资 产 用 息 CT C 使 信 华 为 仅 散 供 HUAWEI ME906s LTE M.
Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved. 资 产 No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. and its affiliates ("Huawei"). The product described in this manual may include copyrighted software of Huawei and possible licensors.
HUAWEI ME906s LTE M.2 Module Hardware Guide About This Document 资 产 About This Document Revision History 01 2015-06-10 02 2015-07-23 用 Updated dimensions in Table 2-1 Features 2.2 3.4.2 Updated the test instrument 4.4.2 Updated Table 4-4 Conducted Tx power 5.4.1 Updated Table 5-4 Requirements for input current 5.5 Updated test duration of temperature cycle in Table 5-10 Test conditions and results of the reliability 6.2 Updated the dimensions 9.13.1 Updated section 9.13.
HUAWEI ME906s LTE M.2 Module Hardware Guide Contents 资 产 Contents 1 Introduction.................................................................................................................................... 7 2 Overall Description ...................................................................................................................... 8 息 2.1 About This Chapter ...........................................................................................................................
HUAWEI ME906s LTE M.2 Module Hardware Guide Contents 3.11.2 Coaxial RF Connector Guidelines ....................................................................................... 42 4 RF Specifications ......................................................................................................................... 45 4.1 About This Chapter ......................................................................................................................... 45 4.2 Operating Frequencies .......
HUAWEI ME906s LTE M.2 Module Hardware Guide Contents 9.6 Safety of Children ........................................................................................................................... 72 9.7 Environment Protection .................................................................................................................. 72 9.8 WEEE Approval .............................................................................................................................. 72 9.
HUAWEI ME906s LTE M.2 Module Hardware Guide Introduction 资 产 1 Introduction 用 息 This document describes the hardware application interfaces and air interfaces that are provided when HUAWEI ME906s LTE M.2 Module (hereinafter referred to as the ME906s module) is used. 使 CT C This document helps you to understand the interface specifications, electrical features and related product information of the ME906s module. 严 禁 扩 仅 散 供 华 为 信 M.
HUAWEI ME906s LTE M.2 Module Hardware Guide Overall Description 资 产 2 Overall Description 息 2.1 About This Chapter Function Overview Circuit Block Diagram CT C 2.2 Function Overview 用 使 Table 2-1 Features Feature 供 Physical Features Description Weight: about 6 g FDD LTE: Band 1, Band 2, Band 3, Band 5, Band 7, Band 8, Band 20, Band 28, all bands with diversity 扩 仅 Operating Bands Dimensions (L × W × H): 42 mm × 30 mm × 2.
HUAWEI ME906s LTE M.2 Module Hardware Guide Feature Overall Description Description Power_On_Off pin RESET# pin LED# pin 资 产 W_DISABLE# pin GPS_DISABLE# pin Tunable Antenna control (4 GPIOs) Wake_On_WWAN# pin 息 BodySAR_N pin Power supply (5 pins) MAIN and AUX (supports Diversity and GPS simultaneously) SMS Supports MO and MT Supports formats of PDU 使 华 为 信 用 Antenna Connectors Point-to-point and cell broadcast GPRS: DL 85.6 kbit/s; UL 85.6 kbit/s CT C Data Services EDGE: DL 236.
