Installation Instructions
Table Of Contents
- Title page
- Contents
- About this manual
- Safety information
- Ch 1 - Introduction
- Ch 2 - Adding cards to the Controller
- Unpacking the System Controller
- Unpacking the picocells
- System Controller card configuration
- Adding cards to the System Controller (first steps)
- Jumper and DIP switch settings
- Attaching bus cables
- Adding cards to the System Controller (final steps)
- Configuring Controller cards
- Verifying the card configuration
- Ch 3 - Installing the Controller
- Ch 4 - Verifying the Controller configuration
- Ch 5 - Configuring the router
- Ch 6 - Testing picocells
- Ch 7 - Installing picocells
- Ch 8 - Connecting to external equipment
- Ch 9 - System testing
- Ch 10 - Installation inspection
- Ch 11 - Provisioning
- Ch 12 - Remote Client
- Ch 13 - Troubleshooting
- Ch 14 - Maintaining Quad T1 cards
- App A - Specifications
- App B - Standards compliance information
- App C - Part numbers
- App D - Updates and backups
- Index
1026209–0001 Revision BIndex-4
serial numbers, 2–7, 4–15
slots, numbering, 6–24
specifications, A–4
electrical, A–5
environmental, A–5
RF levels, A–6
weight, A–4
T1 wiring, 7–16
testing, 6–1, 6–17, 6–24
transceivers, 1–7
troubleshooting, 13–2
unpacking, 2–4
wiring flip, 7–16
pinouts, 7–17
Pin assignments
T1 cable for picocells, 7–8
wiring flip, 7–17
Pinging the gateway, 5–8
Ports. See Connectors
Power requirements
Controller, 3–6, A–2
picocell, 6–4
Power supply, picocells, 1–7, 1–12, 6–2,
6–4, 7–1, B–4
specifications, A–6
Programming mobile phones, 6–26
Programming test phones, 6–22
Provisioning
subscribers, 11–1
test mobile phones, 6–20
Q
Quad T1 cards
adding to Controller configuration, 2–30
bus adapter card, 2–23
configuring, 14–6
deleting, 14–9
DIP switch settings, 2–13
H.100 bus, 2–13, 2–23
cable, 14–2
jumper settings, 2–14
LEDs, 6–6
illustrated, 6–7
MVIP bus, 2–14
cable, 14–2
ports, illustrated, 6–4
removing, 14–9
replacing, 14–2, 14–5
T1 line settings, 2–30, 4–5
Quality inspection of installation, 10–1
R
Rack mounting
Controller, 3–4
illustrated, 1–4, 3–3
Registering test mobile phones, 6–23
Remote access. See Remote Client
Remote Client, 1–2, 12–1
installing, 12–2
requirements, 12–1
testing, 12–3
Removing a Quad T1 card, 14–9
Replacing a Quad T1 card, 14–2, 14–5
Repointing the HLR, 8–8
Restoring databases, D–3
RF coverage, testing, 9–1
RF levels, A–6
RJ–45 connectors
pinouts for wiring flip, 7–17
T1 cable for picocells, 7–8
Router
configuration example, 5–5
configuring, 5–2
installing, 5–2
supported model, 5–1
S
Safety information, xv, B–2, B–3
SBC (single board computer)
DIP switch settings, 2–20
jumper settings, 2–20
Scanning picocells, checking operation, 6–6
Scanning receiver (picocells), 1–7
Serial numbers, picocells, 2–7, 4–15
Service provider ID list, 8–13
Setup mode (Controller), 6–10
SID/PSID/RSID (system identification), 4–9,
6–21, 6–23, 6–26
Slots. See Controller, slots, and Picocell, slots
Specifications, A–1
Controller, A–1
picocells, A–4
SSL certificate, 8–4
example, 8–6