For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name Type 5 Models Owner’s Guide and Installation Manual __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased English Español Form# 42858-01 20090910 ©2009 Hunter Fan Co.
Welcome Your new Hunter® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We are proud of our work. We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
Installer’s Choice and Optional Accessories Understanding Mounting and Installer’s Choice® Support Brace Standard Mounting Style Ceiling Outlet Box Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard, or Angle mounting. The steps in this manual include instructions for only one Installer’s Choice mounting method.
1 • Getting Ready To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician.
2 • Installing the Ceiling Plate CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” in diameter.
3 • Assembling Pipe / Ball Assembly Your Hunter fan comes with an optional downrod extension pipe. If you would like to use the enclosed optional downrod, complete the steps below. If you are going to install the fan using the standard downrod, go to “Step 4 - Assembling the Fan.” Removing Ball Assembly For the following steps refer to Figures 3b and 3c. 3-1. Locate the 4 1/2" pipe/ball assembly. 3-2. Remove the positioning screw from the top of the ball.
4 • Assembling and Hanging the Fan WARNING: Fan may fall if not assembled as directed in these installation instructions. Steps 4-2 – 4-3 4-1. Unbundle the wires from the fan. For Standard or Angle mounting: Downrod 4-2. To assemble fan to hang down from a flat or angled ceiling, insert the downrod through the canopy. Feed the wires from the fan through the downrod. Canopy 4-3. Loosen the square head set screw on the adapter to install the pipe and ball assembly.
fsdfsdf 5 • Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70-1999. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electrical codes. 5-1. Before attempting installation, make sure the power is still off. 5-2.
6 • Installing the Canopy 6-1. Partially install two canopy screws into the ceiling plate and rotate one time. Step 6-2 Ceiling Plate 6-2. Holding the canopy, raise the fan off the hook. 6-3. Align the slots in the canopy with the already partially installed canopy screws on the ceiling plate. 6-4. Raise the canopy over the ceiling plate. Rotate the canopy clockwise until the canopy screws on the ceiling plate totally engage with the slots in the canopy. Canopy 6-5.
7 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 7-1. Install the grommets into the blades by hand. Step 7-1 (Detail) 7-2. Place each blade between a blade iron and medallion. Install three blade screws to attach the medallion to the blade iron. Repeat for all blades. 7-3. For each blade, insert one blade mounting screw through the blade iron, and attach lightly to the fan.
8 • Completing Your Installation With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. The switch housing assembly is made up of three sections: the switch housing gasket, the upper switch housing, and the lower switch housing/light assembly. ATTACHING THE SWITCH HOUSING GASKET 8-1. Locate the switch housing mounting plate, the switch housing gasket and the upper plug connector.
8 • Completing Your Installation With a Bowl Light Fixture (continued) ATTACHING THE UPPER SWITCH HOUSING 8-5. Locate the four #6-32 X 1/4" switch housing mounting screws in the sack parts. 8-6. Feed the upper plug connector through the center hole in the upper switch housing. 8-7. Align the holes in the upper switch housing with the spokes in the mounting plate. 8-8. Insert and tighten the four #6-32 X 1/4" screws into the outermost holes in the upper switch housing.
8 • Completing Your Installation With a Bowl Light Fixture (continued) 8-12. Align the keyhole slots in the upper switch housing with the housing assembly screws installed in Step 8-8. 8-13. Turn the lower switch housing clockwise until the housing assembly screws installed in sub-steps 1 and 2 are firmly situated in the narrow end of the keyhole slots. Tighten all four screws firmly. 8-14. Partially install two of the screws into the lower switch housing to mount the globe assembly. 8-15.
9 • Replacing The Light Bulb Instructions for unassembling the globe when replacing a light bulb. 9-1. Unassemble the finial assembly as shown. 9-2. Install candelabra light bulb. 9-3. Loosely reassemble the finial bracket, cover plate, and finial. 9-4. Assemble the finial to the bottom of the globe assembly. Viewing the assembly through the globe, line up the finial bracket with the tabs in the bottom part of the globe assembly. 9-5. Securely tighten the finial.
10 • Operating and Cleaning Your Ceiling Fan 10-1. Turn on electrical power to the fan. 10-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low, Serenity Speed, and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. • The chain uses a breakaway connector that separates if the chain is jerked. If this happens, simply reinsert the chain into the connector.
11 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly left or right to ensure that the switch is engaged. 5. Pull the pull chain to ensure it is on. 6. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade bracket screws until snug. 2.
