Portable System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. WARNING! REQUIRED TOOLS AND MATERIALS: • • • • READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. • • • • • • • • FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés).
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside.
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury.
Get to know the basic parts of your basketball system.....
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 2 1 1 1 1 1 1 1 2 1 7 1 206336 206330 226401 904847 908024 908487 202820 202822 202821 203063 906410 203220 203218 201625 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 2 9* 1 2 4 4* 4 2 2 2 1 1 1 1 1 2 203798 203100 204832 203231 203232 201124 206360 204858 204857 204859 203038 204850 204853 904833 204872 203103 Item Qty. Part No.
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #31 (1) Item #8 (1) Item #30 (2) Item #14 (1) Item #25 (1) Item #48 (1) Item #47 (6) Item #21 (4) Item #18 (2) Item #15 (2) Item #55 (4)* * You may have extra parts with this model.
HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #2 (2) Item #36 (2) Item #7 (1) Item #23 (2) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #44 (2) Item #22 (2) Item #57 (4) Item #50 (12) Item #38 (4) 9 01/04 P/N 211955E
1. Remove all contents from underside of tank. Keep tank (1) bottom side up 2. 1 Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 3 2 1 3. Mark pole sections with tape as shown.
4. IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. 5 NOTE: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. 4 WOOD SCRAP (NOT SUPPLIED) 5.
6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 4 5 6 8 7. Insert pole assembly into tank assembly as shown. 6 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 7 8 IMPORTANT!: DO NOT OVER TIGHTEN 8. Carefully place unit on its side. Secure pole bottom (6) to tank with anchor strap (52), washers (9 & 13) and nut (10) as shown. Upright unit.
9. Secure strut tubes (11) to bottom pole section (6) as shown. WARNING! 11 6 13 14 12 TIGHTEN BOLT (14) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. 11 1 10. 13 11. Carefully place unit in the side position and secure strut (11) to tank (1) as shown. Completely tighten. Repeat for opposite side. Upright unit. Install pole mount bracket (17) and reinforcement bracket (37) with carriage bolts (18) as shown. Tighten flange nuts (16) completely.
12. Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), and nuts (20) as shown. IMPORTANT!: Tighten just until washers (19) stop moving. 17 22 20 23 19 20 19 21 19 23 19 22 13. 21 Assemble lanyard (27) to locking pin (26) as shown (FIG A). Attach covers (24) onto pole mount bracket (17) with carriage bolt (25) and nut (16) as shown. FIG.
14. Apply logo and height indicator labels (29) to adjustment rod (28) as shown. Attach handle parts (32, 33) to adjustment rod with screw (31), carriage bolt (30), and flange nut (16) as shown. 15. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (26). IMPORTANT!: Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment.
. Attach backboard support brackets (34) to the backboard frame using bolts (21), spacers (36), and nuts (20) as shown.
. Attach rim to board as shown. For spring loaded rim assembly, refer to instructions included with rim hardware. Assemble lower elevator tubes (40) as shown. DO NOT overtighten. 34 39 57 57 47 41 40 40 42 55 IMPORTANT!: IMPORTANT!: Refer to instructions included with board and rim hardware for backboard and rim assembly. It is necessary for all parts to be installed for this mechanism to work safely and properly.
. Assemble upper elevator tubes (43) to backboard brackets (34). DO NOT overtighten. 39 34 57 43 57 47 41 43 19. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46). WARNING! USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
20. Install upper elevator tubes (43) to triangle plates (45) as shown. 39 43 38 40 NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 45 40 38 IMPORTANT!: 47 DO NOT OVER TIGHTEN 43 28 44 Then, install handle assembly to lower elevator tubes (40) using bolt (47), spacers (44), and nut (39) as shown.
21. Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39). 43 39 47 41 43 WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 22. Roll completed assembly to desired position. Secure assembly to ground using anchor strap (52) and tie down stake (53). Fill tank with water (approx. 30 gallons /115 Liters) or sand (approx. 255 lbs./113 kg) and snap cap (49) in place.
23. 24. 25. 26. While holding handle, remove pin (26). Apply height and transport label (54) to front of pole as shown. Move elevator up or down to desired height. NOTE: Replace pin (26) full length to lock system at desired height. Peel protective film from surface of acrylic backboard prior to use. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. 10. 26 54 12. 10 ft. (3.05 m) 11.
27. Install front cover (35) onto struts (11) as shown. 35 11 28. Loop zip tie (56) around strut (11) and cover (35). Pull flat end of zip tie (56) through square end of zip tie until completely tightened. 29. NOTE: Ridges on zip tie (56) should be on inside of loop when pulling flat end of tie through square end. 56 56 11 35 P/N 211955E 01/04 22 Once fully secured in the four areas shown, trim excess of zip tie (56) with scissors.
30. Install net clips. WARNING: Installez les pinces du filet. Netzhalteklammern anbringen. Instale los sujetadores de la red. Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. CLIP “ARM” AVERTISSEMENT ! WARNUNG! ¡ADVERTENCIA! L'UTILISATION DE CE PRODUIT SANS L'INSTALLATION CORRECTE DES SMART CLIPS® OU EN L'ABSENCE DE CERTAINES SMART CLIPS® EXPOSE LES JOUEURS À DES BLESSURES.
NET INSTALLATION 31. 42 Install net. SIDE VIEW Installez le filet. VUE DE CÔTÉ SEITENANSICHT VISTA LATERAL NETCLIP PINCE DE FILET NETZHALTEKLAMMER SUJETADOR DE LA RED Das Netz anbringen Instale la red. 51 50 NET FILET NETZ RED Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del sujetador como se muestra. Twist net until it snaps into position.
