User's Manual

ManualsBrandsHuey Chiao Internatinal ManualsAudio EquipmentBluetooth stereo headset

Bluetooth Stereo Headset

HS899 User Guide

Notice before using

Thank you for purchasing our Bluetooth Stereo Headset

HS899. First of all, please check the items in your package

and carefully study the user guide to know the function details.

HS899 is developed by the innovative Bluetooth wireless

technology, enabled to connect the Bluetooth mobile phone/

audio devices with Stereo Gateway (HS809/819/829/839)or

any Bluetooth device which is with Bluetooth V1.1/V1.2/V2.0

and supports Bluetooth A2DP and AVRCP (Audio Advance

Distribution Prole).

Package List

Please check the product you purchased. Refer to the below

package list to make sure there is no shortage or defect inside.

The complete package includes the following items:

◆

HS899 / Bluetooth Stereo Headset .............................1

◆

User Guide ................................................................. 1

◆Warranty Card

.............................................................. 1

◆

Two in one Charger (travel charger head +USB Cable,

input:AC100-240V,50/60Hz, output: DC5.1V,120mA) .. 1

If you nd any shortage, please contact the retailer shop which

you purchase this product from.

1 2

Plug the travel charger into the AC outlet and then connect

the charger into the DC input of the HS899 unit. The red

indicator will illuminate. When the battery is fully charged,

the red indicator will be switched off. Remember to charge

the headset for 4 hours before using it for the first time.

Subsequent charging times will take approximately 2 hours to

fully charge the battery.

Low-battery indication

When low battery, indicator shows slow red ash instead of

slow blue ash

Headset Overview

Charging the battery

Turning ON/OFF the headset

Press the button( ) for 3 seconds. The blue indicator will

be begun to ash. A short "Du----" tone can be heard. The

headset is turned on.

Press the button( ) again for 3 seconds. A "Du---BI---",

tone can be heard. The headset is turned off.

Pairing the headset

1. Ensuring the headset is initially switched OFF. Turn on the

headset, and then press the button( ) for 5-6 seconds until

the blue and red indicator begin to ash alternately.

The headset is now in pairing mode. Initiate the pairing

process on your Bluetooth mobile phone.(Please refer to

your mobile phone manual for more information.)

2. When asking for the pin-code, please enter "0000" to

successfully complete the pairing process.

3. If the pairing is not established over a period of approx..1

minute, the pairing process will be terminated. Please

repeat the pairing process.

4. Pairing up with PC/NB & mobile phone: If you are going

to combine the music listening from the PC/NB with this

stereo headset, please pair up with the PC/NB first, after

that, please pair up with the mobile phone Same

Receiving and ending calls

1. Press the button( ) to answer a call.

2. Press the button ( ) again to end the call.

Last number redial

To redial the last outgoing call, press button ( ) for 3 seconds

until a beep tone is heard then release ( This function is

subject to the settings of the mobile phone. Please refer to the

mobile phone manual for further information).

Voice-dialing

To active the voice-dialing function, press the button ( ) then

release once a beep tone is heard. (This function is subjected

to the setting of the mobile phone. Please refer to your mobile

phone manual for further information.

Rejecting a call

To reject an incoming call, press the button( ) for 3 seconds

until a beep tone is heard.

Transferring a call

Press button ( ) for 3 seconds to transfer a call from the

mobile phone to the headset or from the headset back to the

mobile phone. (Press refer to your mobile phone user guide

for more information.)

