www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3541-01 • 05/14/14 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Ceiling Bracket www.HunterFan.com 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M3541-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. OM CEILING FR T KE AC FRO white FR M FA N OM FAN FR OM white ING BR white (grounded) Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Install the two canopy screws, found in the hardware bag. Note: Fan style may vary. 10 M3541-01 • 05/14/14 • © Hunter Fan Company 1.888.830.
Blades Insert each blade into a slot. Align the holes on the blade with the holes on the blade ring. www.HunterFan.com 1.888.830.1326 Attach the blade to the blade ring using the blade assembly screws, found in the hardware bag. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes.
Heat Shield www.HunterFan.com 1.888.830.1326 Machine Screw Partially install two machine screws, found in the hardware bag, halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wires through the center hole of the heat shield, then wrap the keyhole slots around the screws and twist counterclockwise. Use only the light fixture supplied with this fan model.
www.HunterFan.com Light Kit 1.888.830.1326 Machine Screw Partially install two machine screws, found in the hardware bag, into the screw holes in the heat shield. Connect the plug connectors between the black wire coming from the light kit and the blue wire coming from the motor housing. Connect the plug connectors between the white wire coming from the light kit and the white wire coming from the motor housing.
www.HunterFan.com Light Kit (continued) Install the third machine screw, found in the hardware bag, into the light kit. Make sure the light kit is securely attached to the heat shield. Failure to properly secure all three assembly screws could result in the light fixture falling. Tighten all three screws securely. 1.888.830.1326 Install a light bulb in each socket. Note: Do not use CFL bulbs to replace your light bulbs. Your lights may flicker or fail to work.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Screw Holes Decorative Screw CONGRA YOU’RETULATIONS! DONE! Glass Bowl Lift the glass bowl and align the screw holes in the glass bowl with the screw holes in the metal rods coming from the heat shield. Install the decorative screws into the metal rods to secure the glass bowl in place. 15 M3541-01 • 05/14/14 • © Hunter Fan Company See next page for remote operation instructions.
www.HunterFan.com Remote Control 1.888.830.1326 If you are installing multiple remote-controlled fans on the same circuit breaker, you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls. Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for more information.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Medium Speed Fan Off High Speed Reverse Switch Switch Cover Plate Low Speed Light Removed Tabs To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on. Hold the Light button to raise and dim the light level. Rocker- Style Plate To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
