Robotic vacuum cleaner Manual User Manual Thanks for buying this product,before using it, please read the following instructions carefully and keep it well.
Table of Contents 1. Security Information.....................................................................1-2 2. Product Composition....................................................................... 3 2.1 Product Parts Display........................................................................................... 3 2.2 Product Parts Name............................................................................................. 3 3. Product Usage................................................
安置昂 is 荟萃收到货举报、池安装八、电池安装遥 1．Safety Regulations Before using this product,please read the following safety instructions and follow all routine safety precautions. Please read the instructions carefully,please keep the instructions . Any 0peration inconsistent with this instruction manual may cause damage to this product. Note 1. Only authorized technicians can disassemble this product.Users are not recommended to disassemble this product by themselves. 2.
Warning 1. Use only the original rechargeable battery and charging seat specially equipped by the manufacturer.Non-rechargeable batteries are structure prohibited,please refer to “product parameters”for battery specification information. 2. It is forbidden to use products in environments with open flames or fragile objects. 3. It is forbidden to use product in extremely hot (above 40℃）or extremely cold(below 0℃ ）. 4.
2.
3. Product Usage Instructions of Press Button Functions Power key （1） The power key is at the bottom of this robot， “ ” Power on key，“ using this product, make sure that the power switch is on. ” Power off key。Before Automatic cleaning key （2） At first, make sure that the power switch at the bottom of this product is on, and then click “ ” key，the zigzag cleaning mode starts automatically；During the cleaning process，click “ ” key，the product pauses.
Charging Instructions (1) Automatic Charging： Please place the charging base against the wall, remove all obstacles 1 meter on the left and right and 2 meters in front of it, and then connect the power supply. When the power is insufficient, robot cleaner will automatically source the recharge seat to charge; In the selection mode (power on status), press the recharge button on the host panel, and it will automatically source the recharge base for charging，as shown in Figure 1 and 2.
(3) Please turn off the power switch of robot vacuum cleaner before installing or removing the rechargeable battery. Figure 3 Figure 4 screw/ nu t Ba tte ry house Installation and Removal Steps of Side Brushes （1）Installation Step: press side brush directly into the center convex shaft of the brush holder to complete the installation.(As shown in Figure 5) （2）Disassembly Step: hold side brush and pull the central convex shaft from the Brush holder.
Instructions of Mop Usage Attention：Please do not have the mopping function happen on the carpet or environments with carpet. (1) Please take the mop carriage and fix it on right position , as shown in Figure 7 (2) Soak the mop cloth in water. (3) Stick the mop to the corresponding position as shown in the figure. (4) Disassemble mop: Just rip it off the MOP board Warm tips: please clean the mop cloth in time after mopping the floor each time.
(2) Turn on the switch key at the bottom of robot cleaner and press the recharge key for 3 seconds. At this moment the red indicator goes out and the green indicator flashes quickly, indicating that the WiFi has been turned on ,the mode of fast distribution network is ready, and waiting for the connection to be established.
Robot Vacuum *********** (3) After the distribution network of WiFi is completed, you can start to operate robot cleaner; as shown in the figure below.
4. Cleaning and Maintenance of Product Cleaning of Dust Box and HEPA Warm tips: in order to achieve the best cleaning effect, please check and clean the foreign matters on HEPA before use product, and keep the HEPA unblocked. (1) Open the upper cover, put your fingers into the groove of the dust box, hold the dust box tightly and take it out upward. As shown in below figure. (2) Open the dust box cover, take out filter HEPA in it, and then empty the debris and dirt in dust box.
Cleaning of Suction Mouth (1) Firstly, turn off robot cleaner. (2) Clean up the dust and dirt accumulated in suction mouth. Clean matters up the rolling Clean the foreign at thebrush dust suction port Cleaning of Side Brush （ 1 ） Turn off the switch of robot cleaner, place the bottom of robot cleaner on the flat ground or desktop, hold the side brush tightly and pull it up to remove it.
5. Analysis of Product Faults 1.The robot cleaner can not work or the cleaning ability is weakened (1). Check whether the switch of robot cleaner is on. (2). Check whether the dust box is clean and whether the side brushes are good (3). Check whether the voltage of battery drops seriously. (4). Check whether HEPA in the dust box is blocked by foreign matters 2. The robot cannot be charged (1).
Warnings about battery You must not remove (or attempt to remove) the battery incorporated in this product On your own.To replace the battery, your must contact your service provider or an independent qualified professional.These instructions have been prepared for the exclusive use of your service. Provider or independent qualified professional. FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO REMOVE THE BATTERY ON YOUR OWN OR DISPOSE PF IT IN FIRE.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