12 13 14 15

Specication

Product Model No. : HS899

Frequency Band : 2.4GHz ~ 2.4835GHz, ISM Band

Talking / Standby Time : Up to 12 hours / Up to 120 hours

Supporting Prole : Headset & Handsfree Prole

(A2DP) (AVRCP)

Bluetooth Specication: Bluetooth V2.0 compliant, class II

Connection : Peer to peer

Data Encryption : 128 bits encrypted

Battery : Rechargeable Li-Polymer battery

Power Supply : 5V DC, 100-240V AC adapter

Operation Temperature: -10 ~ 55

℃

Storage Temperature: -20 ~ 60

℃

Operation Moisture: 10% ~ 90% (non-concrete status)

Weight : 87g

Size : 140mm(L)*96mm(W)*60mm(H)

Working Range: Outdoor 10 meters,indoor 5 meters

Safety regulation:CE FCC BQB RoHS

Remark:Transferring between incoming call and music

playing

When the mobile phone is playing music, the music will be

interrupted if there is an incoming callress the function button

to receive call.

When the call is end, the music will play automatically.

Wearing the headset

Connecting with a Bluetooth enable mobile phone

Optimal performance

Limited performance

15.21

You are cautioned that changes or modications not expressly

approved by the part responsible for compliance could void the

user’s authority to operate the equipment.

15.105(b)

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. How-

ever, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful inter-

ference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measurements:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for

help.

Federal Communications Commission

(FCC) Statement

Operation is subject to the following two conditions:

1) This device may not cause interference.

2) This device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. End users must follow the

specic operating instructions for satisfying RF exposure com-

pliance. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

indicator light

DC JACK

MIC

Putting HS899 in standby mode

Headset is in standby mode when in the below situations:

1.Already paired and power on.

2.When Completing pairing

3.After ending call

When headset is in standby mode, you can answer call without

re-power on.

Locally adjust volume on HS899

When talking, you can adjust volume by button V- (volume-

down) or button V+ (volume-up).

Remotely adjust volume by mobile phone

When talking, you can adjust headset volume remotely by

mobile phone’s volume key.

10m

Microphone

DC Input

Vol -: Volume-down

Vol+: Volume-up

: Music stop/pause/play

:Forward/Skip to next music track

:Backward/Skip to previous music track

:Turning ON or OFF/Pairing/Answer/Ending/Reject/

Redial/Voice-dialing

Note: The forward , backward , and play buttons

will only work with mobile phones that support AVRCP

prole. (Please contact your mobile phone manufacturer for

further information).

Connecting with a Bluetooth enable

PC, LAPTOP or PDA

1. Turn ON the headset. Press and hold the button ( ) on the

headset for 3 seconds until the blue and red indicator begin

to ash alternately. The headset is now in pairing mode.

2. Start your Bluetooth software / driver on your computer or

PDA to search for a Bluetooth device.

3. When prompted for a pairing pin-codes, please enter "8888".

4. Select "HS899" from the list of Bluetooth devices to

complete the pairing process.

5. Ensure the audio device settings are setup on your OS

system (e.g. Windows and MAC).

Note: To use the headset with VoIP software, please setup

the audio device settings on both your OS system (e.g.

Windows. Mac) and VoIP software (e.g. Skype ,MSN and

Yahoo Messenger etc.)

Listening to music

After successfully pairing the headset with your mobile phone,

you can play music from your mobile phone. An incoming

call will interrupt the music and the ring will be heard from

the headset.

Note: Make sure your mobile phone is with the music function

and Bluetooth A2DP, AVRCP profiles. (Please contact your

mobile phone manufacturer for further information).

When you are listening to the music from PC/NB, the music

will automatically cut down by the incoming phone. And the

music will play again once the phone is off.

Trouble- Shooting

1. Flashing red LED: Low battery power. Charge the battery

until the red LED is turned off.

2. Cannot turn OFF the headset/LED constantly on: Plug

the travel charger into the AC outlet and then connect the

charger into the DC input of the headset. This will reset to

the last operating status.

3. No connection between the headset and mobile phone.

Make sure that the headset or mobile phone is fully charged

and try again. Check if the mobile phone or headset has

been paired with other Bluetooth device.

1. Hold both sides of the headset and hook on to the ears from

the back of the head.

2. Gently adjust the headset to a comfortable position.

3S 3S 3S

* LED used in this product is leveled class I.