Prep Connect Complete Acela Installation Manual Model: 51674 Matte Silver 51675 Flat Matte Black Fan weight ±2 lbs: 19.6 lbs (8.9 kg) ©2021 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
Tools Needed for Installation Box Outlet Mount Building Structure Mount 9/64" Box Contents Hardware Included G Parts Included Cradle A Canopy Mount AA B Canopy H F C Fan Body Small Flat Head Screwdriver Cradle Bracket Remote I Tape Remote Screw x2 J Remote Door Screw BB Remote Drywall Anchor x2 D Snap-on Blades x5 CC Wood Screw x2 E Glass Cover DD Washer x2 threadlocker 3
Before Beginning Installation Standard Mount OFF ON ON ON OFF OFF ON OFF OFF Turn Power OFF, breaker and light switch. This installation is for flat ceilings using the short pre-installed downrod ceiling fans. WARNING To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. IMPORTANT The longest accessory downrod that can be used with HunterExpress® fans is 12-inches.
a Installation – Canopy Mount and Terminal Wiring 1a Building Structure Mount 1 A • You must be able to secure the fan to building structure or fan-rated outlet box. • You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. DD CC 2 Using wood screws (CC) and washers (DD) included, install canopy mount (A) through box outlet into building structure.
Installation – Canopy Mount and Terminal Wiring (continued) 1b Single Switch Wiring Connect wiring from ceiling to terminal block (on side of canopy mount) and tighten using flathead screwdriver (included). Green, Green Yellow Stripe, or Bare (grounding) White (grounded) WARNING The ceiling fan must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
Installation – Fan Body, Wiring Harness, Canopy Cover, and Blades 2a 2b A A 2 B 1 B C B NOTICE C To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. Install snap-on canopy (B) over downrod on fan body (C). Place the down rod ball into the slot in canopy mount (A) with built-in ceiling bracket. 2c Connect wiring harness from canopy mount (A) to wiring harness from fan body (C). 2d B D x5 2 1 C 2 Note: Follow the instructions on the blade.
Installation – Glass Cover 3 C 1 2 E Align, lift and twist to lock glass cover to bottom of fan assembly. WARNING GLASS FALL HAZARD To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured.
Installation – Remote Cradle 1a 1a Adhesive Option 1 H Screw Mount Option 1 H G BB G 2 3 H 2 I AA H H 3 Remove cradle (G) from cradle bracket (H). Separate lining from back of adhesive (I). Press cradle bracket (H) against wall for 30 seconds. Remove cradle (G) from cradle bracket (H). Drill two 9/64" holes, install cradle bracket (H) to wall with drywall anchors (BB) and screws (AA). 2 F G 2 1 H Slide the cradle (G) onto mounted cradle bracket (H). Place remote (F) into cradle.
Installation - Final ON OFF ON ON OFF OFF ON OFF ON Turn Power ON, breaker and main switch. Operation – Remote Key Press Battery Door Phillips Screw (J) To access the battery compartment, remove the small Phillips head screw (J) that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary.
Troubleshooting Fan Does Not Work • Make sure power switch is on. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram. Excessive Wobbling • Make sure the blades are properly installed on the blade iron posts. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
Installation - Long Downrod 1 2 2 3 4 5 9 4 2 6 8 10 5 10 1 7 3 1. Loosen set screw (1) and remove ball screw (2). 2. Slide ball down (3), remove small metal pin (4) and ground screw (5). 3. Slide down inner sleeve (6). Place screwdriver through hole in downrod (7) making sure not to hit or twist wiring. Twist screwdriver counter-clockwise to break downrod free. 4. Remove ball, inner sleeve and downrod from fan body (8) and wiring 6 10 8 9 2 7 10 4 10 7 harness. 5.
