Table of Contents www.HunterFan.com What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
What to Expect with Your Installation www.HunterFan.com Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
Tools Needed www.HunterFan.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3539-01 • 07/17/13 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.830.
Ceiling Bracket www.HunterFan.com 1.888.830.1326 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Preparation www.HunterFan.com A ISC R D D Ceiling Bracket (continued) DISC D AR Remove the shipping blocks from the motor. Discard the screws. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and discard the screws. Note: Fan style may vary. 6 M3539-01 • 07/17/13 • © Hunter Fan Company 1.888.830.
www.HunterFan.com 1.888.830.
www.HunterFan.com (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the upper globe. Set the upper globe in place on top of the fan. www.HunterFan.com Then put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3539-01 • 07/17/13 • © Hunter Fan Company 1.888.830.
Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
Canopy www.HunterFan.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3539-01 • 07/17/13 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to a blade iron. 1.888.830.1326 Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching.
Switch Housing Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the 1.888.830.1326 Insert the third screw, found in hardware bag, into place and then tighten all three (3) screws.
Light Kit www.HunterFan.com 1.888.830.1326 Upper Switch Housing A15 E12 Bulb Lower Switch Housing To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors are properly aligned before connecting them. Incorrect connection could cause improper operation and damage to the product.
Light Kit (continued) www.HunterFan.com Metal Disc Threaded Rod Glass Bowl Finial Cap Finial Cap Attach the extra pull chains (included) to the fan pull chain and light pull chain using the breakaway connector. (You may find the breakaway connector on the end of the extra chain.) Note: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output.
Light Kit (continued) www.HunterFan.com 1.888.830.1326 Upper Globe A15 E12 Bulb Light Pull Chain Fan Pull Chain CONGRA T YOU’REULATIONS! DONE! Install A15 E12 bulbs into the sockets. Note: Do not use CFL bulbs to replace your light bulbs. Your lights may flicker or fail to work. Connect the appropriate pull chain pendant to each of the short chains coming from the switch housing. 16 M3539-01 • 07/17/13 • © Hunter Fan Company See next page for fan operation instructions.
Maintenance & Cleaning www.HunterFan.com r we o nP 1.888.830.1326 Metal Plate r Tu ON Globe Reverse Switch Finial Cap Finial The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixtures. The chain has four settings in sequence: down light ON, up and down light ON, up light ON, and OFF. To switch the direction of air flow, move the reverse switch to the opposite position. Changing the bulbs - unscrew the finial and remove it from the threaded rod.
Troubleshooting www.HunterFan.com Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
