42015-01 • 02/15/05
Welcome For Your Records and Warranty Assistance Model Name: _____________________ Catalog/Model No.: ________________ Serial No.: _______________________ Date Purchased: ___________________ Where Purchased: _________________ For reference also attach your receipt or a copy of your receipt to the manual. Table of Contents 1 • Getting Ready ...................................................4 2 2 • Installing the Hanger Bracket...................5 3 • Assembling and Hanging the Fan..........
Mounting and Optional Accessories Understanding Mounting Hunter’s patented mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angle mounting. e steps in this manual include instructions for both mounting methods. Considering Optional Accessories Consider using Hunter’s optional accessories, including a wall-mounted or remote speed control.
1 • Getting Ready To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician.
2 • Installing the Hanger Bracket 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. e pilot holes should be 9/64” in diameter. Note: Your fan comes with four pre-installed neoprene noise isolators. Isolator Hanger Bracket 2-2. read the lead wires from the outlet box down through the hole in the middle of the hanger bracket. 2-3. Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support structure.
3 • Assembling and Hanging the Fan Standard Mounting Washer Label Step 3-1 Canopy You can assemble your fan for standard or angle mounting as shown in steps 3-1 – 3-6. 3-1. Remove the label from the standard mounting washer inside the canopy. Leave the washer in place. 3-2. To assemble fan to hang down from a flat or angled ceiling, place the canopy with washer, and canopy trim ring around the adapter so that they rest on the fan assembly. 3-3. Feed the wires from the fan through the downrod. 3-4.
4 • Setting the Remote Transmitter and Receiver You must now set the jumper switches in the remote transmitter and receiver so that they match. 4-1. Change the position of the jumper switches in the transmitter and the receiver. Be sure the position of the jumper switches matches. If they don’t match, the controller will not function. For instructions on how to set the jumper switches, read the box below. 4-2. Install the included 12-volt battery into the transmitter.
5 • Wiring the Fan Antenna All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. 5-1. Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. 5-2. To connect the wires, hold the bare metal leads together and place a wire nut over them, then twist clockwise until tight. For all these connections use the larger wire nuts provided.
6 • Installing the Canopy and Canopy Trim Ring 6-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. Steps 6-1 – 6-2 Hanger Bracket 6-2. Raise the canopy over the hanger bracket (For low profile installations, you will need to remove the canopy from the hook first). Align partially installed screws with key slots in canopy. 6-3. Twist canopy clockwise to secure. 6-4. Install third canopy screw in round hole on canopy. Securely tighten all three screws.
7 • Assembling the Blades 7-1. Insert blade into slot. Align the holes on the blade with the holes on the blade iron. 7-2. Attach the blade to the motor using the blade assembly screws. Note: Do not use the middle hole on the blade. 7-3. Repeat for each blade.
8 • Installing the Glass 8-1. Raise the glass to the fan assembly. 8-2. While holding up the glass, align the thumbscrew, the hole in the glass, and the post on the motor housing. 8-3. Install three (3) thumbscrews. 8-4. Install 1 standard A-19 bulb (100W max).
9 • Operating the Remote Control and Mounting the Holder 9-1. e remote transmitter has individual buttons for turning the fan off and on and controlling the light and fan speed. Fan Speed High Fan Speed Medium Fan Speed Low Fan Off Fan Light 9-2. For best operation, start the fan by pressing high, then select your desired speed. 9-3. e light button turns the light on to full brightness. To dim the light, hold the light button down until you reach your desired brightness.
10 • Operating and Cleaning Your Ceiling Fan 10-1. Restore power at the main electrical panel and turn on the wall switch. e light kit should turn ON. Note: To turn on the light without the remote, turn off the wall switch for 5 seconds, then back on. e light kit will turn on at maximum brightness. 10-2. Press the remote control’s HIGH speed button. e fan should start and reach its maximum speed. Note: For everyday operation, leave the wall switch ON.
11 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly up or down to ensure that the switch is engaged. Problem: Noisy operation. 1. Tighten the blade screws until snug. 2. Check to see if the blade is cracked. If so, replace all the blades. 3. Be sure that the glass is secure.
