HUAWEI HG622 Home Gateway User Guide HUAWEI TECHNOLOGIES CO., LTD.
HUAWEI HG622 Home Gateway V100R001 User Guide Issue 02 Date 2010-06-25 Part Number 202193 Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters. Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website: http://www.huawei.com Email: terminal@huawei.
Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd and possible licensors.
Contents 1 Warnings and Precautions ....................................................................... 1 2 Connecting the Cables and Powering On................................................ 4 2.1 Simple Connection .......................................................................................4 2.2 Connecting One Telephone ..........................................................................5 2.3 Connecting Multiple Telephones .............................................................
7.2 Interfaces and Buttons................................................................................21 7.3 Default Settings..........................................................................................22 7.4 Technical Specifications.............................................................................
1 Warnings and Precautions To use the device properly and safely, read these warnings and precautions carefully and strictly observe them during operation. Unless otherwise specified, the term "device" refers to the device and its accessories. Basic Requirements z During storage, transportation, and operation of the device, keep it dry and prevent it from colliding with other objects. z Do not dismantle the device. In case of any fault, contact an authorized service center for assistance or repair.
Precautions for Using Wireless Devices z When using the device, ensure that the antenna of the device is at least 20 cm away from all persons. z Do not use the device where using wireless devices is prohibited or may cause interference or danger. z The radio waves generated by the device may interfere with the operation of electronic medical devices. If you are using any electrical medical device, contact its manufacturer for the restrictions on the use of the device.
Maintenance z If the device is not used for a long time, power it off, and then remove all the cables connected to it. z If any exception occurs, for example, if the device emits any smoke or unusual sound or smell, stop using the device immediately, power it off, remove all the cables connected to it, and then contact an authorized service center. z Do not trample, pull, or overbend any cable. Otherwise, the cable may get damaged, causing malfunction of the device.
2 Connecting the Cables and Powering On 2.1 Simple Connection If your telephone line is used for the broadband network access only and if you do not need to use a telephone, take the following figure as a reference for connecting the cables. 1 DSL LAN4 LAN3 LAN2 LAN1 RESET POWER 3 2 1. Telephone jack on the wall 2. Computer 3. Power adapter If the wireless network function is used on the HG622 for the network access, you do not need to connect the cables.
2.2 Connecting One Telephone If your telephone line is used for both the broadband network access and a telephone connection, take the following figure as a reference for connecting the cables. 1 DSL LAN4 LAN3 LAN2 LAN1 RESET POWER LINE 2 PHONE 5 MODEM 4 3 1. Telephone jack on the wall 2. Splitter 4. Computer 5. Power adapter 5 3.
2.3 Connecting Multiple Telephones If your telephone line is used for the broadband network access, telephone connections, and fax connections, take the following figure as a reference for connecting the cables. 1 DSL LAN4 LAN3 LAN2 LAN1 RESET POWER LINE 2 5 MODEM PHONE 4 3 3 7 1 6 8 7 1. Telephone jack on the wall 2. Splitter 3. Telephone 4. Computer 5. Power adapter 6. T connector 7. Microfilter 8.
2.4 Powering On To power on the HG622, press the ON/OFF button on the side panel of the HG622. After you power on the HG622, the DSL indicator blinks (for less than three minutes), which indicates that the HG622 is being activated. Later, the DSL indicator turns solid on. The POWER indicator is also solid on, which indicates that the HG622 is working properly. 3 Setting the Internet Access Parameters The HG622 supports VDSL2 uplink and High-Speed Packet Access (HSPA) uplink through Huawei HSPA data card.
Step 1 Click Advanced > PIN in the navigation tree to display the PIN Page. Step 2 Enter the original PIN number in the PIN text box. Step 3 Click the Submit button to finish the settings on the PIN Page. Use the default values for the other parameters. In general, they do not need to be configured. 3.
Step 4 Set LAN parameters. 1. In the navigation tree, choose Basic > LAN. 2. Set the IP address and Subnet mask of the LAN connection. 3. Select Enable for DHCP server, and then set the corresponding parameters. 4. Click Submit. After you complete the preceding settings, you can surf the Internet. You need to perform the preceding operations on a computer once only. The next time when you power on your computer, you can surf the Internet without any configuration.
You need to perform the preceding operations only once for creating a network connection. After the network connection is created, to access the network, double-click the icon for the dial-up connection, and then click Connect in the displayed dialog box. 4 Configuring Connection the Wireless Network If a wireless network adapter is installed on your computer, you can connect you computer to the HG622 through a wireless connection.
The WPS indicator of the HG622 becomes on from the blinking state, indicating that the HG622 is connected to your PC through the WLAN. This state lasts 300s. Then the WPS indicator turns off. If the WPS indicator does not blink, it indicates that the WPS function cannot be enabled. Note that the WPS function can be used only when the wireless network function is enabled and the wireless network security mode of the WLAN is set to WPA-PSK or WPA2-PSK.
