Installation Sheet

ManualsBrandsHubbardton Forge ManualsChandeliersSummer Single Light 54" Wide LED Abstract Linear Chandelier - Standard Variant

Assembly & Installation Instructions A433

Summer Pendant 139753D Page 1 of 4

Modern American Blacksmiths | Fine, Hand-Crafted Lighting

Castleton, Vermont USA | HUBBARDTONFORGE.COM 34942 Rev B

Attach Ceiling Brackets (Figures 1 & 2)

Component Parts

A Mounting bracket (2)

B Canopy

C Ground Nuts (2)

D Cupped Washer (2)

E #10 Wood Screws (8)

F #8 Screws (2)

G Safety Cable

H Safety Cable Nut

I Supply Cable (4)

J Threaded Standoffs (4)

K Barrel Knobs w/Studs (4)

L Connectors (2)

Caution: Be sure power is off at the main breaker box prior to installation.

1. Locate mounting brackets (A).

2. Using wood screws (E), attach mounting brackets (A) to a structural member in the ceiling, centering

the bracket over the outlet box. It may be necessary to pre-drill ¼” holes where screws (E) are being

installed. Wood screws are supplied with your fixture; however, different materials and/or construction

methods may require different fasteners. If in doubt, contact a qualified electrician. Do not attach

bracket directly to outlet box.

Note: There are half-round features build into the mounting brackets to help with alignment when installing both

brackets to the ceiling.

3. The blue and red wires on one end of the fixture will be attached to the driver with supplied connectors

(L). Run the long blue wire from one end of the mounting bracket (A) to the supplied connectors on

the black wire of the driver. Repeat same step for Red wire (connecting to the red driver wire). See

figure 2 for wiring diagram of connectors (L).

Note: Grey and purple driver wires are not used for this fixture.

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Summary of content (4 pages)

PAGE 1
Assembly & Installation Instructions A433 Summer Pendant 139753D Page 1 of 4 CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.* Caution: Do not exceed maximum wattage noted on fixture.
PAGE 2
Assembly & Installation Instructions A433 Summer Pendant 139753D Page 2 of 4 (Figure 1) 4. Raise canopy (B) close to ceiling and attach safety cable (G) using safety cable nut (H) that is shipped installed in the mounting bracket (A). Note: Safety cable is used to temporarily suspend canopy while wiring connections are made. 5. Using cupped washers (D) and ground nuts (C) that ship installed on the mounting bracket (A), run pigtail leads from both brackets to the outlet box.
PAGE 3
Assembly & Installation Instructions A433 Summer Pendant 139753D Page 3 of 4 10. Screw barrel knobs with studs (K) into threaded standoffs (J). 11. To completely secure canopy, thread #8 screws (F) through canopy (B) and into mounting brackets (A). To Install LED Assembly (Figure 3) Component Parts I M N O Supply Cable (4) LED Assembly Gripper (4) Gripper Cover (4) (Figure 3) 1.
PAGE 4
Assembly & Installation Instructions A433 Summer Pendant 139753D Page 4 of 4 To Complete Installation (Figure 4) Component Parts M LED Assembly P Tube Assembly Q Decorative Element (Glass or Textured panel) 1. Each decorative element (Q) has a small hole in one corner. Slip decorative element (Q), hole side first, through tube assembly (P) until it settles into the bottom of the tube (P). 2. Repeat with remaining decorative elements (Q). 3. Restore electricity at main breaker.