User's Manual

Test the Assembly Using the Remote
Refer to the PowerView™ Remote Guide for more information
To link a shade to a remote:
1. Press and hold
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
program mode.
2.
Press and hold the manual control button on the
3.
While continuing to press the manual button, press
been linked to the network.
4. Press and hold Stop
for six seconds to exit program mode.
To join a shade to a GROUP:
1. Press and hold
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
program mode.
2. Press desired group number (1 –
6) on the remote.
selected.
3.
Press and hold the manual control button on the
4.
While continuing to press the manual button, Press
has joined the group.
5. Press and hold
Stop for six seconds to exit program mode.
To remove a shade from a group:
1. Press and hold
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
program mode.
2. Press desired group number (1 –
6) on the remote. The light for the group number selected will pulsate to show it is
selected.
3.
Press and hold the manual control button on the
4.
While continuing to press the manual button, Press
removed from the group.
Radio Control Operation
Once the assembly has
been joined to a group, radio control is used to operate the
toward the assembly being operated. Multiple
assemblies
Remote Functions:
1. To wake up remote, press
Stop. The last group(s) selected will be highlighted and active.
2. Press “All” or Groups 1‐
6 to select specific shade(s) to move. Selected
a. Multiple Group number may be selected at a time.
b.
To deselect a Group, press the Group number again. The light for that group will go out.
3. Select the OPEN button to
move the motor in one direction
4. Select the CLOSE button to
move the motor in the other direction
5. While a motor is in motion, press
OPEN or
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
Press and hold the manual control button on the
assembly.
While continuing to press the manual button, press
Stop on the remote. The motor will
rotate slightly
for six seconds to exit program mode.
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
6) on the remote.
The light for the group number selected will pulsate to show it is
Press and hold the manual control button on the
assembly.
While continuing to press the manual button, Press
Open on the remote. The motor will
rotate slightly
Stop for six seconds to exit program mode.
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
6) on the remote. The light for the group number selected will pulsate to show it is
Press and hold the manual control button on the
assembly.
While continuing to press the manual button, Press
Close on the remot
e. The shade will jog to indicate it has been
been joined to a group, radio control is used to operate the
motor
. There is no need to aim the remote
assemblies
can be operated at the same time.
Stop. The last group(s) selected will be highlighted and active.
6 to select specific shade(s) to move. Selected
groups will light to show they are selected.
a. Multiple Group number may be selected at a time.
To deselect a Group, press the Group number again. The light for that group will go out.
move the motor in one direction
.
move the motor in the other direction
.
OPEN or
CLOSE, the opposite of motor
motion to reverse direction.
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
rotate slightly
to indicate it has
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
The light for the group number selected will pulsate to show it is
rotate slightly
to indicate it
Stop for six seconds to put remote in program mode. The lights on remote will pulsate to indicate it is in
6) on the remote. The light for the group number selected will pulsate to show it is
e. The shade will jog to indicate it has been
. There is no need to aim the remote
groups will light to show they are selected.
motion to reverse direction.