HUAWEI TE30 Videoconferencing Endpoint V100R001 User Guide Issue 01 Date 2013-03-27 HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2013. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
HUAWEI TE30 Videoconferencing Endpoint User Guide About This Document About This Document Overview This document describes how to install, configure, maintain, and troubleshoot the HUAWEI TE30 Videoconferencing Endpoint (TE30 or endpoint for short). It also includes step-by-step instructions for conferencing tasks.
HUAWEI TE30 Videoconferencing Endpoint User Guide Symbol About This Document Description Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury. Indicates a hazard with a medium or low level of risk, which if not avoided, could result in minor or moderate injury. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
HUAWEI TE30 Videoconferencing Endpoint User Guide Contents Contents About This Document .................................................................................................................... ii 1 Product Introduction .................................................................................................................... 1 2 Installation and Initial Configuration ...................................................................................... 3 2.1 Installing Your TE30 .....
HUAWEI TE30 Videoconferencing Endpoint User Guide Contents 6 Conference .................................................................................................................................... 39 6.1 Answering an Incoming Call and Exiting a Conference ................................................................................ 40 6.2 Setting Conference Parameters ...................................................................................................................... 40 6.
HUAWEI TE30 Videoconferencing Endpoint User Guide Contents 11.3 Logging In to the Endpoint Web Interface ................................................................................................... 83 11.4 Getting to Know the Web Interface Functions ............................................................................................. 84 11.4.1 Importing and Exporting the Address Book ........................................................................................ 85 11.4.
HUAWEI TE30 Videoconferencing Endpoint User Guide Contents B Technical Specifications ......................................................................................................... 123 C Videoconferencing Room Layout ......................................................................................... 127 D Default Settings ....................................................................................................................... 128 E Terminology ...............................
HUAWEI TE30 Videoconferencing Endpoint User Guide 1 Product Introduction 1 Product Introduction The TE30 is a compact, easy to install, and easy to use videoconferencing endpoint designed by Huawei. The TE30 is an all-in-one endpoint incorporating a digital camera and stereo microphone. It is ready for video communication as soon as it is powered on and connected to a network.
HUAWEI TE30 Videoconferencing Endpoint User Guide 1 Product Introduction Network Features Maximum call bandwidth: 4 Mbit/s IP-based network Packet loss concealment Wi-Fi capable Issue 01 (2013-03-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI TE30 Videoconferencing Endpoint User Guide 2 2 Installation and Initial Configuration Installation and Initial Configuration About This Chapter Install and configure your TE30 before use. 2.1 Installing Your TE30 Your TE30 offers multiple installation options. You can use any of them for quick deployment. 2.2 Connecting Cables Connect cables to your TE30 before using it for conferencing. 2.3 Powering On and Off With all cables connected to the TE30, power it on. 2.
HUAWEI TE30 Videoconferencing Endpoint User Guide 2 Installation and Initial Configuration Figure 2-1 Connecting cables In Figure 2-1: Video input: Use the built-in camera in your TE30 as the video input source. Your TE30 cannot be connected to external cameras. Presentation input: Use a VGA cable to connect the TE30 VGA IN port to a computer VGA out port. Audio input: Use the built-in microphone.
HUAWEI TE30 Videoconferencing Endpoint User Guide 2 Installation and Initial Configuration When your TE30 is powered on, ensure that the power cable is connected to the TE30 securely to prevent power disconnection. Before isolating your TE30 from its external power supply (for example, the power supply from a power socket) and removing the power cable, power off the TE30 properly. Check whether the power cable and power adapter are correctly connected to the relevant devices.
HUAWEI TE30 Videoconferencing Endpoint User Guide When the TE30 Is... 2 Installation and Initial Configuration OLED Display Shows...
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter 2 Installation and Initial Configuration Description Setting controlled UI. Time zone Specifies the time difference between the local time and the Greenwich Mean Time (GMT). Your TE30 automatically sets this parameter based on your settings of Location. The default value is (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi. Your TE30 automatically sets this parameter based on the value set for Location.
HUAWEI TE30 Videoconferencing Endpoint User Guide 2 Installation and Initial Configuration Parameter Description Setting Adjust time automatically based on DST Specifies whether to adjust the endpoint clock based on local observance of Daylight Savings Time (DST). This parameter is deselected by default. If this function is enabled, the endpoint clock is automatically adjusted one hour forward. NOTE The presence of this parameter is controlled by your settings of Time zone.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter 2 Installation and Initial Configuration Description Setting If you set the parameter to Opaque, no background photograph is displayed on the menu screen. If you st this parameter to values other than Opaque, a background photograph is displayed behind the menu screen with a degree of transparency corresponding to the value chosen. Display IP address Specifies whether to display the local IP address on the conferencing screen.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network 3 Network About This Chapter With network settings configured correctly, your TE30 can properly communicate with other network devices. 3.1 Setting IP Parameters To use your TE30 on an IP network to implement video communication, correctly set IP parameters, which include DNS server address, network interface mode, and gateway address. 3.2 Setting H.323 Parameters When an H.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network 3.1 Setting IP Parameters To use your TE30 on an IP network to implement video communication, correctly set IP parameters, which include DNS server address, network interface mode, and gateway address. Procedure Step 1 Choose Advanced Settings > Settings > Network > IP > IP. Set the IP parameters by referring to Table 3-1. Table 3-1 IP parameters Parameter Description Setting IPv6 Specifies whether IPv6 is used.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 3 Network Setting transmission rate is 100 Mbit/s, and data can be sent and received at the same time. PPPoE Specifies whether your TE30 accesses broadband networks using dial-up connections. The default value is Disable. NOTE If you set this parameter to Enable, you must also set Dialing mode, User name, and Password. Dialing mode Connection type Local IP address Specifies the dial-up connection mode.