Instructions / Assembly

ManualsBrandsHuffy ManualsOutdoor SportsTonka Yellow Bubble Scooter 6-Volt Battery Powered Kids Ride-On

[ In the US and Canada]

PLEASE - BEFORE RETURNING TO STORE:

Contact Hu y Customer Service. We

are glad to assist you with any parts or

assembly problems you might have!

VEUILLEZ NOTER : AVANT DE

RETOURNER AU MAGASIN :

Communiquez Avec Le Service À La

Clientèle De Hu y. Nous Vous Aiderons

Volontiers Avec Tout Problème Concernant

Les Pièces Ou Le Montage!

For Fast Customer Service, go to:

Pour un Service à la clientèle rapide, allez sur le site :

http://www.hu ybikes.com/contact

To Order Parts (US), go to:

Pour obtenir des pièces (CANADA), allez à:

http://www.hu ybikes.com/parts

OR TEL: 1 800 872 2453 (US only)

OU appelez le 1 800 872 2453 (CANADA seulement)

For email, go to http://www.hu ybikes.com/contact

Pour communiquer par courriel hu ycanada@hu y.com

[ MÉXICO ]

ANTES DE DEVOLVER EL

PRODUCTO A LA TIENDA:

Comuníquese Con Servicio Al

Cliente De Hu y. Nos Complace

Ayudarlo Con Cualquier Parte

O Problema De Ensamblado

Que Pudiera Tener.

Para obtener Servicio al cliente

rápido, visite:

http://www.hu ybikes.com/

O LLAME AL TEL: 01800 1483 391

(Mexico only)

Para comunicarse por correo electrónico:

servicio@hu ymex.com

H-Tri_STOP-Global_010318_i0388

For Assembly Help:

Ayuda de la Asamblea:

Aide à l’assemblage :

http://www.hu ybikes.com/home/globalcontact

for current contact information

para obtener la información de contacto actual

pour les informations de contact actuelles

See back page for Customer Service Information

Consulte el reverso para Servicio de Información al Cliente

Voir pages verso pour des renseignements le service à la Clientèle

Owner’s Manual

Battery Ride-On

Bubble Scooter

Date Code Label

Here

H-Bub eScooter_EN 09-28-18 m0414

This manual contains important safety,

assembly, operation and maintenance

information.

Please read and fully understand this

manual before operation.

Save this manual for future reference.

Summary of content (10 pages)

PAGE 1
H-Bub eScooter_EN 09-28-18 m0414 Date Code Label Here [ In the US and Canada] PLEASE - BEFORE RETURNING TO STORE: Owner’s Manual Contact Huffy Customer Service. We are glad to assist you with any parts or assembly problems you might have! ~ VEUILLEZ NOTER : AVANT DE RETOURNER AU MAGASIN : Comuníquese Con Servicio Al Cliente De Huffy. Nos Complace Ayudarlo Con Cualquier Parte O Problema De Ensamblado Que Pudiera Tener. Para obtener Servicio al cliente rápido, visite: http://www.huffybikes.
PAGE 2
Owner’s Manual Index Safety • User and Battery Warnings ...............................................................................................3-4 • Radio Frequency ....................................................................................................................4 • Charging Drive Motor Warnings.......................................................................................5 Assembly • Parts Assembly...........................................................................
PAGE 3
Limited Warranty - US Warranty What does this Limited Warranty cover? This Limited Warranty covers defects in workmanship and materials for all parts of the product except those indicated below as not warranted. What must you do to keep the Limited Warranty in effect? This Limited Warranty is effective only if: • Product is completely and correctly assembled. • Product is used under normal conditions for its intended purpose (see the following section for excluded activities).
PAGE 4
WARNING: ALWAYS WEAR YOUR HELMET WHEN RIDING THIS PRODUCT! • Helmet should sit level on your head and low on your forehead. Exposed forehead can result in serious injury. • Adjust the strap sliders below the ear on both sides. • Buckle the chin strap. Adjust strap until it is snug. • No more than two fingers should fit between the strap and your chin. • A proper fitting helmet should be comfortable and not rock forward/backward or side to side.
PAGE 5
Troubleshooting NOTE: Vehicle should be turned off and fully changed before doing troubleshooting. Problem Possible Cause Solution Vehicle does not run when switch is activated Battery wires not connected or are loose Connect battery wires according to assembly instructions, Check that the battery connectors are firmly plugged into each other. If wires are loose around the motor call Customer Service.
PAGE 6
Parts View Drive Motor Battery Battery Fuse 8 7 6 WARNING: DO NOT BYPASS THE FUSE - RISK OF FIRE. This may overload and damage the electrical system. Battery Re-charge Interval and Time IMPORTANT! 6 10 13 12 Check the drive battery and charger (supply cord, connector) for wear and damage before charging. Do not charge the battery if damage has occurred. Only replace with the same type and voltage rechargeable battery and charger supplied by the manufacturer.
PAGE 7
1. 2. Parts List Turn Scooter on it’s Side. Remove the Battery Cover and Screws . 3. Remove the Battery Bracket A and Screws . D 4. Disconnect the Red and Black Battery Terminals . 5. Carefully remove the Battery. • Depending on the condition of the battery (leakage or C damage) you may want to wear protective rubber gloves before removal. • Do not lift the battery by its connectors or cables. B 6. Place the dead battery in a plastic bag. 7.
PAGE 8
Assembly This Owner’s Manual may be made for several different style products. • Some illustrations may vary slightly from the actual product. • Follow instructions completely. • If the product has any parts that are not described in this manual, look for separate “Special Instructions” that are supplied with the unit. • All features, components and accessories are not included on all models. • Use the Index page to locate specific sections of this manual.
PAGE 9
Operation: Installing Rear Wheels: USAGE: • Turn ON Scooter power by holding down Power Button . Release Power Button to stop. • Push Motor Engage-Lever DOWN to engage motor and UP to disengage motor. A A B Assembly Operation A NOTE: Disengaging Motor allows scooter to be selfpropelled. TO USE BUBBLE MAKER: D CAUTION: Fill ONLY with solution designated on the product: C E F B C D C • Pull out Fill Tray as shown (Drawer is not removable), to fill with Bubble solution. Do Not Overfill.
PAGE 10
Assembling the Front Wheel and Handlebar: Handlebar Connectors and Clamp Cover Assembly: STEPS: Ensure Power Button A and Wiring Connector are facing BACK. 2. Insert Steering Rod down through Neck frame. 3. Ensure top and bottom Neck Bushings are fully inserted into Neck frame and sit fully in Notches E. 4. Place Fender over Fork Assembly . 5. Insert this Fork Assembly up onto Steering Rod fully so that Fork mounting holes line up. 6. Install Fork Screw Set through Fork assembly and Steering Rod.