HUAWEI ME906s LTE M.2 Module Hardware Guide Overall Description Power manager Nand Flash Radio Frequency (RF) transceiver RF Front End 使 严 禁 扩 仅 散 供 CT C 华 为 信 用 息 资 产 Figure 2-1 Circuit block diagram Issue 04 (2017-12-11) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI ME906s LTE M.2 Module Hardware Guide 资 产 3 Description of the Application Interfaces Description of the Application Interfaces 息 3.1 About This Chapter 用 75-pin Gold Finger Power Interface Signal Control Interface USB Interface USIM Card Interface Tunable Antenna Control Config Pins Reserved Pins NC Pins RF Antenna Interface 散 供 CT C 使 仅 华 为 信 This chapter mainly describes the application interfaces of the ME906s module, including: 扩 3.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 信 用 息 资 产 Figure 3-1 TOP view of gold finger interface pins CT C 使 As M.2 Nomenclature, ME906s is Type 3042-S3-B (30 mm × 42 mm, Max. Component Height on Top is 1.5 mm and single-sided, Key ID is B). 严 禁 扩 仅 散 供 华 为 Table 3-1 shows the definitions of the 75-pin interface (67 for signals and 8 for notch) of the ME906s module.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Table 3-1 Definitions of pins on the M.2 interface Pad Type CONFIG_3 O 2 3.3V PI 3 Ground PI 4 3.3V PI 5 Ground PI - Power supply - 3.135 3.3 4.4 - Ground - - 0 - - Power supply - 3.135 3.3 4.4 - Ground - - 0 - - 1.26 - 3.6 VIL –0.3 - 0.3 The module is pulled down inside by a 1 MΩ resistor. - - - - - - 3.6 A single control to turn On/Off WWAN.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Pin Name Pad Type Description Parameter Min. (V) Typ. (V) Max. (V) Comments 14 Notch - - - - - - - 15 Notch - - - - - - - 16 Notch - - - - - - - 17 Notch - - - - - - - 18 Notch - - - - - - - 19 Notch - - - - - - - 20 Reserved - Reserved for future use, please keep it not connected in the host side.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Pin Name Pad Type Description Parameter Min. (V) Typ. (V) Max. (V) Comments 29 NC - Not Connected - - - - - VOH 0.7 x USIM _PW R - 3.3 O NC - USIM Reset Not Connected PI I/O 36 37 NC USIM_PWR NC Issue 04 (2017-12-11) - PO - - - - VOH 0.7 x USIM _PW R - 3.3 VOL 0 - 0.2 x USIM _PW R - - 0 - VOH 0.7 x USIM _PW R - 3.3 - 0.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Pin Name Pad Type Description Parameter Min. (V) Typ. (V) Max. (V) Comments 38 NC - Not Connected - - - - - 39 Ground PI Ground - - 0 - - VIH 1.26 1.8 2.1 VIL –0.3 - 0.63 - - - - - VOH 1.35 1.8 - VOL 0 - 0.45 VIH 1.26 1.8 2.1 VIL –0.3 - 0.63 The current firmware does not support this function. - - - - VIH 1.26 1.8 2.1 VIL –0.3 - 0.63 - 0 - 1.6 1.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Pin Name Pad Type Description Parameter Min. (V) Typ. (V) Max.
HUAWEI ME906s LTE M.2 Module Hardware Guide Pad Type Pin Name Description USIM hot swap detection pin. USIM_DET I Not Connected 2.1 VIL –0.3 - 0.3 VIH 1.26 - 2.1 VIL –0.3 - 0.3 - - - - - - - 3.135 3.3 4.4 - Ground - - 0 - - 72 3.3V PI Power supply - 3.135 3.3 4.4 - 73 Ground PI Ground - - 0 - - 74 3.3V - 3.135 3.3 4.4 - - The module is configured as WWANSSIC 0. 使 PI CT C Ground - 供 71 Power supply - - 扩 Connected to Ground internally.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 3.3 Power Interface 3.3.1 Overview The power supply part of the ME906s module contains: 3.3V pin for the power supply USIM_PWR pin for USIM card power output 资 产 Table 3-2 lists the definitions of the pins on the power supply interface. Table 3-2 Definitions of the pins on the power supply interface 3.3V 信 USIM_PWR 3, 5, 11, 27, 33, 39, 45, 51, 57, 71, 73 Ground PO Parameter Min. (V) Typ. (V) Max.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-2 Recommended power circuit 3.3V 3.3V + Module (Modem) 息 资 产 330 pF 100 nF 1 μF 22 μF 220 μF 信 用 3.135 V is the minimum voltage supplied to ME906s by the host, and 3.3V pin must never be under 3.135 V in any case, which is shown as the following figure. 使 4.4V Do not drop below 3.135 V during 2G Tx. The maximum current may be 2.5 A@3.3 V. 3.3V Time 扩 仅 散 供 3.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Remarks 3.3.3 USIM Power Output USIM_PWR Time (Min.) Unit 100 ms 散 Power off time 供 Toff 使 Parameter CT C 华 为 信 用 息 资 产 Figure 3-3 Power supply timing sequence between power cycling 严 3.4.1 Overview 禁 3.4 Signal Control Interface 扩 仅 Through the USIM_PWR power supply interface, the ME906s module can supply 1.8 V or 3.0 V power to USIM card.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces BodySAR detection (BodySAR_N) pin USIM detection (USIM_DET) pin Table 3-3 lists the pins on the signal control interface. Table 3-3 Pins on the signal control interface Pad Type Pin Name Description 资 产 Pin No. Parameter Min. (V) Typ. (V) Max. (V) Comments VIH 1.26 - 3.6 VIL –0.3 - 0.3 The module is pulled down inside by a 1MΩ resistor. 1.26 - 2.1 –0.3 - 0.