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network Parameter Description Setting Gateway address Specifies the gateway address that corresponds to the IP address of your TE30. Contact the network administrator. This parameter is mandatory when Connection type is set to Static IP. Subnet prefix length Specifies the prefix length for the IPv6 address of your TE30. Examples: IPv4 address: 192.168.1.1 IPv6 address: 2000:0:0:0:200:55:0:1 The default value is 0. Step 2 Select Save.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 3 Network Setting book by their IP addresses, numbers, and names. GK registration mode GK address If you do not select this parameter, the TE30 will not register with the GK. In this case, the TE30 can call other endpoints by their IP addresses only. Specifies the mode for registering your TE30 with a GK. Auto: Your TE30 automatically registers with an available GK on the network and obtains the GK address.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network Parameter Description Setting HTTPS mode Specifies whether to upload information about conferences initiated from your TE30 in HTTPS encryption mode. This parameter is selected by default. Multipoint conference authenticatio n This parameter is available when Huawei GK is selected. If you do not select this parameter, the TE30 will use the Transfer Control Protocol (TCP) to upload conference information, which may be insecure.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network Table 3-3 SIP parameters Parameter Description Setting Register with server Specifies whether to register your TE30 with a SIP server. This parameter is deselected by default. If you select this parameter and the TE30 successfully registers with the SIP server, the TE30 can call endpoints defined in the address book by their IP addresses, numbers, and names.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter User name Password 3 Network Description Setting endpoints that also register with the SIP server can dial this site number to call your TE30. Example: 12345 Specifies the name by which the SIP server identifies your TE30 after it registers with the SIP server. The value can consist of numbers, letters, Chinese characters, and special symbols such as @ # %.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network Step 2 Select Save. ----End 3.4 Setting Wi-Fi Parameters To use your TE30 to implement video communication over a Wi-Fi network, configure the Wi-Fi settings. Setting Wi-Fi Client Parameters After the Wi-Fi client is enabled, your TE30 functions as a Wi-Fi client and access a Wi-Fi network after connecting to a wireless router. Step 1 Choose Advanced Settings > Settings > Network > Wi-Fi > Wi-Fi Client and enable the Wi-Fi client.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network Table 3-4 Advanced wireless network parameters Parameter Description Setting SSID Number Specifies the name for your endpoint's Wi-Fi network. This parameter is mandatory. Channel Specifies the channel to transmit data through Wi-Fi signals. The default value is AUTO. The value is a string of 31 characters or less, consisting of digits, letters, Chinese characters, and special symbols, such as @ # %. Retain the default value.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 3 Network Setting If you set Encryption mode to NONE, the Wi-Fi network provided by your TE30 is open to everyone. Local IP address Specifies the IP address and subnet mask of your TE30. Examples: Local IP address: 192.168.1.10 Subnet mask: 255.255.255.0 Subnet mask DHCP Specifies whether your endpoint assigns IP addresses to devices connected to it. This parameter is deselected by default.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description IP priority Service type DSCP audio DSCP video DSCP data DSCP signaling Network jitter Lip sync. 3 Network Setting DiffServ: If you select this option, you must also set DSCP. DSCP stands for Differentiated Services Code Point. Specifies the priority that a network device gives to forwarding the data packets sent by your TE30. A larger value indicates a higher priority.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network 3.6 Setting Firewall Parameters With the firewall settings correctly configured, video conferences held using your TE30 are secure. Background The firewall protects your IP network by separating the internal and external network communication data.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 3 Network Setting site. Local listen port Specifies the local SIP listening port. The default value is 5060. Server listen port Specifies the listening port in the SIP server with which your TE30 registers. The default value is 5060. SIP call port Specifies the port used by your TE30 to send SIP signaling during communication with remote sites. The default value is 5060.
HUAWEI TE30 Videoconferencing Endpoint User Guide 3 Network 3.7 Setting Network Diagnostics Parameters Correct settings on the ports used for diagnostics enable you to use a network diagnostics tool to diagnose your TE30 using the ports. Procedure Step 1 Choose Advanced Settings > Settings > Network > Diagnostics. Set the network diagnostics parameters by referring to Table 3-7.
HUAWEI TE30 Videoconferencing Endpoint User Guide 4 Display and Camera 4 Display and Camera About This Chapter Before using the TE30, you need to connect video devices to it and set video parameters. Video devices include video input devices, such as a camera, DVD player, and computer, and video output devices, such as displays. To enable your TE30 to deliver HD video quality, ensure the video input and output devices support 720p or higher resolutions. 4.
HUAWEI TE30 Videoconferencing Endpoint User Guide 4 Display and Camera Table 4-1 Available video resolutions in each output mode Output Mode Video Resolution VGA OUT VGA 800 x 600 pixels, 1024 x 768 pixels, 1280 x 1024 pixels, 720p, 1080p YPrPb 720p and 1080p MAIN OUT HD DVI 1024 x 768 pixels, 1280 x 1024 pixels, 720p, and 1080p HDMI 720p and 1080p Video is smoother at a higher refresh rate. Select the refresh rate that is the same as the refresh rate of the display connected to your TE30.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 4 Display and Camera Setting video on one display and the remote controlled UI on another display by setting this parameter to a value different from the value of MAIN OUT HD. Specifies the video output port for captions. Caption output The default value is MAIN OUT HD. NOTE Settings for this parameter take effect only when the caption type is set to T.140. Main output interface Specifies the main output port.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 4 Display and Camera Setting TE30. HDMI: Select this option if you use an integrated cable to connect the HDMI port in the display to the HD-AI/TV/LAN/POWER port on your TE30. DVI: Select this option if you use an integrated cable to connect the DVI port in the display to the HD-AI/TV/LAN/POWER port on your TE30. Video resolution Specifies the resolution for each video output port.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter 4 Display and Camera Description Setting presentation and video. Small window position 2 panes: The presentation and video are displayed in two panes. 3 panes (a) or 3 panes (b): The presentation and video are displayed in three panes. Specifies the position of the PiP window on the screen. The default value is Lower right corner. This parameter is available only when Automatic layout mode is set to PiP.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 4 Display and Camera Setting preset after startup. NOTE Each camera preset stores the pan, tilt, and zoom settings of the camera. For details about how to set presets, see 4.4 Saving and Using Camera Presets. Moving speed Stretch mode Specifies the movement and zoom speed for the camera at your site. Select Slow for accurate positioning. Select Fast for quick positioning. Select Medium for medium paced positioning.
