Portable System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. WARNING! READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. REQUIRED TOOLS AND MATERIALS: • • • • • • • • Two People Wood Board (Scrap) Tape Measure Step Ladder 8 ft. (2.4 m) Tape Garden Hose or Sand 360 lb.
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés).
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside.
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury.
Get to know the basic parts of your basketball system.....
PARTS LIST - See Hardware Identifier ItemQty. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ItemQty. Part No. Description 1 206657 Tank, (Black) 1 200628 Wheel Axle 2 226401 Wheel, 4“ (Black) 1 90021701 Top Pole Section 1 904840 Middle Pole Section 1 900136 Bottom Pole Section 1 202820 Rod, 3/8 O.D.
HARDWARE IDENTIFIER (BOLTS) Item #32 (2) Item #8 (1) Item #43 (5) Item #11 (1) Item #31 (4) Item #15 (2) Item #35 (1) Item #47 (1) Item #34 (1) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #37 (1) Item #39 (5) Item #18 (2) Item #12 (6) Item #38 (1) Item #9 (1) Item #13 (1) Item #36 (1) Item #16 (8) Item #40 (1) * You may have extra parts with this model.
HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #7 (1) Item #33 (2) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #42 (4) Item #20 (12) Item #49 (1) Item #17 (4) HARDWARE IDENTIFIER (OTHER) Item #48 (1) Item #46 (1) Item #45 (1) Item #30 (1) 9 01/05 P/N 211022
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION (not actual size) TOOLS REQUIRED FOR THIS SECTION Item #35 (2) 1/2”, (2) 9/16" AND (2) 3/4" Wrenches Item #33 Item #42 Item #34 Item #8 Item #39 AND/OR (2) Socket Wrenches and Sockets Item #7 Item #11 Item #15 Item #9 Item #30 Item #18 Item #17 Item #13 Item #16 Item #12 1/2” 9/16” 3/4” Item #43 P/N 211022 01/05 10 Item #49
1. 2. Remove contents from tank (1). 1 Correctly identify each pole section and mark indicated distance from ends with tape as shown.
3. IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce pole top (4) and middle section (5) together as shown until they no longer move toward taped reference mark. Upright assembly. 5 NOTE: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. 4 WOOD SCRAP (NOT SUPPLIED) 4. IMPORTANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 3.
5. 6 Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 8 6. Install wheel axle (2) through wheel carriage (19) and install wheels (3) onto wheel axle (2) with spacers (17) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) section to tank and wheel carriage as shown. A deep socket is recommended. WARNING! 6 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
7. Secure base struts (10) to pole using bolt (11), washers (12), and nut (13), as shown. Rotate the non-secured ends of base struts (10) as shown. 12 12 13 6 11 10 6 10 1 10 8. Secure base struts (10) to base using bolt (15), washers (12), and nut (16).
9. Fit spacer (33) into pawl (27). Then continue to assemble as shown. Tighten completely. 36 29 37 33 33 34 27 35 10. Identify elevator tubes (43 & 40).
11. Assemble elevator tubes (44) to ratchet (28) and backboard brackets (29) using bolts (43), spacers (42. 17, & 49), and nuts (32) as shown. Tighten completely. 27 39 29 42 39 49 44 17 42 28 43 17 IMPORTANT!: LEVER 43 44 12. Secure pawl (27) in place with clevis pin (30) and washers (18) as shown. BROOM HANDLE 13. It is necessary for all parts to be installed properly for this mechanism to work safely and properly. Stretch spring (41) into position with pliers.
SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION (not actual size) TOOLS REQUIRED FOR THIS SECTION (2) 1/2”, (2) 9/16"” AND (2) 3/4” Wrenches Item #16 Item #31 (4) AND/OR (2) Socket Wrenches and Sockets Item #46 Item #32 (2) Item #39 (5) Item #20 1/2” 9/16” Item #38 3/4” Item #42 Item #43 17 01/05 P/N 211022
1. Bend upper halves of backboard brackets (29) to line up with holes in backboard and secure with bolts (32) and nuts (16). Attach rim (21) and plastic spacer ( ) to board with bolts (31) as shown. 29 Tighten completely. 16 16 44 46 32 32 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 2. 21 31 Attach upper elevator tubes (44) to backboard brackets (29) using spacers (42) bolt (43) and nut (39) as shown.
3. Support pole on sawhorse. Attach upper and lower elevator tubes (44) to upper pole section (4) using bolts (43) and nuts (39) as shown. Attach pole cap (22) as shown. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
5. Install net clips. WARNING! CLIP “ARM” USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. CLIP “BODY” 21 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. 20 A Push second “arm” back and into ram as shown.
NET INSTALLATION 6. 21 SIDE VIEW 26 20 NETCLIP NET Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip.
7. Roll the completed assembly to the desired playing area. Insert the T-strap (14) through the slot on the back of the base as shown. Secure the unit to ground by twisting the tie down stake (23) into the ground and hooking the T-strap (14) onto the tie down stake (23). Fill tank with 33 gallons of water. 24 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
