Installation Sheet

INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION
For Models:
Para los Modelos:
Pour les Modèles:
Here are the
tools you’ll
need to
complete your
installation:
Estas son las
herramientas
que usted
necesitará para
completar su
instalación:
Voici les outils
dont vous
aurez besoin
pour réaliser
l’installation:
Ladder
Escalera
Échelle
Screwdriver
Destornilladore
Tournevis
Pliers
Alicates
Pince
Wire Strippers
Pelacables
Pince à dénuder
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It
is very important that they are read carefully and
completely before beginning installation of the
lighting xture.
LEA Y GUARDE ESTAS INSTRUCCIONES
Estas instrucciones se proporcionan para su
seguridad. Es muy importante leerlas detenid-
amente y completamente antes de comenzar la
instalación de la lámpara.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
Ces instructions sont fournies pour votre sécurité.
Il est très important de les lire attentivement dans
leur intégralité avant d’entreprendre l’installation
du luminaire.
Fixture weight ±2 lbs:
Peso ±2 lb:
Poids xe ±2 lbs:
•
WARNING
• All wiring must be in accordance with national
and local electrical codes ANSI/NFPA 70. If you
are unfamiliar with wiring or in doubt, consult a
qualied electrician.
• To avoid possible electrical shock, before
installing your light xture, disconnect the power
by turning off the circuit breakers to the outlet box
associated with the wall switch location.
• The lighting xture must be grounded. If the
ground wire for the installation site is not present,
immediately STOP installation and consult a
qualied electrician.
•
• Todo el cableado debe realizarse de acuerdo con
los códigos eléctricos locales y nacionales ANSI/
NFPA 70. Si no está familiarizado con el cableado,
o si tiene duda, consulte a un electricista calicado.
• Para evitar una posible descarga eléctrica, antes
de instalar su lámpara, desconecte la energía
apagando los interruptores automáticos (breakers)
que alimentan la caja de salida asociada con la
ubicación del interruptor de pared.
ADVERTENCIA
• L’appareil d’éclairage doit être mis à la terre.
Si le l de terre du lieu d’installation n’est pas
présent, ARRÊTEZ immédiatement l’installation et
consultez un électricien qualié.
•
AVERTISSEMENT
• Tout le câblage doit être conforme aux codes
électriques nationaux et locaux en vigueur et à la
norme ANSI/NFPA70. Si vous n'avez pas l'habitude
de faire ce câblage ou en cas de doute, adressez-
vous à un électricien qualié.
• Pour éviter tout choc électrique, avant d’installer
le luminaire, coupez le courant en éteignant les
disjoncteurs de la boîte électrique associée à
l’interrupteur mural.
• Le luminaire doit être mis à la terre. Si le l
de terre du lieu d’installation n’est pas présent,
ARRÊTER immédiatement l’installation et
consulter un électricien qualié.
©2021 Hunter Fan Co.
Linear Chandelier
Lámpara Lineal
Chandelier Linéaire
Part #/Pieza #/Pièce #
Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De
Maintenance Quincaillerie
ENGLISH
Twist or tape wire
ends together to make
it easier to thread
through downrod
Hunter Pro Tip:
NOTICE
In order to use a 12in rod by
itself you must rst remove
the post from the 6in rod and
install it on one of the ends of
the 12in rod.
NOTICE
Drill 9/64" pilot holes in
support structure to aid in
securing light xture.
Drill
Taladro
Foret
Finish/Finish/FiniModel/Modelo/Modèle
O
Q
P
R
H
I
K
L
M
N
E
D
C
B
A
G
F
J
S
T
U
19042
19667
Starklake
KC03101834
KC03101872
Noble Bronze/Bronce Noble/
Bronze Noble
Natural Iron/Hierro Natural/
Fer Naturel
19042
19667
ML015
r_092421
14.02 lbs (6.36 kg)
5
5
5
FINISHING THE INSTALLATION
CONNECTING THE WIRES
ASSEMBLING THE FIXTURE
PREPARING FOR INSTALLATION
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light
and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old
xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the
bag. Put the drywall anchor (H) inside the hole in the ceiling. Place the mounting plate (B) over the junction box so that
mounting screws (A) extend out away from the ceiling. Pull the house wires through the center of mounting plate (B).
Secure mounting plate (B) to the junction box by tightening the screws (D) then insert the drywall screw (I) through the
mounting plate (B) into the drywall anchor (H).
There are 4 12-inch rods (P), and 1 6-inch rod (Q) included for each side of the xture. Determine the correct number
of rods needed for proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the
wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods
off the xture’s wiring to discard. Keep in mind that you must use at least one rod to hang the xture on each side.
Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw the lower
end of rod onto threaded post (R) of the xture. Place reinforcing plate (M) inside canopy (G) and the canopy (G) over
the threaded post (O) of the top rod. Put the center of threaded post (O) through the wirerope loop (F) and washer (L).
Lock the reinforcing plate and canopy with the wing nut (K) on threaded post (O). Hide wirerope inside the canopy (G).
Secure the screw collar loop (J) into mounting plate (B).
Have a helper support the xture’s weight while completing the
wiring. Attach the xtures wires to the power supply wires from the
junction box. Connect black to black (Live); white to white (grounded);
grounding to grounding (green or copper). Twist the ends of the
wire pairs together. Then, twist on a wire connector. Make sure all
twists are in the same direction. Loop xture’s ground wire around
grounding screw (E) and tighten. If there is no ground wire (green or
copper) from the junction box, contact a qualied electrician.
Raise canopy (G) to mounting plate (B) and position mounting screws (A) so that they protrude through the openings of
canopy (G). Secure canopy (G) in place with cap nuts (N). Install light bulb (not included) in accordance with the xture’s
specications. Do not exceed the recommended wattage. Secure cage (U) onto the socket (S) with screws (T). Your
installation is now complete. Turn on the power and test the xture.