HUAWEI TE30 Videoconferencing Endpoint User Guide 4 Display and Camera 4.3.1 Selecting a Camera To control a camera, first select the camera. Background When the TE30 is not in a conference, you can only select and control the local camera. When the TE30 is in a conference, you can select and control the local and remote cameras. Procedure Step 1 Press on the remote control to switch to the local or remote camera.
HUAWEI TE30 Videoconferencing Endpoint User Guide 4 Display and Camera 4.4 Saving and Using Camera Presets Camera presets are camera positions you stored ahead of time. Each camera preset stores the pan, tilt, and zoom (PTZ) settings of the camera. You can simply control the camera by switching the camera between the camera presets. The camera supports PTZ functions, you can creat and save a maximum of 30 camera presets for the camera. A camera preset remains valid until it is deleted or changed.
HUAWEI TE30 Videoconferencing Endpoint User Guide 5 5 Microphone and Speaker Microphone and Speaker About This Chapter While your TE30 provides a built-in microphone, you can connect external microphone arrays or other audio devices to the TE30 as audio input sources. Before using the TE30, connect the audio input devices to the TE30 and set audio input parameters correctly. 5.2 Connecting a Speaker You can connect your TE30 to external speakers for louder audio output and better audio quality. 5.
HUAWEI TE30 Videoconferencing Endpoint User Guide 5 Microphone and Speaker 5.1.1 Connecting a VPM220 The VP220 provides 180°sound pickup and an optimal pickup range of six meters. Use the 10 m proprietary cable provided with the VPM220 to connect the HD-AI connector of the TE30 integrated cable to the IN port on a VPM220. Once the connection is set up, your TE30 automatically uses the VPM220 instead of its built-in microphone for sound pickup.
HUAWEI TE30 Videoconferencing Endpoint User Guide 5 Microphone and Speaker Step 2 Touch and hold the button in the center of the VPM220 top surface for 5 seconds. A confirmation dialog box is displayed. Step 3 Select Confirm. The VPM220W sets up a WPS connection with the TE30 and attempts to obtain an IP address. After the VPM220W obtains an IP address, its indicator is steady blue. ----End The status indicators can quickly provide information about the VPM220W working status.
HUAWEI TE30 Videoconferencing Endpoint User Guide 5 Microphone and Speaker For details, see the HUAWEI VPM220W Microphone Array User Guide and HUAWEI VPM220W Microphone Array Quick Start Guide. 5.1.3 Connecting Other Audio Input Devices You can connect other audio input devices, such as a computer or mobile phone to the LINE IN port on your TE30. 5.2 Connecting a Speaker You can connect your TE30 to external speakers for louder audio output and better audio quality.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 5 Microphone and Speaker Setting mode. MIC 1 and LINE IN 1 ports are used for the left audio channel input source, and MIC 2 and LINE IN 2 are used for the right audio channel input source. Adjusts the volumes for the MIC 1, MIC 2, LINE IN 1, and LINE IN 2 ports. Value range: -12 dB to +12 dB Volume indicator Displays the volumes in real time. No default value is set for this parameter.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 5 Microphone and Speaker Setting Settings > Audio > Audio Input and select the audio input ports you want to enable. Turn to Mute Specifies whether to mute the microphone at your site when the camera rotates to prevent noises caused by the rotation. The default value is Enable. Table 5-6 Volume and audio effect parameters Parameter Description Setting Speaker volume Adjusts the speaker volume.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference 6 Conference About This Chapter You can create a conference or answer a call to join a conference. 6.1 Answering an Incoming Call and Exiting a Conference You can specify how your TE30 handles incoming calls. You can also exit a conference anytime. 6.2 Setting Conference Parameters Your TE30 is ready for videoconferencing with its default conference settings, but you can customize the conference settings based on the site requirements. 6.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference 6.1 Answering an Incoming Call and Exiting a Conference You can specify how your TE30 handles incoming calls. You can also exit a conference anytime. Answering an Incoming Call Depending on your configuration, your TE30 answers the call automatically or prompts you to answer the call manually. If you set Answer Mode to Answer call automatically and the TE30 is not in a conference, the TE30 answers the call automatically.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Table 6-1 General conference parameters Parameter Description Setting Answer Mode Specifies how your TE30 handles incoming calls. The default value is Manual. Open do not disturb right Manual: Your TE30 prompts you to handle a call when the call comes in. Answer call automatically: Your TE30 automatically answers incoming calls when not being used in a conference.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 6 Conference Setting when Wi-Fi is enabled. For details, see 3.4 Setting Wi-Fi Parameters. Call times Default call bandwidth Specifies the maximum number of attempts your TE30 calls a specified site after startup. The default value is 1. Specifies the default data transmission rate for your TE30. The default value is 1920kbps. The maximum value is 10.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 6 Conference Setting at your site. Video resolution If you select Auto, Video resolution is available. If you do not select Auto, you must also set Video resolution and Video frame rate. Specifies the video format. The available options vary depending on your settings of Video protocol. The default value is Auto.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description If you select Auto, you must also set Presentation resolution. If you select Auto, you must also set H.239 video resolution. 6 Conference Setting H.239 video resolution Specifies the presentation format. The available options vary depending on your settings of H.239 video protocol. The default value is Auto. Presentation resolution Specifies the presentation video resolution. The default value is Sharp. H.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 6 Conference Setting parameter to Limited for better video conference quality. Dynamic bandwidth reserved presentation bandwidth Specifies whether the TE30 implements the following if the packet loss rate increases due to insufficient network bandwidth: automatically decreases the conference bandwidth until packet loss does not occur constantly or the conference bandwidth is decreased to 64 kbit/s.
