Prep Connect Complete Gatlinburg Installation Manual Model: 52429 Matte Black 52430 Matte Fresh White 52431 Matte Silver Fan weight ±2 lbs: 21.8 lbs (9.9 kg) ©2023 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
Tools Needed for Installation Box Outlet Mount Building Structure Mount 9/64" Box Contents Parts Included Hardware Included A Canopy Mount AA B Canopy I Remote C Fan Body Small Flat Head Screwdriver Wood Screw x2 D BB Snap-on Blades x5 Washer x2 E Light Kit F Glass Cover x4 H threadlocker Light Bulb x4 3
Before Beginning Installation Standard Mount OFF ON ON ON OFF OFF ON OFF OFF Turn Power OFF, breaker and light switch. This installation is for flat ceilings using the short pre-installed downrod ceiling fans. WARNING To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. IMPORTANT The longest accessory downrod that can be used with HunterExpress® fans is 12-inches.
a Installation – Canopy Mount and Terminal Wiring 1a Building Structure Mount 1 A Prep BB • You must be able to secure the fan to building structure or fan-rated outlet box. • You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. AA 2 Using wood screws (AA) and washers (BB) included, install canopy mount (A) through box outlet into building structure.
Installation – Canopy Mount and Terminal Wiring (continued) 1b Single Switch Wiring Connect wiring from ceiling to terminal block (on side of canopy mount) and tighten using flathead screwdriver (included). Green, Green Yellow Stripe, or Bare (grounding) White (grounded) WARNING The ceiling fan must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
Installation – Fan Body, Wiring Harness, Canopy Cover, and Blades Connect 2b 2a A A 2 B 1 B C B NOTICE C To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. Install snap-on canopy (B) over downrod on fan body (C). Place the down rod ball into the slot in canopy mount (A) with built-in ceiling bracket. 2c Connect wiring harness from canopy mount (A) to wiring harness from fan body (C).
Installation – Light Kit Notch Complete Remove the cardboard plug guard before proceeding! Pin 3c Raise the light kit to the bottom of the fan. Align the notch on the mounting ring on the top of the light kit with the pin in the mounting bracket on the bottom of the fan. 3a Connect the plugs from the fan and light fixture. Make sure to line up the colored markings on the connectors. IMPORTANT HOLD HERE 3b Push the connector and excess wire into the hole at the top of the light fixture.
Installation – Glass Cover Screw Bulb Glass 3e x4 Remove the screws from the sockets. Install the glass onto the sockets. Tighten them by turning clockwise by hand. 3f x4 Install a bulb into each of the sockets. When necessary, replace with bulbs of same wattage. WARNING GLASS FALL HAZARD To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured. ON OFF ON ON OFF OFF ON OFF ON Turn Power ON, breaker and main switch.
Operation – Remote Remote Function Guide Key Press Battery Door NOTICE Function + Quick Press Light On/Off + Long Press Light Dimming + Quick Press Fan On/Off + Quick Press + Quick Press Raise Fan Speed Lower Fan Speed + Long Press Fan Reverse Long Press Fan High Long Press Fan Low Long Press + Enable Beep Long Press + Disable Beep Long Press + Dimming Mode On/Off • Always purchase the correct size and grade of battery most suitable for the intended use.
Head Troubleshooting Goes Here Fan Does Not Work • Make sure power switch is on. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram. Excessive Wobbling • Make sure the blades are properly installed on the blade iron posts. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
Installation - Long Downrod 1 2 2 3 4 5 9 4 2 6 8 10 5 10 1 7 3 1. Loosen set screw (1) and remove ball screw (2). 2. Slide ball down (3), remove small metal pin (4) and ground screw (5). 3. Slide down inner sleeve (6). Place screwdriver through hole in downrod (7) making sure not to hit or twist wiring. Twist screwdriver counter-clockwise to break downrod free. 6 10 7 4. Remove ball, inner sleeve and downrod from fan body (8) and wiring harness. 5.
