www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location w.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3596-01 • 01/08/15 • © Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. If your ceiling angle is less than 34°, hang your fan by the standard downrod (included). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
Ceiling Bracket www.HunterFan.com 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com 1.888.830.
www.HunterFan.com CUT Tip: If you have difficulty feeding the wires through the downrod, try taping the wires to a thin dowel rod, then drop the dowel rod and wires through the downrod. Be sure to remove all tape once the wires are fed through to the other side. KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M3596-01 • 01/08/15 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Secondary Hanging System 1.888.830.1326 Wire Clamp Insert the end of the braided cable through the ceiling bracket and one of the holes in the outlet box into the ceiling. Access the support brace in the ceiling. You may not be able to do this from below the ceiling depending on your installation site. Loosen the two nuts on the wire clamp and slide the clamp open. Thread the end of the cable up through the wire clamp.
Wiring OM FR CEILIN Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G Green/Yellow Stripe 1.888.830.1326 G Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 11 M3596-01 • 01/08/15 • © Hunter Fan Company 1.888.830.
Blades www.HunterFan.com 1.888.830.1326 Screw Holes Lift a blade ring to the motor assembly and align the screw holes. Install three blade assembly screws, found in the hardware bag. If you wish to install your fan with three blades, skip to the next page. Note: In order to provide proper blade support, choose the three small screw holes that are aligned with the three arms of the blade ring as shown in the illustration.
Blades (continued) www.HunterFan.com Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Attach each blade to the blade ring using three blade assembly screws, found in the hardware bag. 13 M3596-01 • 01/08/15 • © Hunter Fan Company 1.888.830.
Finial www.HunterFan.com Screw the finial onto the threaded rod found at the bottom of the motor assembly. 14 M3596-01 • 01/08/15 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Wall Control 1. 1. 2. Shut off power to the room you will be working in at the breaker box. After removing the switch plate cover, remove all wiring from the switch. 1.888.830.1326 1. 2. Using the wire connectors, connect each black wire from the wall control to a black wire from the switch box. Note: If two white wires are present in the switch box, connect them to each other if they are not already connected. Do not restore power until all work is complete.
www.HunterFan.com Wall Control (continued) 1. CONGRA T YOU’REUALTIONS! DONE! 2. Remove the knob from the wall control and mount the faceplate (not included) to the wall control using the two #6-32 screws you removed earlier from the faceplate. Reattach the knob onto the wall control and turn it to the left for the OFF position. 16 M3596-01 • 01/08/15 • © Hunter Fan Company 1.888.830.
www.HunterFan.com Operation, Maintenance & Cleaning 1.888.830.1326 Reverse Switch r we o nP r Tu ON The knob on the wall control unit controls power to the fan. The fan has four speed settings in sequence: high, medium, low and off. To change the direction of air flow, move the reverse switch to the opposite position. 17 M3596-01 • 01/08/15 • © Hunter Fan Company For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade ring screws until they are snug. • Tighten the blade and blade ring screws until they are snug. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Check to see if any of the blades are cracked. If so, replace all of the blades.
