Installation Instructions
Table Of Contents
- Title page
- Contents
- About this manual
- Safety information
- Ch 1 - Introduction
- Ch 2 - Adding cards to the Controller
- Unpacking the System Controller
- Unpacking the picocells
- System Controller card configuration
- Adding cards to the System Controller (first steps)
- Jumper and DIP switch settings
- Attaching bus cables
- Adding cards to the System Controller (final steps)
- Configuring Controller cards
- Verifying the card configuration
- Ch 3 - Installing the Controller
- Ch 4 - Verifying the Controller configuration
- Ch 5 - Configuring the router
- Ch 6 - Testing picocells
- Ch 7 - Installing picocells
- Ch 8 - Connecting to external equipment
- Ch 9 - System testing
- Ch 10 - Installation inspection
- Ch 11 - Provisioning
- Ch 12 - Remote Client
- Ch 13 - Troubleshooting
- Ch 14 - Maintaining Quad T1 cards
- App A - Specifications
- App B - Standards compliance information
- App C - Part numbers
- App D - Updates and backups
- Index
1026209–0001 Revision Bx
7-9 Power terminal block connections 7–14. . . . . . . . . . . . . . . . . . . . . . . . . . .
7-10 Picocell connections at the telco closet 7–15. . . . . . . . . . . . . . . . . . . . . .
7-11 T568B–compliant wiring flip at patch panel 7–16. . . . . . . . . . . . . . . . . .
7-12 T568B–compliant wiring flip using modular jack 7–17. . . . . . . . . . . . . .
8-1 Example of a signed SSL certificate 8–6. . . . . . . . . . . . . . . . . . . . . . . . .
13-1 LEDs on front of picocell 13–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-1 H.100 and MVIP bus cables 14–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-2 MVIP bus adapter card 14–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables
2-1 Jumper settings for TX2000 IP and TX2000 SS7 cards 2–16. . . . . . . . . .
2-2 TX2000 card I/O address settings (switch S1) 2–17. . . . . . . . . . . . . . . . .
2-3 Conference card I/O address settings (switch S1) 2–19. . . . . . . . . . . . . .
2-5 SBC processor settings (switch SW1) 2–21. . . . . . . . . . . . . . . . . . . . . . . .
2-6 SBC card jumper settings 2–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1 Approved mounting plate fasteners 7–4. . . . . . . . . . . . . . . . . . . . . . . . .
7-2 T1 (RJ–45) connector pinouts 7–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3 Power supply and CAT 5 wire colors 7–14. . . . . . . . . . . . . . . . . . . . . . . .
13-1 Picocell alarms 13–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-1 System Controller environmental specifications A–3. . . . . . . . . . . . . . .
A-2 Picocell environmental specifications A–5. . . . . . . . . . . . . . . . . . . . . . .
A-3 Power supply environmental specifications A–6. . . . . . . . . . . . . . . . . . .
C-1 Major AIReach OS components, FRUs, and installation parts C–1. . . .