HUAWEI ME906s LTE M.2 Module Hardware Guide Pin No. Pad Type Pin Name Description of the Application Interfaces Description Hardware pin for BodySAR Detection. 25 BodySAR_N I 资 产 When it is High, USIM is present. VIH 1.26 - 3.6 VIL –0.3 - 0.3 VIH 1.26 1.8 2.1 Comments - 0.3 The module is pulled up inside. 用 信 –0.3 VIL When it is Low, USIM is absent. 使 3.4.2 Power_On_Off Control Pin CT C The ME906s module can be controlled to be powered on/off by the Power_On_Off pin.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-4 Recommended connections of Power_On_Off pin (auto power) ME906s 3.3V Pin2, 4, 70, 72, 74 47 kΩ 资 产 Power_On_Off 息 Pin6 Power on sequence 用 使 CT C Figure 3-5 Recommended power on timing sequence 3.3V 供 华 为 信 Do not toggle RESET# during power on sequence. Pulling RESET# low will extend time for module startup. Recommended power on timing sequence is shown as Figure 3-5 .
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-6 Recommended power off timing sequence (cut off 3.3 V) 资 产 3.3V RESET# 息 Power_On_Off 用 信 Power off 使 For use case ME906s is connected directly to battery, such as tablet platforms, Power_On_Off should be controlled by a GPIO from the host to control ME906s to be powered on/off.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Do not toggle RESET# during power on sequence, pulling RESET# low will extend time for module startup. The recommended power on timing sequence is shown as Figure 3-8 . Figure 3-8 Recommended power on timing sequence 资 产 3.3V (battery always on) 息 RESET# Power off sequence 用 Power on 使 t0 ≥ 0ms CT C t0 Keep Power_On_Off logic low for more than 500 ms to shut off the module.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-10 Recommended warm boot timing in the notebook/tablet 3.3V (battery, always on) 资 产 . RESET# Power_On_Off 息 t2 用 信 使 If there is a limitation on the controlling GPIO to be programmable 500 ms, the hardware solution as shown in Figure 3-11 can be used. Module CT C Figure 3-11 Power on off circuit (hardware solution) HOST Power_On_Off Pin 6 Q1 1MΩ 散 NMOS 扩 仅 GPIO2 3.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 3.4.3 RESET# Pin The ME906s module can be reset through the RESET# pin asynchronous, active low. Whenever this pin is active, the module will immediately be placed in a Power On reset condition. Care should be taken for this pin unless there is a critical failure and all other methods of regaining control and/or communication with the WWAN subsystem have failed.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces VCCGPIO1 Module HOST RESET# Pin 67 1MΩ NMOS 资 产 33рF NMOS 0Ω 用 信 息 GPIO1 使 GPIO is not high-impedance when the host is powered off. CT C Use only one N-MOSFET, in this case the logic of RESET# and GPIO1 is reversed.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 3.4.4 LED# Pin ME906s provides an open drain signal to indicate the RF status. Table 3-5 State of the LED# pin Operating Status LED# 1 RF function is turned on Output Low, current sink 2 RF function is turned off Output High 资 产 No. 息 Figure 3-12 shows the recommended circuits of the LED# pin.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-13 Connections of the W_DISABLE# pin Module (Modem) VCC From Host 1.8V 资 产 10 kΩ Host BB Chip 用 信 息 W_DISABLE# CT C ME906s provides a hardware pin (GPS_DISABLE#) to disable or enable the GPS. In addition, the GPS can also be enabled or disabled through software AT commands. Table 3-7 Function of the GPS_DISABLE# pin No. GPS_DISABLE# Function 1 Low GPS function is disabled.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces It is recommended not to add a diode on the GPS_DISABLE# pin outside the module. 资 产 3.4.7 Wake_On_WWAN# Pin ME906s provides an open drain output Wake_On_WWAN# pin to wake up the host, which is low active. 用 息 Figure 3-15 Wave form of the Wake_On_WWAN# pin 使 CT C Figure 3-16 Connections of the Wake_On_WWAN# pin 10 kΩ 3.4.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces No. BodySAR_N Function 2 High Max. TX power will NOT be backed off (default). 3 Floating Max. TX power will NOT be backed off. 资 产 If BodySAR_N pin is used to monitor the proximity sensor output directly, there are some essential preconditions for this hardware solution.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-18 Connections of the USIM_DET pin USIM Deck 1.8V CD 资 产 Module (Modem) BB Chip USIM_DET 470 pF 信 用 息 If USIM card is absent, the CD connects to Ground. If USIM card is present, the CD is open. 使 CT C It is recommended not to add a diode on the USIM_DET pin outside the module. The normal SHORT USIM connector should be employed. The logic of USIM_DET is shown as Figure 3-19 .