HUAWEI TE30 Videoconferencing Endpoint User Guide In the text box, enter the name or IP address of the site you wish to call. Then press or 6 Conference on the remote control. From the address book, select the site or group you wish to call. Then press on the remote control. or You can configure a Lightweight Directory Access Protocol (LDAP) address book on your TE30. For details, see 6.8.2 Managing the Network Address Book. Select or press and hold the site you wish to call.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference From the Conference History Screen The conference history contains the records of conferences your TE30 initiated or attended and sites your TE30 placed calls to or received calls from. You can select a record from the conference history and initiate the conference. From the Conference History screen, select a conference and press remote control to initiate the conference.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference 6.5 Creating a Favorite Conference If you need to regularly join certain conferences, you can save those conferences as favorite conferences. You can then quickly join a favorite conference without having to reset the conference parameters again. Procedure Step 1 Choose Advanced Settings > Conference Schedules > Conference. Step 2 Select Create. Step 3 Select Add Site. You can add sites using Address Book, Others, or LDAP Address Book.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Parameter Description Setting Conference control password Specifies the password to the conference. This password can be used in the following two ways: The endpoint alias can contain up to 32 digits. H.235 conference SRTP conference Paying site The site that wants to chair the conference to obtain the chair control rights. Anonymous sites to join the conference if the conference is an authentication one.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference To modify a favorite conference, select it and press To delete a favorite conference from the favorite conference list, select it and press next to the conference. next to the conference. 6.6 Scheduling a Conference On your TE30, you can schedule a conference to hold the conference at specific time. Prerequisites Ensure that: The TE30 is registered with a GK, and the Huawei GK is enabled. For details, see 3.2 Setting H.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Figure 6-1 Procedure for joining an authentication conference Setting the number of anonymous sites: Set the number of anonymous sites when initiating a conference. For details, see Table 6-3. Setting the authentication conference password: When initiating the conference, set Conference control password, which serves as the authentication password. Anonymous sites must enter this password to join the conference.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference If the authentication conference is password-protected, the system plays an interactive voice response (IVR), prompting you to enter the password. If the conference is not password-protected, you can join the conference after selecting the desired language. ----End 6.8 Managing the Address Book The address book stores site information. You can add, edit, and delete site entries.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter 6 Conference Description Specifies the line used for the site to access the videoconferencing network. Type If you select IP, your TE30 will use the protocol set for Preferred IP protocol to call the site. If you set Category to CT site, the available value for this parameter is SIP. Specifies the site number used to place calls between sites. Number IP address The IP, E1, T1, 4E1, basic rate interface (BRI), and H.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Parameter Description Setting Area code Specifies the area code for the site. Set this parameter based on your Country/Region code settings. No default value is set for this parameter. This parameter is required when Type is set to ISDN or PSTN. Line 2 #2 Specify the numbers used by your TE30 to call the site. These parameters are available only for ISDN sites. You can set two numbers for each BRI line.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Modifying, Deleting, and Searching You can modify, delete, and search for in the address book. Modifying a Record Select a site or group, press on the remote control, and modify the site or group settings. Deleting a Record Select next to the desired site or group to delete it from the address book.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Parameter Description Setting FTPS Specifies whether to use FTPS to encrypt data through the SSL and ensure data integrity. This parameter is selected by default. If FTPS is not used, the TE30 uses FTP, which is insecure. To improve communication security, select this parameter.
HUAWEI TE30 Videoconferencing Endpoint User Guide 6 Conference Managing the LDAP Network Address Book With the LDAP directory server parameters set correctly, the TE30 can access the LDAP server and search sites in the LDAP network address book. Configuring the LDAP Directory Server Step 1 Choose Advanced Settings > Settings > Network > Network Address Book > LDAP Server. Set the LDAP directory server parameters by referring to Table 6-6.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter 6 Conference Description Setting set Automatic update interval and Local records prevail if duplicates exist. Local records prevail if duplicates exist Specifies whether the following function is enabled: If some records in the address book on the LDAP server already exist in the local address book, these records remain unchanged when the local address book is updated. This parameter is deselected by default.
HUAWEI TE30 Videoconferencing Endpoint User Guide 7 Conference Control 7 Conference Control About This Chapter During a multipoint conference, you can control the video and audio of participant sites using conference control functions. A conference can be chaired by only one site. Another site can chair the conference only after the current chair site releases its chair control rights.
HUAWEI TE30 Videoconferencing Endpoint User Guide 7 Conference Control Step 2 Select Save. ----End 7.2 Performing Conference Control On the TE30, you can manage the audio and video of participant sites by performing conference control operations. Non-chair sites have access to only four conference controls: Request chair, Request floor, View site, and Revoke chair. The chair site has access to all conference controls.
HUAWEI TE30 Videoconferencing Endpoint User Guide 7 Conference Control After the chair site gives the floor to a site, the video and sound of the site are broadcast, and all the sites, except the chair site and the site given the floor, are muted. To give the floor to a site, access the Give Floor screen, scroll to the site, and press on the remote control. To take back the floor, select Discussion.
HUAWEI TE30 Videoconferencing Endpoint User Guide 7 Conference Control Mute/Unmute MIC After you have muted the microphone of a site, the other sites in the conference cannot hear the site. To enable the site to be heard, unmute the microphone of the site. Depending on the microphone status of a remote site, you can mute or unmute the remote microphone after selecting the site: : indicates that the microphone of the site is not muted. You can press the microphone.
HUAWEI TE30 Videoconferencing Endpoint User Guide 7 Conference Control This function is available only when the continuous presence resources have been reserved for the conference. To set continuous presence: Select a pane. From the drop-down list box in the displayed dialog box, select the site whose video you wish to display in the pane. Then select OK. If a site already exists in the pane selected, the site will be displaced by the site you newly select.
