Confidential 1DX Installation Manual FCC ID of this product is as follows. FCC ID: UXU1DX IC No. of this product is as follows. IC : 7316A-1DX For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC and IC on the product and in the Installation manual Notice. Contents 1.Voltage 2.Antenna 3.Notice Copyright © Hunter Douglas Window Fashions All rights reserved.
Confidential 1.Supply Voltage min. typ. max. unit Specification Temperature Range -40 +25 +85 deg.C Specification Voltage VBAT 3.0 3.6 4.8 V VDDIO 1.71 1.8or3.3 3.63 V Copyright © Hunter Douglas Window Fashions All rights reserved.
Confidential 2.Antenna ■Please perform the antenna design that followed the specifications of the antenna. The concrete contents of a check are the following three points. １）It is the same type as the antenna type of antenna specifications. The trace reference design section is provided under a separate non-disclosure agreement ２）An antenna gain is lower than a gain given in antenna specifications. Measure the gain, and confirm the peak gain is less than the application value (1.
Confidential 3.Notice For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC/IC on the product and in the Installation manual Notice. Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID: UXU1DX or Contains FCC ID: UXU1DX and Contains IC: 7316A-1DX Copyright © Hunter Douglas Window Fashions All rights reserved.
Confidential 3.Notice ●Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Confidential 3.Notice ●When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
Confidential 3.Notice ●When installing it in a portable equipment. It is necessary to take a SAR test with your set mounting this module. Class II permissive change application is necessary using the SAR report. Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. Copyright © Hunter Douglas Window Fashions All rights reserved.
Confidential 3.Notice This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 1.4 dBi. As long as 3 conditions above are met, further transmitter test will not be required.
Confidential 3.Notice IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Confidential IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