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-19 Logic of USIM_DET WWAN Module 1.8V USIM Connector Switch 资 产 USIM installed= Not Connected USIM_DET Modem Processor 信 用 息 USIM not installed= GND Pin Name I/O Description CT C Pin No. 使 The ME906s is compliant with USB 2.0 high speed protocol. The USB input/output lines are following USB 2.0 specifications.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces Figure 3-21 USB D+ and 3.3V power on timing sequence 资 产 3.3V Power_On_Off 息 Tpd 用 Remarks Tpd Power valid to USB D+ high 使 Parameter Time (Nominal value) Unit 6 s CT C 华 为 信 USB D+ 散 供 The layout design of this circuit on the host board should comply with the USB 2.0 high speed protocol, with differential characteristic impedance of 90 Ω. 仅 3.6 USIM Card Interface 扩 3.6.
HUAWEI ME906s LTE M.2 Module Hardware Guide USIM_CLK Description O 息 Max. (V) VOH 0.7 x USIM _PW R - 3.3 VOL 0 - 0.2 x USIM _PW R VOH 0.7 x USIM _PW R - 3.3 - 0.2 x USIM _PW R VOL USIM DATA P USIM_DET I 3.3 严 When it is High, USIM is present. USIM_PWR =1.8 V or 3.0 V 0 - - 1.75 1.8 1.98 USIM_PWR =1.8 V USIM_PWR =3.0 V - Rising edge for insertion; falling edge for removal. - USIM_P WR=1.8 V or 3.0 V VIL USIM POWER USIM hot swap detection pin. 0.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 使 The ESD protection component should choose low capacitance. The capacitance of the component should be lower than 10 pF. To meet the requirements of 3GPP TS 51.010-1 protocols and electromagnetic compatibility (EMC) authentication, the USIM socket should be placed near the M.2 interface (it is recommended that the PCB circuit connects the M.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces O O ANTCTL3 Min. (V) Typ. (V) Max. (V) Comments Tunable antenna control signal, bit 0. VOH 1.37 1.8 2.1 - It is a push-pull type GPIO. VOL 0 - 0.45 - Tunable antenna control signal, bit 1. VOH 1.37 1.8 2.1 - It is a push-pull type GPIO. VOL 0 - 0.45 - Tunable antenna control signal, bit 2. VOH 1.37 1.8 2.1 - It is a push-pull type GPIO. VOL 0 - 0.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces In the M.2 spec, the 4 pins are defined as shown in Table 3-13 . Table 3-13 List of Config pins Config_1 (Pin 69) Config_2 (Pin 75) Config_3 (Pin 1) Module type and Main host interface Port Configuration NC Ground Ground Ground WWAN-SSIC 0 资 产 Config_0 (Pin 21) 息 The GPIO0–7 pins have configurable assignments. There are 4 possible functional pin out configurations.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 3.10 NC Pins The module has some NC pins. All of NC pins are not connected in the module. Table 3-16 List of NC pins Pin Name Pad Type 29, 31, 35, 37, 38, 41, 43, 47, 49, 50,52, 53, 54, 55, 56, 58, 68 - Not Connected Description 资 产 Pin No. 息 - Max. (V) Comments - - - - - 用 Typ. (V) CT C ME906s module provides 2 antenna connectors for connecting the external antennas.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 3.11.2 Coaxial RF Connector Guidelines The antenna interface must be used with coaxial cables with characteristic impedance of 50 Ω. The ME906s module supports the buckled RF connector antenna connection methods: buckled RF connector 818000500 by ECT, RFC43-1K2600 by ACON or other equivalent connectors. 资 产 Figure 3-24 shows the RF connector dimensions.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 使 CT C Figure 3-26 Connection between the RF connector and the 0.81 mm cable 散 供 华 为 信 用 息 资 产 Figure 3-25 Specifications of 0.81 mm coaxial cable mating with the RF connector 严 禁 扩 仅 Figure 3-27 Specifications of 1.13 mm coaxial cable mating with the RF connector Issue 04 (2017-12-11) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description of the Application Interfaces 使 严 禁 扩 仅 散 供 CT C 华 为 信 用 息 资 产 Figure 3-28 Connection between the RF connector and the 1.13 mm cable Issue 04 (2017-12-11) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI ME906s LTE M.2 Module Hardware Guide 资 产 RF Specifications 4 RF Specifications 息 4.1 About This Chapter 用 Operating Frequencies Conducted RF Measurement Conducted Rx Sensitivity and Tx Power Antenna Design Requirements 使 CT C 华 为 信 This chapter describes the RF specifications of the ME906s module, including: 4.2 Operating Frequencies 供 Table 4-1 shows the RF bands supported by ME906s.