HUAWEI TE30 Videoconferencing Endpoint User Guide 7 Conference Control Audio: All sites have unmuted microphones, and the sound of all the sites are mixed and broadcast to every site. Video: The video viewed by each site does not change and each site can view any other site. Add Site During a conference, the chair site can add sites to the current conference as required. If a site is successfully added to the conference, the site becomes a participant in the conference.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio 8 Video and Audio About This Chapter During a conference, you can control the video and audio of the sites participating in the conference. 8.2 Adjusting Audio Effects You can adjust the audio effects by modifying the settings for the audio input, sound effect, and volume. 8.3 Adjusting the Local Volume You can adjust the local speaker volume by pressing or on the remote control. 8.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio Background Picture offset may occur in video input or output, such as the computer desktop when it is displayed on the display screen. You can adjust the picture offset in this case. Procedure Step 1 Choose Advanced Settings > Settings > Video > Image Offset. Step 2 Select VGA IN or VGA OUT. Step 3 Select Horizontal offset or Vertical offset and move the slider. ----End 8.1.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter 8 Video and Audio Description Vivid: delivers brighter video with cooler color. Natural: delivers video with warmer colors. User defined: delivers video with custom settings. After you select this option, you can set the following parameters: − Aperture: Sharpens video edges and contours to preserve the impression of clarity and fine details. Over-sharpening will make video less realistic.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio Parameter Description Setting Image inversion Specifies whether the video input from the camera is rotated by 180 degrees. The default value is Disable. If the video is displayed in an reverse direction, you can enable this function. VGA IN Brightness Specifies the video output level that changes the brightness of the video displayed on a display. Value range: 0-100 The default value is 50.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio If the packet loss rate is greater than or equal to threshold B, is displayed. Other Icons Status icons are displayed on screens if the following condition is met: You have set the icon to be displayed on screens as follows: Choose Advanced Settings > Settings > Display > Icon and select the icons to be displayed on screens. The function that corresponds to the status icon has been enabled or is available. 8.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio 8.3 Adjusting the Local Volume You can adjust the local speaker volume by pressing or on the remote control. Press to increase the volume or to decrease the volume. Changing the volume affects only the sound you hear at your site. 8.4 Adjusting the Screen Layout By adjusting the screen layout, you can view multiple videos on the same display. Only the main output port supports combined picture output. For details, see Table 4-4.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio The icon for the local or remote presentation disappears once the local presentation source is disconnected from the TE30 or the sharing of the remote presentation stops. Before a conference starts, you can set the position of the PiP window on the screen. For details, see Table 4-4. 8.5 Selecting Video Sources You can specify video input ports for the local video, local presentation, and remote video.
HUAWEI TE30 Videoconferencing Endpoint User Guide 8 Video and Audio Step 2 Select Save. After the function to hide the local video is enabled, depending on your configuration, may be displayed in the lower right corner of the video in full screen. For details about how to set the presence of the preceding icon, see 8.1.4 Customizing the Onscreen Status Icons. ----End Issue 01 (2013-03-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI TE30 Videoconferencing Endpoint User Guide 9 Captions 9 Captions About This Chapter You can create a caption on your TE30 and, during a conference, share the caption with remote sites. Your TE30 supports T.140 and non-T.140 captions. Table 9-1 describes the differences between these caption types. Table 9-1 Differences between T.140 and non-T.140 captions Non-T.140 Caption T.
HUAWEI TE30 Videoconferencing Endpoint User Guide 9 Captions 9.3 Sharing a Caption After you create a caption, you can share the caption with remote sites. 9.4 Sending an Instant Message During a conference, you can send instant messages to remote sites. 9.1 Specifying Caption Settings Caption settings include the caption font size, color and background. Procedure Step 1 Choose Advanced Settings > Settings > Display > Caption. Set the caption parameters by referring to Table 9-2.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description cy 9 Captions Setting transparent. Scrolling speed Specifies the percentage of the banner or bottom caption height to the entire display. The default value is 10%. Font Type Specifies the font type of the caption. The default value is Boldface. Bold Specifies whether the banner or caption is displayed in bold. For banners, this parameter is selected by default.
HUAWEI TE30 Videoconferencing Endpoint User Guide 9 Captions Prerequisites The TE30 is in a conference, and a caption has been created. Procedure Step 1 Choose Advanced Settings > Utilities. The Utilities screen is displayed. Step 2 Select Middle Caption, Banner, or Bottom Caption. Step 3 Select a caption or banner and select Send. ----End 9.4 Sending an Instant Message During a conference, you can send instant messages to remote sites. Prerequisites The TE30 is in a conference.
HUAWEI TE30 Videoconferencing Endpoint User Guide 10 Security 10 Security About This Chapter Your TE30 provides security features and configuration. 10.1 Security Features Your TE30 provides a variety of security features, including protocol anti-attack measures and authentication for debug users, web interface users, and web requests. 10.
HUAWEI TE30 Videoconferencing Endpoint User Guide 10 Security Web Request Authentication When a user requests to access a specified web page or submits a servlet request, the TE30 checks that the user's session identifier is valid and that the user is authorized to perform the operation. The server implements the final authentication. The server verifies the user-generated data.
HUAWEI TE30 Videoconferencing Endpoint User Guide 10 Security Table 10-1 Administrator password parameters Parameter Description Setting Current password The administrator password contains a maximum of 32 alphanumeric characters. By default, no password is set. New password Confirm password Step 2 Select Save. ----End 10.2.2 Enabling Encryption You can enable encryption to improve video communication security.
HUAWEI TE30 Videoconferencing Endpoint User Guide 10 Security Table 10-2 Web-based login parameters Parameter Description Setting Web Login Specifies whether to allow logins using the endpoint web interface. If you select this parameter, you must also set the administrator user name and password. This parameter is selected by default. Administrator name Specify the user name and password used to log to the endpoint web interface.
