunterFan.com 1.888.830.1326 Tab Notch Bulb CONGRA YOU’RETULATIONS! DONE! Install a light bulb in each socket. Note: Do not use CFL bulbs to replace your light bulbs. Your lights may flicker or fail to work. Note: Globe style and number of lights may vary. Lift the globe and align the notches in the globe with the tabs in the light kit. Attach the glass bowl to the light kit by twisting it clockwise until it snaps into place.
Operation, Maintenance, & Cleaning www.HunterFan.com Fan Off 1.888.830.1326 Medium Speed High Speed Switch Cover Plate Battery Door Low Speed Light Fan Off High Phillips Head Screw Removed Tabs To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. Reverse Switch • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
Troubleshooting www.HunterFan.com Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