HUAWEI ME906s LTE M.2 Module Hardware Guide RF Specifications Tx Rx LTE Band 5 824 MHz–849 MHz 869 MHz–894 MHz LTE Band 7 2500 MHz–2570 MHz 2620 MHz–2690 MHz LTE Band 8 880 MHz–915 MHz 925 MHz–960 MHz LTE Band 20 832 MHz–862 MHz 791 MHz–821 MHz 资 产 Operating Band 703 MHz–748 MHz 758 MHz–803 MHz GPS L1 - 1574.42 MHz–1576.42 MHz GLONASS L1 - 1597.55 MHz–1605.89 MHz 息 LTE Band 28 信 用 4.
HUAWEI ME906s LTE M.2 Module Hardware Guide RF Specifications Table 4-2 Conducted Rx sensitivity Typical Value (Unit: dBm) Note GSM 850 –109 BER Class II < 2.44% GSM 900 –109 BER Class II < 2.44% GSM 1800 –109 BER Class II < 2.44% GSM 1900 –109 BER Class II < 2.44% UMTS Band 1 –111 BER < 0.1% UMTS Band 2 –111 BER < 0.1% UMTS Band 5 –111.5 BER < 0.1% UMTS Band 8 –111.5 BER < 0.
HUAWEI ME906s LTE M.2 Module Hardware Guide RF Specifications The test values are the average of some test samples. LTE sensitivity is tested in SIMO (Main + AUX). The circular error probability for GPS value is 50%. 4.4.2 Conducted Transmit Power 资 产 The conducted transmit power is another indicator that measures the performance of ME906s. The conducted transmit power refers to the maximum power that the module tested at the antenna port can transmit.
HUAWEI ME906s LTE M.2 Module Hardware Guide RF Specifications Maximum Power Reduction (MPR and AMPR) of LTE is according to 3GPP TS 36.521-1. 4.5 Antenna Design Requirements Antenna Efficiency 资 产 4.5.
HUAWEI ME906s LTE M.2 Module Hardware Guide RF Specifications To avoid this problem, evaluate the antenna isolation as sufficiently as possible at the early stage of antenna design. Antenna isolation depends on the following factors: Distance between antennas Antenna type Antenna direction 资 产 The primary antenna must be placed as near as possible to the ME906s to minimize the cable length. The secondary antenna needs to be installed perpendicularly to the primary antenna.
HUAWEI ME906s LTE M.2 Module Hardware Guide RF Specifications antenna into account. The appropriate antenna gain prolongs the service life of relevant batteries. The following antenna gain is recommended for ME906s. Gain of the primary antenna ≤ 2.5 dBi Gain of the secondary antenna ≤ 2.5 dBi ECC of the antenna 资 产 ECC is short for Envelope Correlation Coefficient. It is the cross-correlation value of the complex patterns of the master and diversity antenna.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.2 Module Hardware Guide 资 产 5 Electrical and Reliability Features Electrical and Reliability Features 息 5.1 About This Chapter 用 Absolute Ratings Operating and Storage Temperatures Power Supply Features Reliability Features EMC and ESD Features 使 CT C 华 为 信 This chapter describes the electrical and reliability features of the interfaces in the ME906s module, including: 扩 仅 散 供 5.2 Absolute Ratings Symbol Specification Min. Max. Unit 3.
HUAWEI ME906s LTE M.2 Module Hardware Guide Electrical and Reliability Features Table 5-2 Operating and storage temperatures Min. Max. Unit Normal operating temperature –10 +55 °C Extended operating temperature[1] –20 +70 °C Ambient storage temperature –40 +85 °C 资 产 Specification 息 [1]: When the ME906s module works at –20°C to –10°C or +55°C to +70°C, NOT all its RF specifications comply with the 3GPP specifications. 5.4 Power Supply Features 用 信 5.4.