HUAWEI TE30 Videoconferencing Endpoint User Guide Parameter Description 10 Security Setting first login. SSH Specifies whether to enable SSH, which improves transmission security and prevents information disclosure. This parameter is selected by default. Step 2 Select Save. ----End 10.2.4 Setting the Upgrade Password You can set the password required to upgrade the TE30 software using the upgrade tool and web interface. Step 1 Choose Advanced Settings > Settings > Secured > Upgrade password.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 11 Web-based Remote Management Web-based Remote Management About This Chapter Your TE30 supports remote management using the web interface. From the web interface, you can set parameters, view the settings, and control the TE30. The major features of operating the TE30 using the web interface are as follows: A computer is used to access the IP network where the TE30 is located.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management The web-based login can be enabled or disabled on the remote controlled UI. For details, see 10.2.3 Allowing Remote Login. 11.2 Configuring the Web Browser Before using the web interface for TE30 remote management, configure the web browser on your computer. Background The following procedure uses Internet Explorer 8.0 as an example of how to configure a browser.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management Procedure Step 1 Open Internet Explorer. Step 2 In the address box, enter your TE30 IP address, such as 10.10.10.10. Step 3 Press Enter. The login page is displayed. Step 4 Fill in User name and Password. The default user name and password are admin. Step 5 From the Language drop-down list, select a language. Step 6 Select Log In. The home page is displayed, as shown in Figure 11-1.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management The following are the functions unique to the web interface: Importing and exporting the address book Importing and exporting settings Importing a license file Customizing the shortcut bar and desktop icons Site map Conference control page, site list, and site template Conference controls Importing a certificate Recording Backing up settings Capturing photos 11.4.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management Step 2 Select Import to Local Address Book and select file B to import. Step 3 Select Import. ----End 11.4.2 Importing and Exporting Settings From the endpoint web interface, you can import or export settings. After your endpoint is restored to its default settings, you can import previously exported settings. Procedure Step 1 Log in to the endpoint web interface. Choose System Settings > Installation.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management Step 4 Click Back when OK is displayed. The new license file takes effect after the TE30 is restarted. ----End 11.4.4 Customizing Shortcut and Desktop Icons You can customize the shortcut icons and desktop icons on the web interface so that you can perform desired operations more conveniently. Background The following procedure takes the customization of shortcut icons as an example.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management If the TE30 is connected to an IMS network and the conference is managed by the portal provided by the IMS, this section does not apply. Template Used to View Sites In Turn You can preset and save a viewing order of sites in a template. Afterward, you can conveniently view the sites in the order saved in the template without additional configuration.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management 11.4.8 Importing a Certificate You can import client, server, and SiteCall certificates into the TE30. These certificates can be used to identify users, certificate authorities, and servers to improve communication security. Prerequisites You have downloaded the required certificate from a SIP server or certificate authority. Procedure Step 1 Log in to the endpoint web interface. Choose System Settings > Installation.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management When you are scheduling or initiating a conference on an MCU, select Support recording under conference settings. Procedure Step 1 Log in to the endpoint web interface. Choose Conference > Control Recording. Step 2 Click Start. The recording starts. ----End Follow-up Procedure To stop recording, click Stop. 11.4.
HUAWEI TE30 Videoconferencing Endpoint User Guide 11 Web-based Remote Management Prerequisites The web login and video monitoring functions are enabled. For details, see 10.2.3 Allowing Remote Login. Procedure Step 1 Log in to the endpoint web interface. Choose Device Control > Video Control. When you are on the Video Control page, monitoring is enabled. appears on the endpoint display to indicate that video Step 2 Select the source you want to take a photo of and click Capture.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting 12 Troubleshooting About This Chapter This chapter describes the problems you might encounter when using your TE30 and provides corresponding solutions. To adopt certain solutions described in this chapter, access the Advanced Settings > Settings and Advanced Settings > Diagnostics screens. If the Advanced Settings screen is password protected, you must enter the password for access. For details, see 10.2.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting Problem Possible Cause Solution to download images. address of your endpoint has not been added to the list of trusted sites. Internet Options. 2. Click the Security tab, Trusted sites, and then Sites. 3. In Add this Web site to the zone, enter your TE30 IP address. Then click Add. 4. Click OK. Button text is not displayed completely. Internet Explorer is set to ignore font styles specified on web pages.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting Problem Possible Cause Solution message is displayed to indicate that the number of connections to the TE30 has reached the limit. connection attempts is less than 10 minutes, the TE30 counts these two attempts as separate connections. When connection attempts are frequent, the connections limit is easily reached.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting Problem Possible Cause Solution local video but not the remote video. value of Video bandwidth[frame rate] is 0, no video is sent from the remote site. administrator to solve this problem. If the remote video is displayed as a blue screen, the remote site hides its video by sending a blue screen. Contact the remote site administrator to solve this problem. The video output port is set to display the local video.
HUAWEI TE30 Videoconferencing Endpoint User Guide Problem 12 Troubleshooting Possible Cause Solution optical fiber transceiver is poor. While the TE30 is in a conference, the remote video can be displayed continuously but the video quality is not satisfactory. Ask the remote site administrator to perform a local video loopback test. If the video quality is good, the video frame rate set at the remote site is too high.
HUAWEI TE30 Videoconferencing Endpoint User Guide Problem 12 Troubleshooting Possible Cause Solution Remote control is disabled on the remote camera. Ask the remote site administrator to enable the remote camera control at the remote site. The camera settings are incorrect. Ask the remote site administrator to verify the camera settings. used to control the camera.
HUAWEI TE30 Videoconferencing Endpoint User Guide Problem 12 Troubleshooting Possible Cause Solution is powered off. In this case, power on the device. The audio cable is connected insecurely. In this case, reconnect the audio cable to the TE30. While the TE30 is in a conference, only the sound from the local site can be output from the display and you cannot hear the other sites. A loopback test is being performed at the local site. Stop all local and remote loopback tests. 12.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting Problem Possible Cause Solution using the IP address. The local endpoint is on a private network while the remote endpoint is on a public or different private network, and the NAT settings are incorrect. Check whether your TE30 can communicate with a public network. If it cannot, the NAT settings are incorrect. Choose Advanced Settings > Settings > Network > Firewall and verify the NAT settings.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting Problem Possible Cause Solution TE30. The local site is set to pay for the conference, but the account balance of the local site is insufficient. Enter the account number and the password correctly and top up the relevant account. Another site is to pay for the conference, but the corresponding account number or password is incorrect or the account balance of the site is insufficient.
