3000 wireless video transmission system supporting HDMI & SDI (VAXIS STORM3000) FCC ID:2AJOF-3000
User manual 1. Cautions ..................................................................................................1 2. About.......................................................................................................2 3. Installation.............................................................................................10 4. Operation instruction ............................................................................11 5. Maintenance.............................................
1. Cautions ■Logo and meaning Careful, warning, dangerous, Pay attend to following items. ■Cautions Do not use this product in the extreme hot, cold, dusty or humid environments. Prevent friction with hard objects. Avoid the product falling down from a high place, or it may damage the hardware. The product is not water proofed. So do not get any liquid into the unit please. Do not dismantle, assemble or alter the product arbitrarily.
2. About ■Product model and standard The VAXIS STORM3000 Wireless HDMI/SDI Transmission Suite utilize today’s most advanced wireless video transmission technology, which can realize the broadcast-class and uncompressed 3G SDI/HDMI HD video signal transmitted with no compression and zero delay. The suite includes one transmitter and one receiver, where the transmitter provides a 3G/HD SDI input and a HDMI input, and the receiver also provides a 3G/HD SDI output and a HDMI output.
■Main features: HDMI 1.3 spec supports HDMI and 3G SDI input and output 24fps frame rates Highest resolution 1080p 60，no delay and no compression Support audio formats include Dolby True HD, DTS-master, etc. AES-128 encryption with air interface HD video data stream Support point to point, and point to multi points network topology 5GHz ISM frequency band，maximum 10 frequency channels selected by user knob, coexist with WIFI.
■ Parameters: Transmitter Receiver SDI Input（BNC Female）; SDI loop out SDI Output X 2（BNC Female）; HDMI （BNC Female）; HDMI Input(Type A Output(Type female); 2 Antenna port(2 SMA male）; port(SMA male）; DC input (2 pin LEMO DC input (2 pin LEMO female) female) Supply voltage range 6-36V DC 6-36V DC Power consumption <6.
Modulation Mode OFDM 16QAM OFDM 16QAM Transmission Power Maximum 18dBm for FCC / Receiver Sensitivity / -75dBm Occupied Bandwidth 40MHz 40MHz Temperature Range 0 Compliance ~ 40°C (operating condition); 0 ~ 40°C (operating -20~60°C(Storage) -20~60°C(Storage) FCC; CE. FCC; CE.
⑨ Antenna interface ⑩ DC input, LEMO 2-pin B series connector Receiver: ① DC power switch ② HDMI Output ③ 3G-SDI Output1 ④ 3G-SDI Output2 ⑤ Antenna interface ⑥ HDMI Output ⑦ Channel Button “+” ⑧ Channel Button “-” ⑨ USB debugging interface ⑩ DC input, LEMO 2-pin B series connector
Screen Operation: ①Temperature display ②Fan’s speed display ③Channel display ④Signal strength display ⑤Signal source display ⑥Signal input format display ⑦0`S function ⑧Battery voltage display ■Packing list: 1x unit Transmitter 1x unit Receiver 7x 5GHz sword Antennas 2x DC convert cable (LEMO 2 pin-male to D-Type receptacle) 1x 1/4-20 screw to ISO518 hot-shoe converter 1x 7” Articulating magic arm 1x User Manual VAXIS flight case
3. Installation ■Installation details and cautions Transmitter side a) Install 2 Omni-directional and high efficiency antennas to Transmitter’s SMA male antenna connectors. b) There are 3 1/4-20 screw nuts in transmitter metal case, which are located on the bottom. So the user can utilize a 1/4 screw to ISO518 hot-shoe converter fix the transmitter on camera. c) The user can also utilize a subsidiary LEMO 2 pin male to D-Type receptacle power cable to get power input from an outside power source.
4. Operation instruction ■Getting started After finishing all steps above, system is workable, follow below steps. a) Ensure the video source output of the camera is OK, and the HD monitor is power on and switched to connected video input port. b) Ensure all input, output SDI or HDMI cables are connected. c) Ensure all antennas are installed, and it is better to keep TX 2 antennas and RX 5 antennas with orthogonal angle each other for best RF performance.
h) The system will spend about 20 seconds on constructing communication link, and real link period will depend on the current wireless channel condition. When wireless link is set up, ④will display wireless signal strength, as well ⑤ will light, means had receive the normal signal; then connected HD monitor will display the HD video and audio from TX module. i) For the best wireless transmission performance, it need install the transmitter and receiver more than 1.
■ Input video port selection of transmitter The transmitter has a 3G SDI video input port and a HDMI video input port, and the system will detect valid video source automatically of SDI and HDMI port, and then switch it as main video input channel. If both SDI and HDMI have valid video inputs, the system will take SDI input as priority. ■ RSSI indicators The receiver will calculate received RF signal strength internally and The OLED Screen will indicate wireless signal power and quality.
5. Maintenance ■Storage conditions Products storage temperature should be -20°C~60°C. For long time storage requirement, please use original carbon boxes, and avoid from high humid, acid base or dusty place. ■Maintenance Warning To ensure your safety, place choose well-known brand DC batteries, and guarantee suitable work conditions that battery manual mentioned. 6.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
