HUGO BOSS WATCHES OPERATING INSTRUCTIONS, CARE & MAINTENANCE, AND WARRANTY & SERVICE INFORMATION
HUGO BOSS WATCHES Hugo Boss has a unique heritage in the fashion market. Developed with the meticulous attention to function and detail, the water-resistant Hugo Boss watch collection offers easy, elegant designs that reflect Hugo Boss’ style codes and trademark logo – one of the most recognized brand symbols in the world. Congratulations on your purchase.
(1) 2- AND 3-HAND MODELS M H M M H H S 1 –2 Figure A Figure C M H 1 –2 S Figure B Legend 1, 2 – Crown positions H – Hour hand M – Minute hand S – Second hand Crown Positions: Position 1 - Normal position. Crown pushed into case. Position 2 - To set TIME: Rotate crown in either direction. NOTE: When setting the minute hand, advance it 4 to 5 minutes ahead of the desired time and then turn it back to the exact time.
(2) DATE/DAY-DATE MODELS CAUTION: Never set the date when the hands are between 9:00 PM and 3:00 AM. Doing so could damage the calendar mechanism. M H NOTE: The functioning of the watch is not affected during date setting. When the watch is running, the date will change gradually during the period from 9:00 PM to 3:00 AM. Power depletion warning function: When the battery nears its end, the second hand moves at two-second intervals instead of the normal one-second intervals.
(3) DUAL-TIME MODELS - TYPE A W ith rotating reflectoring, GMT 24-hour hand and date hands, while left-mounted Dual time hand indicates dual time hours. After changing the battery, before setting the time, check if the dual time hour hand and dual time minute hand are at «0» (12 o’clock position). If either the dual time hour hand or the dual time minute hand is not in the «0» position, reset it/them with the following procedure: A H M F 1. 2. 1 –2 –3 B Z 3.
(3) DUAL-TIME MODELS - TYPE B Dual-Time with 24-hour hand and date hands, while left-mounted Dual time hand indicates dual time hours. After changing the battery, before setting the time, check if the dual time hour hand and dual time minute hand are at «0» (12 o’clock position). If either the dual time hour hand or the dual time minute hand is not in the «0» position, reset it/them with the following procedure: A H M F 1. 2. 1 –2 –3 B Z 3.
(4) MULTI-EYE MODELS – TYPE A W ith day/date with or without 24-hour hand without pushers M M H H J J 1 –2 – 3 1 –2 – 3 S D S T T Figure A Figure C D To set the time: 1. Pull crown out to position 3 when the second hand is at the 12 o’clock position, watch stops. 2. Turn crown clockwise to advance the hour and minute hands until the day hand is set to the desired day of the week, if applicable for your model. The day hand will not move back by turning the crown counterclockwise. 3.
(4) MULTI-EYE MODELS – TYPE B W ith day/date with retrograde sub-eyes without pushers To set the time: 1. Pull crown out to position 3 when the second hand is at the 12 o’clock position, watch stops. 2. Turn crown clockwise to advance the hour and minute hands until the day hand is set to the desired day of the week, if applicable for your model. The day hand will not move back by turning the crown counterclockwise. 3. Turn crown in either direction to move hands to desired time.
(5) MULTI-EYE MODELS – TYPE C W ith day/date with or without 24-hours hand with pushers M H A D J 1 – 2 B S T Figure A Legend 1, 2 – Crown positions A – Push button to set the day B – Push button to set the date H – Hour hand M – Minute hand S – Second hand T – Date hand J– 24-hour hand D – Day hand Crown Positions: Position 1 - Normal position. Crown pushed into case. Position 2 - To set TIME: Rotate crown in either direction. To set the time: 1.
(6) ANALOG CHRONOGRAPHS – TYPE A W ith day/date/24-hour hand correct time. J H To set the date (if applicable): If your watch has a date window, your crown will have 3 positions. Position 2 is used to set the date: 1. Pull crown out to position 2. 2. Turn crown clockwise until the correct date appears. M A P Crown Position 3 is used to set the time as per above explanation. 1– 2 – 3 S K Simple Chronograph Functions: To measure the duration of a single, non-stop event (up to 60 minutes): 1.
