Specifications

File no.: QR004 REV.A
Huizhou Yuansheng Technology Co.,Ltd
Address: Zhongkai High-tech Zones on 16th. HuiFengEast No. 2 road, Building B Room 516,518,
Huizhou city, Guangdong Province, China
Tel.: [phone] Fax: [phone] Website: www.cnmicrowavesensor.com
45/ 5 To be the most professional digital switches manufacturer that provides best service!
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this module installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization
is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AXVDMW-0172"
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a
stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
2.4 Limited module procedures
This module is Limited single modular without shielding, host manufacturer have to consult with module manufacturer for the module limiting conditions when
integrate the module in the host. module manufacturer should reviews detailed test data or host designs prior to giving the host manufacturer approval.
2.5 Trace antenna designs
Not applicable
2.6 RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
2.7 Antennas
The Microwave sensor module is not designed for multiple antenna applications and should not be used to transmit simultaneously with any other transmitter.
The Microwave sensor module is only certified to use the integrated PCB antenna.Antenna Description:PCB Antenna antenna,Max Gain:2.1dBi.
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following" Contains FCC ID:2AXVDMW-0172".
2.9 Information on test modes and additional testing requirements
Host manufacturer which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according t o FCC
part 15C:15.249 and 15.209 requirement, only if the test result comply with FCC part 15.249 and 15.209 requirement, then the host can be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15
B.