www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed 1.866.268.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring 1.866.268.1936 Assess location w.
www.HunterFan.com Tools Needed Ladder Power Drill (optional) Screwdrivers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.866.268.
www.HunterFan.com Ceiling Bracket 1.866.268.1936 Bumper er w o nP r Tu OFF Make sure all four bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box.
Ceiling Bracket (continued) Preparation www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.866.268.
www.HunterFan.com Hanging the Fan Ground Wire Screw Hole While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Locking Screw Once the motor is in the ceiling bracket, use the two locking screws found in the hardware bag to secure the motor to the ceiling bracket. Note: Fan style may vary.
www.HunterFan.com Secondary Hanging System 3mm (1/8") 1.866.268.1936 Braided Cable Support Brace Outlet Box Insert the looped end of the braided cable through the ceiling bracket and one of the holes in the outlet box into the ceiling. Access the support brace in the ceiling. You may not be able to do this from below the ceiling depending on your installation site. Ceiling Drive the wood screw and washer found in the bag into the side of the support brace that holds the outlet box.
Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.HunterFan.com Motor Housing Notch Motor Housing Screw Indentation Screw Holes Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket. The motor housing is not secured until the next step is complete. Do not leave unattended. With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag.
Blades www.HunterFan.com Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 10 M0044-01 • 06/25/15 • © 2012–2015 Hunter Fan Company 1.866.268.
www.HunterFan.com Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.866.268.1936 Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Make sure the upper switch housing is securely attached to the mounting plate.
www.HunterFan.com Light Kit 1.866.268.1936 Notch Switch Housing Screw Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Want to install your fan without a light kit? Go to www.HunterFan.
www.HunterFan.com Light Kit (continued) Metal Plate Light Pull Chain 1.866.268.1936 Fan Pull Chain Globe Globe Keeper Finial Cap CONGRA YOU’RETULATIONS! DONE! Finial Install a bulb into each of the sockets. When necessary, replace with bulbs of the same type and wattage. Note: Glass shade style and number of lights may vary. Press the globe and globe keeper flush against the metal plate.
Maintenance, Operation & Cleaning r we o nP www.HunterFan.com 1.866.268.1936 Metal Plate r Tu ON Globe Globe Keeper Finial Cap Reverse Switch Finial Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check to see if any of the blades are cracked. If so, replace all of the blades.