HUAWEI TE30 Videoconferencing Endpoint User Guide 12 Troubleshooting 12.7 Viewing Help on the User Interface The endpoint user interface includes context-sensitive help and operation guide. Context-sensitive help includes status icons and configuration verification messages that are displayed in context on the user interface web pages. For example, if certain settings on the system settings screen are incorrect, a message will be displayed to indicate where the error exists and how to rectify the error.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance 13 Maintenance About This Chapter This chapter describes maintenance and troubleshooting methods to help you maintain and troubleshoot the TE30 during use. 13.3 Restoring Default Settings If software update fails and your TE30 malfunctions, use the Restore Default function to restore your TE30 to its default settings. 13.4 Configuring the NTP server.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance If any of the items does meet the requirement, power off the TE30 and take measures to improve the environment. Ensure that the TE30 is used only when all the listed items meet the requirements. Table 13-1 Checking the working environment Item Requirement Operating temperature 0 C to 40 C Operating humidity 10% to 80% RH 13.1.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance Choose Advanced Settings > Diagnostics > Status.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance To search for a log, select Query and specify the search criteria. Procedure Choose Advanced Settings > Diagnostics > Logs. Then select the log you want to view. 13.2 Software Upgrade Your TE30 supports the following software upgrade methods: automatic, locally, using the bootrom system, and from the web interface. During the upgrade, do not power off the TE30 to prevent faults that cannot be rectified.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance 13.2.1 Automatic Upgrade With the automatic upgrade enabled, your TE30 obtains upgrade files from the specified server and installs the upgrade files when the upgrade interval arrives. Procedure Step 1 Choose Advanced Settings > Settings > Installation > Auto Upgrade Settings. Step 2 Set the automatic upgrade parameters by referring to Table 13-3.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance The computer is connected to the TE30 using a straight-through cable, crossover cable, or switch. Upgrading One TE30 You can upgrade a single TE30 using the upgrade program installed on a computer. Procedure Step 1 Power on the computer and the TE30. Step 2 Extract the compressed software upgrade package on the computer. Step 3 Run UpgMaster.exe to display the window shown in Figure 13-1.
HUAWEI TE30 Videoconferencing Endpoint User Guide Step 5 Click 13 Maintenance to display the window as shown in Figure 13-2. Figure 13-2 Upgrading multiple TE30s at a time Step 6 In the area circled in red and marked as 1, enter the number of the TE30sto be upgraded, for example, 3. Step 7 In the area circled in red and marked as 3, enter the IP addresses of the TE30s to be upgraded. Step 8 In the area circled in red and marked as 4, enter the upgrade passwords of the TE30s to be upgraded.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance Step 3 Run UpgMaster.exe to display the window shown in Figure 13-2. Step 4 Click Browser and select the Telepresence.dat file. Step 5 Press Ctrl+ALT+P to display the window shown in Figure 13-3. Figure 13-3 Selecting the software modules to be upgraded Step 6 Select the software modules to be upgraded. Step 7 Click Pack File to pack the software modules to be upgraded into a .dat file, and save the file to the computer.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance 13.2.3 Upgrading the TE30 Using the Bootroom System If upgrading the endpoint using its normal system fails, you can use the bootrom system for the upgrade Prerequisites Before the upgrade, note the following prerequisites: A copy of the target software is available on the computer. The computer is connected to the TE30 using a crossover cable or a switch.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance Upgrading the TE30 Online Step 1 Log in to the endpoint web interface. Choose System Settings > Installation. The Installation page is displayed. Step 2 Click Auto Upgrade Settings. The Auto Upgrade Settings page is displayed. Step 3 Set the upgrade parameters by referring to Table 13-3. Step 4 Perform any of the following: If you did not enable automatic upgrade, click Manual upgrade to manually upgrade the TE30.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance To view the serial number of your TE30, choose Advanced Settings > Diagnostics > System Information > Version. Press and hold the MODE button for 10 seconds or more, and the TE30 will be restored to its default settings and restart. After the endpoint is restored to its default settings, its IP address is reset to 192.168.1.1. ----End 13.4 Configuring the NTP server.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance Parameter Description Setting Scheduled power-on Specifies whether the TE30 automatically powers on at the specified time. The default value is Disable. If you enable this function, you must also set Scheduled power-on time. Scheduled power-on time Specifies the time when the TE30 is automatically powered on. The default value is 0:0 corresponding to 24-hour. The value format depends on the value set for Time format.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance 13.6 Setting the Number Key Functions You can configure the number keys on the remote control for two-stage dialing or camera preset control. When your TE30 is not in a conference, and the display is in full screen mode, the number keys on the remote control do not support two-stage dialing and can only be used to control camera presets.
HUAWEI TE30 Videoconferencing Endpoint User Guide 13 Maintenance Audio signals are transmitted in the following signal path: Local microphone → 1 → 5 → Communication network → 6 → 7 → Remote speaker Local speaker ← 2 ← 5 ← Communication network ← 6 ← 8 ← Remote microphone Video signals are transmitted in the following signal path: Local camera → 3 → 5 → Communications network → 6 → 9 → Remote monitor Local monitor ← 4 ← 5 ← Communications network ← 6 ← 10 ← Remote camera Sound and Color Ba
HUAWEI TE30 Videoconferencing Endpoint User Guide Test 13 Maintenance Item to Be Tested Signal Stream modules video loopback tests simultaneously.
HUAWEI TE30 Videoconferencing Endpoint User Guide A Safety Precautions A Safety Precautions For safety purposes, carefully read through these safety precautions and observe them during operation. Basic Requirements Keep the device dry and secure from collision during storage, transportation, and operation of the device. Do not attempt to dismantle the device by yourself. In case of any fault, contact the appointed maintenance center for assistance or repair.
HUAWEI TE30 Videoconferencing Endpoint User Guide A Safety Precautions Before plugging or unplugging any cable, shut down the device and disconnect the power supply. While plugging or unplugging any cable, ensure that your hands are dry. Do not step on, pull, or overbend any cable. Otherwise, the cable may be damaged, leading to malfunction of the device. Do not use old or damaged cables.
HUAWEI TE30 Videoconferencing Endpoint User Guide A Safety Precautions LCD Usage Requirements Do not expose the LCD to direct sunlight. Do not press, scratch, or beat the LCD, or place heavy objects on top of it. Do not watch the LCD screen for a long time. This may harm your eyes or blur your vision. LCD Cleaning Requirements According to the instructions in the attached manual, use a piece of soft cloth to remove dust from the surface of the LCD.
HUAWEI TE30 Videoconferencing Endpoint User Guide A Safety Precautions Statement on a Class A Product This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. European Regulatory Compliance TE30 complies with the following European directives and regulations. 1999/5/EC (R&TTE) 2002/95/EC & 2011/65/EU (RoHS) EC NO.
HUAWEI TE30 Videoconferencing Endpoint User Guide A Safety Precautions FCC Part 15 TE30 complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device does not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. If this device is modified without authorization from Huawei, the device may no longer comply with FCC requirements for Class B digital devices.
