www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers Screwdrivers If you are installing multiple remote-controlled fans on the same circuit breaker, you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls. Power Drill (optional) Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remotecontrolled fans?” for more information.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Ceiling Bracket www.HunterFan.com 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Blades www.HunterFan.com Turn the fan motor upside-down and place it in one of the holes in the packaging. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Insert a blade into the motor housing. Attach each blade to the fan using two blade grommets, found in the hardware bag, and two blade assembly screws, found in the hardware bag.
Light Kit To attach the upper switch housing, partially install two switch housing assembly screws, found in the hardware bag, into the switch housing mounting plate. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.830.1326 Insert the third screw, found in hardware bag, into place and then tighten all three (3) screws.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Switch Housing Screw Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Align the keyhole slots in the lower switch housing with the switch housing screws. Place the lower switch housing, then twist the lower switch housing counterclockwise to lock into place.
www.HunterFan.com Light Kit (continued) Attach the LED assembly to the lower switch housing by installing two light kit assembly screws, found in the hardware bag. Insert the screws through the slots, not the screw holes, in the LED assembly. Connect the plug connectors between the black wire and the black wire with a white stripe. Connect the plug connectors between the two white wires. 9 M3523-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
www.HunterFan.com 1.888.830.
www.HunterFan.com Downrod (continued) 1.888.830.1326 Upper Motor Cover KEEP! ! KEEP Place the upper motor cover on the top of the fan. Align the notches in the upper motor cover with the tabs on the motor adapter. Insert the upper motor screws, found in the hardware bag, and tighten them securely. 11 M3523-01 • 05/14/14 • © Hunter Fan Company Remove the pre-installed setscrew so that the downrod can be inserted.
www.HunterFan.com (not to scale) & 3/8” 8” The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 1.888.830.1326 STRIP CUT Downrod (continued) 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 13 M3523-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. OM CEILING FR T KE AC FRO white FR M FA N OM FAN FR OM white ING BR white (grounded) Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 15 M3523-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Globe 1.888.830.1326 Tab Notch CONGRA YOU’RETULATIONS! DONE! Position the notches in the outer rim of the globe so they line up with the tabs on the inside surface of the light fixture rim. Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs. 16 M3523-01 • 05/14/14 • © Hunter Fan Company See next page for fan operation instructions.
www.HunterFan.com Remote Control 1.888.830.1326 If you are installing multiple remote-controlled fans on the same circuit breaker, you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls. Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for more information.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Medium Speed Fan Off High Speed Switch Cover Plate Low Speed Light Reverse Switch Removed Tabs To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on. Hold the Light button to raise and dim the light level. Rocker- Style Plate To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Use the provided balancing kit and instructions to balance the fan. • Make sure the blades spin freely.
