® Ages 14+ READ THE INSTRUCTION MANUAL CAREFULLY PLEASE VISIT WWW.HUBSAN TO UPGRADE THE HUBSAN X4 DESIRE ITEM NO.
COMPASS CALIBRATION BEFORE FLY Compass calibration is required after the binding as instructed on the transmitter. 1.) Rotate the X4 horizontally until the " Set Compass 2" displays on the screen. 2.) Put the X4 nose down and rotate it vertically until the " Set Compass 2 " disappears. 3.) Calibration done.
Hubsan X4 Desire Please read the instruction manual carefully! IMPORTANT SAFETY NOTES OPERATION: Be extremely careful and responsible when using the drone. Small electronic components can be damaged by crashing or by dropping the X4 into water. To avoid further damages, please replace broken parts immediately. Flight: Take responsiblity for the safety of yourself and others when flying the X4! Do not fly the X4 in crowded places. Do not fly in bad weather. Never try to catch the X4 while it is in flight.
INTRODUCTION Thank you for buying the HUBSAN product. It is designed as an easy-to-use,multi-functional RC model, capable of hovering and acrobatic flight maneuvers. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference. Quadcopter Weight: 155g(including battery) 1. ITEMS INCLUDED IN THE BOX Check all the items in the box before using.
2. QUAD COPTER MOTOR LED INDICATOR Indicator Status: Front LED: is blue; Back LED: is red. 1. Power on: 4 LED indicators blink simultaneously every 1.5 seconds. 2. Compass Calibration: 1). Horizontal calibration: 4 LED indicators blink circularly. 2). Vertical calibration: 4 LED indicators blink alternately. 3. GPS Flight: 4 LED indicators remain lighted. 4. GPS Return : 2 front LED remain lighted, and 2 back LED blink twice every second. 5. Photo: 2 front LED remain lighted, 2 back LED blink once. 6.
4. PROPELLER Attach the propellers to the corresponding motors that are marked A and B,tighten the propellers and keep the motors deadlocked with the screw-driver. Black screw A Silver screw B Tighten the A propeller with black screw; Tighten the B propeller with sliver screw. “I” Mark “D”Gap Match the “I” mark on propellers to the “D” gap on motor shafts when assembling, as figure 1 shows. ● Make sure that the A and B propellers are installed correctly.
5. START TO FLY 5.1 FLIGHT ENVIRONMENT (1) The flying area should be open and without tall buildings or other obstacles; the steel structure within buildings interferes the compass and the GPS signal. (2) DO NOT fly in bad weather such as strong wind, heavy snow, rain or fog. (3) Keep away from barriers, people, power cables, trees, and other obstructions. (4) Do NOT fly near radio towers or airports.
5.4 BASIC FLIGHT The operation mode for the transmitter including Mode 1 or Mode 2. The manual will use Mode 2 as an example to illustrate the transmitter’s operation. Transmitter (Model 2) X4 UP Remarks The throttle stick controls the ascent and descent . Push up the stick and the X4 will ascend. Pull down the stick and the X4 will descend. When the stick is in the center, the X4 will hover and hold its alititude automatically . Move the throttle stick above the center position to take off.
RTH RTH only available when there are no less than 6 GPS satellites displayed on transmitter. Press the RTH for 1.5 seconds to activate the function, press again to stop the RTH. GPS and RTH function only available outdoors. 5.5 PHOTO / VIDEO PHOTO / VIDEO SD Insert the SD card into quadcopter before using Photo/Video function. Press the Photo/Video button for 0.5 second to take photos. Press the Photo/Video button for 1.5 seconds to take videos and press again to save the videos.
6.2 RTH MODE (RETURN TO HOME) ENTER/ EXIT RTH MODE Press the RTH button for 1.5 seconds, and the drone will enter into RTH mode. The flight control system will control the drone to fly back to the home point and land automatically. Press the button again for 1.5 seconds to exit RTH mode. ! The RTH MODE only works when the GPS with no less than 6 satellites. 6.3 FAILSAFE MODE The drone will enter into Failsafe Mode when the connection is lost from the transmitter.
7.
7.1 INSTALL THE TX BATTERY PUSH PUSH Close the cover Install 4 x AAA batteries according to the correct polarities Remove the cover ● Do not mix old and new batteries ● Do not charge non-rechargeable battery. ● Do not mix different types of batteries 7.2 NORMAL AND EXPERT FLIGHT MODES The default setting for X4 is Normal Mode, and the Expert Mode can be activated to have a better sensitivity on the performance of the X4. Press the Elevator stick 0.
8. QUADCOPTER CALIBRATION 8.
9. TRANSMITTER CALIBRATION Mode 2: Push both sticks to the upper left corner and power on the transmitter simultaneously. The LCD will display “H”, rotate both sticks in circles for three times, then release both sticks, press any trim for 1.5 seconds until one “Beep” heard which indicates a successful calibration.
EXPLODED VIEW 20 34 31 20 14 31 21 13 21 34 4 32 12 12 22 5 33 26 28 28 9 16 10 24 15 24 25 30 26 28 28 30 28 10 11 33 24 9 28 27 27 3 25 28 24 26 25 25 26 23 2 8 28 19 29 19 29 29 29 29 30 29 29 29 6 1 29 6 18 30 19 30 17 29 19 29 14 ©2016 Hubsan
NO. PART NAME 15 ©2016 QTY NO. PART NAME Lower Body Shell Eye Lampshade 2.4 GHz Transmission Module Rubber Feet Main Control Board Propeller A Compass Module Propeller B GPS Module Signal Isolation Membrane Blue LED Battery Compartment Red LED Motor Holder Camera Module Rotary Gear Motor A Motor Gear Motor B Motor Shaft A Li-Po Battery Bearing Screw PB1.4*3 Screw PA1.4*7 2.4G Attenna Screw PA1.4*5 Upper Body Shell Screw PM1.4*5 GPS Shielding Case Screw PA1.
H502E SPARE PART CHART H502E-01 Body Shell Set H502-01 H502-02 H502E-02 Battery Cover Eye Lampshade Lens Holder H502-03 H502-04 Lamp Base A/B Screw Set H502-08 H502-20 H502E-06 H502-14 H502E-03 H502-05 H502-06 H502-07 Propeller A/B Motor A Motor B Motor Holder H502-10 H502-11 H502-12 H502-13 Motor Gear B Motor Shaft LED Kit 2.
FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
User manual is subject to change without prior notice due to unforseen product upgrades. Download the latest user manual from WWW.HUBSAN.COM VERSION 1.