5. Click OK to close the dialog box, and then close the Computer Management window. Step 3 Configure the wireless network connection on your computer. 1. Choose Start > All Programs > Accessories > Communications > Network Connections. 2. In the Network Connections window, right-click Wireless Network Connection to display a shortcut menu, and then select View Available Wireless Networks from the shortcut menu. 3. In the Wireless Network Connection Properties dialog box, select Wireless Networks. 4.
Step 5 Click Submit to save the settings. After you change the password successfully, the current page jumps to the page for logging in to the Web-based configuration utility. To log in to the Web-based configuration utility, enter the new password, and then click Submit. If you forget the user name or password that has been changed, you can restore the default settings of the HG622 by pressing and holding the RESET button for over six seconds.
Step 5 Enter the new access password in the WPA pre-shared key text box. Step 6 Select AES from the WPA encryption drop-down combo box. Step 7 Click Submit to save the settings. 5.4 Changing the Login IP Address To make the login IP address easy to remember, you can change the IP address after logging in to the Web-based configuration utility. To change the IP address, do as follows: Step 1 Choose Basic > LAN in the navigation tree. Step 2 Select the DHCP page.
After files are downloaded, you can view file downloading records on the Download History tab. 5.6 Restoring Default Settings You can quickly restore the default settings of the HG622 by pressing the RESET button on the rear panel. To restore the default settings, press and hold the RESET button for over six seconds after the HG622 is powered on, and then release the button. In addition, you can restore the default settings of the HG622 through the Web-based configuration utility.
3. Ensure that the terminal is properly connected to the socket through the power adapter. If the POWER indicator is still off, contact an authorized maintenance center. Step 2 After powering on the terminal, wait for about three minutes. Then, check whether the DSL indicator on the terminal is solid on. If the DSL indicator blinks for a long time, perform further checks as follows: 1. Ensure that telephone lines are properly connected.
operator. Step 6 Check whether you can use the PPP dial-up software to dial successfully. If you cannot use the PPP dial-up software to dial successfully, perform further checks as follows: 1. Stop the PPP dial-up software and then power off the terminal. After five minutes, power on the terminal, and then use the PPP dial-up software to dial again. 2. Restore the default settings of the terminal. If the problem persists, contact your network operator.
If the problem persists, contact your service provider. What can I do if sometimes the terminal cannot access the Internet through a WLAN connection or if the WLAN connection is unsteady? Step 1 Check the positions of your terminal and your computer. Ensure that they are far from the electric appliances, such as microwave ovens, refrigerators, or cordless telephones, that generate strong magnetic or electric fields. Step 2 Place your terminal in an open area.
7 Appendix 7.1 Indicators POWER DSL INTERNET WLAN 1 2 WPS 3 4 5 LAN1 LAN2 6 7 LAN3 LAN4 USB 8 9 10 No. Indicator Status Description 1 POWER On The HG622 is powered on. Off The HG622 is powered off. 2 DSL On The HG622 is activated. Blinking The HG622 is being activated. Off The HG622 is powered off.
No. Indicator Status Description 3 INTERNET On z z z Blinking z z z Off z z 4 WLAN On z z Blinking z z 5 6–9 10 WPS LAN1–LAN4 USB The HG622 works in routing mode. The WAN connection is set up. No data is being transmitted. The HG622 works in routing mode. The WAN connection is set up. Data is being transmitted. The HG622 works in bridge mode or in routing mode. No WAN connection is set up. The wireless network function is enabled. No data is being transmitted through the WLAN.
7.2 Interfaces and Buttons WLAN WPS 11 ON/OFF DSL 1 LAN4 LAN3 LAN2 LAN1 2 3 4 5 RESET 10 9 8 POWER 6 7 No. Interface or Button Description 1 DSL Used to connect HG622 to the MODEM interface on the splitter or to the telephone jack on the wall. 2-5 LAN1–LAN4 Used to connect Ethernet devices, such as PCs and switches. 6 RESET Used to restore the factory settings. Power on the HG622, press and hold the RESET button for at least 6 seconds, and then release the button.
No. Interface or Button Description 9 WLAN Used to enable or disable wireless network function quickly. 10 WPS Used to set up a wireless connection between the HG622 and a wireless terminal easily and safely. 11 USB Used to connect a USB device, such as a Huawei HSPA data card. 7.3 Default Settings Parameter Setting IP address of the LAN interface 192.168.1.1 Subnet mask of the LAN interface 255.255.255.
Item Specification Weight About 350 g Standards VDSL2 standards G.993.2 Annex B PSD Mask ITU G.994.1 (G.hs) ADSL2+ standard ITU G.992.5 (G.dmt.bitplus) Annex A ADSL2 standards ITU G.992.3 (G.dmt.bis) Annex A ITU G.992.3 (G.dmt.bis) Annex L ADSL standards ITU G.992.1 (G.dmt) Annex A ITU G.994.1 (G.lite) ANSI T1.413 Issue 2 WLAN standard 802.11b, 802.11g and 802.11n(2.4 GHz) 802.11b 1 Mbit/s, 2 Mbit/s, 5.5 Mbit/s, 11 Mbit/s 802.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China www.huawei.