HUAWEI TE30 Videoconferencing Endpoint User Guide A Safety Precautions This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
HUAWEI TE30 Videoconferencing Endpoint User Guide B Technical Specifications B Technical Specifications To better use your TE30, knowing technical specifications of the TE30 is important. Table B-1 lists the technical specifications of the TE30. Table B-1 Technical specifications Category Item Specifications Standards compliance Multimedia frame protocol ITU-T H.323 and IETF SIP Video standard H.264 SVC, H.264 HP, H.264 BP, H.263, and H.263+ Audio standard G.711, G.722, G.728, G.722.1*, G.722.
HUAWEI TE30 Videoconferencing Endpoint User Guide Category B Technical Specifications Item Specifications Video resolution 1080p30 with a minimum bandwidth of 512 kbit/s (Optional) 720p60 with a minimum bandwidth of 512 kbit/s (Optional) 720p30 with a minimum bandwidth of 384 kbit/s 4SIF/4CIF with a minimum bandwidth of 128 kbit/s SIF/CIF with a minimum bandwidth of 64 kbit/s SQSIF/SQCIF/QSIF/QC IF with a minimum bandwidth of 64 kbit/s Input: 1920 x 1200, 1080p (1920 x 1080)
HUAWEI TE30 Videoconferencing Endpoint User Guide Category B Technical Specifications Item Specifications OUT port Audio processing Acoustic echo cancellation (AEC), acoustic noise suppression (ANS), automatic gain control (AGC), VoiceClear, and AudioEnhancer HD-AI/TV/LAN/POWER port Functions as an HDMI, Ethernet, microphone, or power port using the integrated cable. USB port USB USB2.
HUAWEI TE30 Videoconferencing Endpoint User Guide Category B Technical Specifications Item Specifications Exposure mode Automatic and manual White balance Automatic and manual The dimensions may vary according to the actual product. The dimensions provided in the preceding table is for your reference only. Issue 01 (2013-03-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI TE30 Videoconferencing Endpoint User Guide C C Videoconferencing Room Layout Videoconferencing Room Layout When using the TE30, pay attention to your sitting posture to avoid problems associated with the spinal cord. Do not stare at the display screen for a long time. This may harm your eyes or blur your vision. Layout Precautions Ensure that there are no large or moving objects behind you. Otherwise, the video cannot be viewed clearly. Do not use striped patterns as the background.
HUAWEI TE30 Videoconferencing Endpoint User Guide D Default Settings D Default Settings To better use your TE30, get to know the default values of common user names and passwords. Table D-1 lists the default user name and passwords of the TE30. Table D-1 Default user names and passwords Item Default Setting Administrator password for the remote controlled UI By default, no password is set. Administrator user name and password for the web interface The default values are both admin.
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology E Terminology Numerics 1080i 1080i is the shorthand name for a format of high-definition video modes. 1080 denotes the number of horizontal scan lines - also known as vertical resolution - and the letter i stands for interlaced. In the alternate format of high-definition video mode, known as 1080p, the p would stand for progressive scan. 1080i is generally used in place of 1440x1080, at a frame rate of 29.
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology resolution (also known as 720 pixels of vertical resolution), while the letter p stands for progressive scan or non-interlaced. When broadcast at 60 frames per second, 720p features the highest temporal (motion) resolution possible under the ATSC standard. Progressive scanning reduces the need to prevent flicker by filtering out fine details, so sharpness is much closer to 1080i than the number of scan lines would suggest.
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology D delete site Remove a site from the site list. dual stream During a conference, two channels of video streams can be sent or received simultaneously. For example, one channel is used for transmitting video (such as video captured by a camera) and the other channel is used for transmitting presentation (such as a computer desktop). The two channels of videos can be displayed on two displays. end conference End a conference.
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology H.3xx-series terminals". Practical importance of this recommendation is its setting forth a way to have multiple video channels (for example, one for conferencing, another for presentation) within a single session (call). H.261 H.261 is a 1990 ITU-T video coding standard originally designed for transmission over ISDN lines on which data rates are multiples of 64 kbit/s. It is one member of the H.
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology HD Refers to a video system of higher resolution than standard-definition (SD) video, most commonly at display resolutions of 1280×720 (720p) or 1920×1080 (1080i or 1080p, full HD).
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology S S-Video Separate Video[1], more commonly known as S-Video, also called Y/C, and sometimes incorrectly [2] referred to as Super Video[3], is an analog video signal that carries video data as two separate signals: luma (luminance) and chroma (color).
HUAWEI TE30 Videoconferencing Endpoint User Guide E Terminology introduced in 1990. Today, it is the most common appellation of the 1024×768 pixels display resolution, but the official definition is broader than that. Issue 01 (2013-03-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI TE30 Videoconferencing Endpoint User Guide F F Acronyms and Abbreviations Acronyms and Abbreviations Numerics 3G Third Generation Mobile Telephony 4CIF 4 x Common Intermediate Format A AAC-LD Advanced Audio Coding-Low Delay ADSL Asymmetric Digital Subscriber Line AES Advanced Encryption Standard B BNC Bayonet Neill-Concelman connector BRI Basic Rate Interface C CAS Channel Associated Signaling CCD Charge Coupled Device CCS Common Channel Signaling CDMA Code Division Multiple
HUAWEI TE30 Videoconferencing Endpoint User Guide F Acronyms and Abbreviations DNS Domain Name Server DSCP Differentiated Services Code Point DVI Digital Visual Interface F FTP File Transfer Protocol G GK Gatekeeper GMT Greenwich Mean Time H HD High Definition HDMI High Definition Multimedia Interface I IMS IP multimedia subsystem L LDAP Lightweight Directory Access Protocol M MCU Multipoint Control Unit N NAT Network Address Translation NTSC National Television Standards Committe
HUAWEI TE30 Videoconferencing Endpoint User Guide F Acronyms and Abbreviations PSTN Public Switched Telephone Network PTZ Pan/Tilt/Zoom Q QoS Quality of Service R RM ResourceManager S SDI Serial Digital Interface SIP Session Initiation Protocol SMB SubMiniature version B connector SXGA Super Extended Graphics Array U USB Universal Serial Bus V VGA Video Graphics Array W WCDMA Wideband Code Division Multiple Access Wi-Fi Wireless Fidelity WOL Wake on LAN X XGA Extended Graphics A
