User's Manual
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the F
reasonable protection against harmful interference in a reside
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, ther
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, w
equipment off and on, the user is encouraged to try to correct the interference b
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority t
Industry Canada
Under Industry Canad
a regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for t
Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be s
power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada licence‐
exempt RSS standard(s). Operation is subject to the following two condition
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
Industrie Canada
Conformément à la réglementation d’Industrie Canada, le présent émett
approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention
d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessair
satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applica
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouilla
susceptible d’en compromettre le fonctionnement.
European Conformity
We, the undersigned,
Hunter Douglas Window Fashions
Address: One Duette Way, Broomfield, CO 80020, USA
Authorized representative in Europe: Nico Dekker
Hunter Douglas Europe B.V.
Piekstraat 2, 3071 EL Rotterdam, The Netherlands
certify and declare under our sole responsibility that the PV4
1999/5/EC.
A copy of the original d
eclaration of conformity may be found at
Location of FCC label on
Location of FCC label on assembly
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the F
CC Rules. These limits are designed to provide
reasonable protection against harmful interference in a reside
ntial installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, ther
e is no guarantee that interf
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, w
hich can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference b
y one or more of the following measures:
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority t
o operate the equipment.
a regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for t
Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be s
o chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
exempt RSS standard(s). Operation is subject to the following two condition
s: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
the device.
Conformément à la réglementation d’Industrie Canada, le présent émett
eur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention
des autres utilisateurs, il faut choisir
d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessair
e à l’établissement d’une communication
Le présent appareil est conforme aux CNR d’Industrie Canada applica
bles aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouilla
ge radioélectrique subi, même si le b
assembly conforms with the essential requirements of the
EMC directive 2004/108/EC and
eclaration of conformity may be found at
www.hunterdouglas.com/RFcertifications.
Location of FCC label on
assembly
Location of FCC label on assembly
CC Rules. These limits are designed to provide
ntial installation. This equipment generates, uses and can radiate radio frequency energy and, if not
e is no guarantee that interf
erence will
hich can be determined by turning the
o operate the equipment.
a regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for t
he transmitter by
o chosen that the equivalent isotropically radiated
s: (1) this device may not cause
the device.
eur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur)
des autres utilisateurs, il faut choisir
le type
e à l’établissement d’une communication
bles aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
ge radioélectrique subi, même si le b
rouillage est
EMC directive 2004/108/EC and
R&TTE directive