October 2017 Humidex GVS-SD2 Owner’s Manual Manufactured by: Clairitech Innovations Inc. 1095 Ohio Rd. Boudreau-West, NB Canada E4P 6N4 Rev. 1.
Humidex Table of Contents Table of Contents 1 Service and Warranty 2 FOR CUSTOMER ASSISTANCE 2 CONSUMER LIMITED WARRANTY 3 Before Installing 5 TECHNICAL DATA 5 RECOMMENDED TOOLS REQUIRED FOR INSTALLATION 5 INCLUDED PARTS LIST 5 IDEAL INSTALLATION LOCATION 5 WARNINGS FOR USE 6 Installation 7 How to Operate the Humidex 8 Wiring Diagram 10 1
Humidex Service and Warranty For customer assistance To aid in answering questions if you call for service or warranty purposes, please record below the model and serial number located on the side of the unit. Product name: Model #: Date of manufacturing: Serial #: Dealer name (if any): For the following inquiries: - Service Parts Accessories Additional customer information Please contact us by: Phone: 1-888-533-1348 Email: support@humidex.ca Website: www.humidex.
Humidex Consumer Limited Warranty Clairitech Innovations Inc. warrants to the first consumer that this Humidex product, when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its discretion, either repair the defect or replace the defective product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
Humidex The warranties described herein shall be the sole and exclusive warranties granted by Clairitech and shall be the sole and exclusive remedy available to the purchaser.
Humidex Before Installing Technical data Voltage: Amperage Certification: Dimensions: Capacity: 115VAC 0.26A 9” x 6.5” x 4” Up to 750 sq. ft. Recommended tools required for installation - 1/4’’ pilot drill bit of 12 inches or more Hole saw with a diameter of 4 ½”, reciprocal saw or, jig saw Measuring tape Hammer Screwdriver Included parts list Garage Ventilation System 4” Exhaust Vent 1Pc. Aluminum Tape Warranty Card 1pc.
Humidex Warnings for use The following warnings will help reduce the risk of fire, electric shock or injury. Please read and save these instructions. 1) Do not operate any unit with a damaged cord or plug. Please contact our service department for examination and/or repair. 2) Do not run cord under any object, which include but limited to, carpets, furniture, appliances etc. Arrange cord away from traffic area. 3) The unit MUST exhaust the air outside.
Humidex Installation Please follow these instructions to install your Humidex properly. 1. From the inside, mark where the center of the Humidex will be placed and drill through the wall with a ¼’’x 12’’ pilot bit. The hole should be approximately 12 inches from the floor. Cut a 4 ½’’ hole through the wall. 2. From the inside, place the Humidex against the wall in the mounting position and mark where the pilot screws will be placed. Keep in mind that the knob will be going on the right hand side.
Humidex How to Operate the Humidex After both the Humidex and the exhaust vent are properly installed, you can now plug the Humidex in the closest outlet. The Humidex unit possesses a label illuminated by LEDs that will indicate the set humidity preference, if the unit is powered On and if the unit has detected a higher than usual amount of CO. To set your humidity preference, press the center button of the label to cycle through the different humidity settings.
Humidex How the CO Sensor Works The built-in carbon monoxide sensor allows the unit to monitor the garage or shed for any amount of CO in the air. To help the user understand the unit’s process an indicator light has been added The indicator light will have three (3) different display modes Double blink mode: In order to function properly, the CO sensor is required to warmup, during these warmup sequences the indicator light will blink twice.
Humidex Wiring Diagram 10