(6) ANALOG CHRONOGRAPHS – TYPE B W ith day/date/24-hour hand and retrograde sub-eye correct time. J H To set the date (if applicable): If your watch has a date window, your crown will have 3 positions. Position 2 is used to set the date: 1. Pull crown out to position 2. 2. Turn crown clockwise until the correct date appears. M A P Crown Position 3 is used to set the time as per above explanation.
(7) ANALOG CHRONOGRAPHS– TYPE C Chronographs 1/10 Second X To set the time: 1. Pull crown out to position 2 when the second hand is at the 12 o’clock position, watch stops. 2. Turn crown in either direction to move hands to desired time. If applicable for your model, make sure to respect AM/PM Do not press any button, otherwise the chronograph hands will move. 3. Push crown back in to position 1; watch restarts, now set to correct time.
(8) ANALOG CHRONOGRAPHS – TYPE C Chronograph with minutes and seconds hands and date 3. Press pushbutton A to resume measurement. 4. Repeat steps 2 and 3 to add each interval of time. NOTE: Each time you stop chronograph, chronograph hands will indicate total accumulated time. 5. After final reading, push button B to reset chronograph hands. M Q A Measuring Split Times: To take intermediate time readings as an event progresses: 1. Push button A to start timing. 2.
(9) AUTOMATIC W ith or without 24-hour hand To set the time: 1. Pull crown out to position 2. 2. Turn crown in either direction to move hands to desired time. 3. Push crown back in to position 1; watch restarts, now set to correct time. *(24-hour hand moves linked with the center Hour and Minute hand). M H 1 –2 S Figure A M H 1 –2 J S Figure B Legend 1, 2 – Crown positions H – Hour hand M – Minute hand S– Second hand J – 24 hours hand Crown Positions: Position 1 - Normal position.
(9) SPECIAL FEATURES SCREW DOWN CROW N A B Some models are equipped with a special screw-down crown that helps seal the case against water and moisture. Before attempting to set the time or date, you must first unlock the screw-down crown by turning it counterclockwise until it loosens (approximately six rotations). Unlocking is not required with standard crowns. A. To unlock the crown: Rotate the crown counterclockwise (left) until it releases from the case. B.
(9) SPECIAL FEATURES MESH BRACELET SLIDING CLASP The mesh bracelets found on select models feature a hooking jewelry clasp that allows you to size the bracelet by sliding the pin-bar half of the clasp along the bracelet to achieve a customized fit. Above: Open mesh bracelet side with pin-bar half of sliding clasp locked in position. To size the bracelet: 1. Use tool such as a small flat-head screwdriver to pop open metal plate on pin-bar half of clasp, releasing the clasp position locking mechanism. 2.
CARE AND MAINTENANCE Your HUGO BOSS WATCH has been developed with meticulous attention to quality, function and detail. Please read the following information and instructions carefully to learn about the features, proper care and operation of your new timepiece. For additional information on service and repairs, please see the Service and Warranty section. Never open the watch yourself. If your watch needs repair or adjustment, take or mail it directly to an authorized Service Center.
CARE AND MAINTENANCE NOTE: Frequent use of special functions, like the stopwatch timer on chronograph models, may shorten battery life. End-of-life feature: The second hand on many models will start to move haltingly in 2 or 4 second increments when the battery is almost exhausted, signaling the need to have it replaced. Battery replacement: Take or send your watch to an Authorized Service Center to have battery changed – your old battery will be disposed of/recycled properly.
WARRANTY INFORMATION WARRANTY INFORMATION Not only is each Hugo Boss watch beautiful in design, it is crafted with quality materials and components to offer precise, reliable performance. We proudly stand behind every Hugo Boss watch we sell.
OBTAINING SERVICE Should your HUGO BOSSwatch require service or repair, you may take it to an Authorized HUGO BOSS Watches Dealer, or mail it directly to one of the HUGO BOSS Watches Authorized Service Centers found on this website – just return to the HUGO BOSS Watches service website home page and click on the Warranty and Service Information link. Be sure to include your complete return address and phone number along with a brief note describing the problem with your watch and/or service needed.