HUAWEI ME906s LTE M.2 Module Hardware Guide Electrical and Reliability Features 5.4.2 Power Consumption The power consumption of ME906s in different scenarios are respectively listed in Table 5-5 to Table 5-9 . 资 产 The power consumption listed in this section are tested when the power supply of ME906s module is normal voltage (3.3 V), and all of test values are measured at room temperature.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description Electrical and Reliability Features Bands Test Value (Unit: mA) Notes/Configuration Typical Idle LTE LTE bands 55 Module is powered up. DRX cycle=8 (2.56s) 资 产 UMTS bands Module is powered up. DRX cycle=8 (2.56s) Module is registered on the network, and no data is transmitted. 60 使 GSM bands 用 USB is in active. All bands 55 MFRMS=5 (1.175s) Module is registered on the network, and no data is transmitted. Module is powered up.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description Electrical and Reliability Features Band Test Value (Unit: mA) Notes/Configuration Typical 200 1 dBm Tx Power (900 MHz) 260 10 dBm Tx Power 679 23.5 dBm Tx Power 资 产 Band 8 212 1 dBm Tx Power (IMT2100) 260 10 dBm Tx Power 695 23.5 dBm Tx Power Band 2 214 1 dBm Tx Power (PCS 1900) 261 10 dBm Tx Power 730 23.5 dBm Tx Power 212 (850 MHz) 243 Band 8 仅 214 1 dBm Tx Power Band 2 243 10 dBm Tx Power 701 23.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.2 Module Hardware Guide Description Electrical and Reliability Features Test Value (Unit: mA) PCL Notes/Configuration Typical 275 2 Up/1 Down 373 4 Up/1 Down 10 1 Up/1 Down 资 产 120 151 2 Up/1 Down 218 4 Up/1 Down 息 All power consumption test configuration can be referenced by GSM Association Official Document TS.09: Battery Life Measurement and Current Consumption Technique. 用 Test condition: for max. Tx. power, see 4.4.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.2 Module Hardware Guide Standard Sample size Results Frequency range: 5 Hz to 200 Hz JESD22B103-B 3 pcs/group Visual inspection: ok Acceleration: 1 Grms Frequency scan rate: 0.5 oct/min Test duration: 3 axial directions. 2 h for each axial direction. Operation mode: working with service connected Half-sine wave shock JESDB104-C Shock duration: 11 ms Test duration: 6 axial directions. 3 shocks for each axial direction.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.2 Module Hardware Guide Electrical and Reliability Features The following are the requirements of ESD environment control: The electrostatic discharge protected area (EPA) must have an ESD floor whose surface resistance and system resistance are greater than 1 x 104 Ω while less than 1 x 109 Ω. The EPA must have a sound ground system without loose ground wires, and the ground resistance must be less than 4 Ω.
HUAWEI ME906s LTE M.2 Module Hardware Guide 资 产 6 Mechanical Specifications Mechanical Specifications 息 6.1 About This Chapter Dimensions Packing System 用 使 华 为 信 This chapter describes the following aspects of the ME906s module: CT C 6.2 Dimensions Figure 6-1 shows the dimensions of ME906s in details. 严 禁 扩 仅 散 供 Figure 6-1 Dimensions (Unit: mm) Issue 04 (2017-12-11) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
HUAWEI ME906s LTE M.2 Module Hardware Guide Mechanical Specifications 6.3 Packing System ME906s package includes the blister tray, the blister tray cover, and the carton (with bottom and top clapboard). 资 产 The blister tray of the ME906s module package is as shown in the following figure. There are 75 pcs modules for every tray, 6 pcs trays in one carton, and 450 pcs modules for every carton. And the blister tray cover covers the top tray.
HUAWEI ME906s LTE M.2 Module Hardware Guide Installation 资 产 7 Installation 息 7.1 About This Chapter Connect ME906s to board Thermal Management Antenna Plug 用 使 华 为 信 This chapter describes the assembly of ME906s, including: CT C 7.2 Connect ME906s to board Figure 7-1 Install the module It refers to M.2 specification. 扩 仅 散 供 HUAWEI M.2 Module 禁 The module will need a mechanical retention at the end of the board. The module specifies a 5.5 mm Dia.
HUAWEI ME906s LTE M.2 Module Hardware Guide Installation 7.3 Thermal Management Because ME906s is very small, the dissipating heat is very important to it. It has to take several means to ensure ME906s to meet the specification. The methods described as follow: The mounting screw is to hold the module in place, and connect the heat source to the platform ground plane of the custom board.
HUAWEI ME906s LTE M.2 Module Hardware Guide Installation 资 产 Figure 7-3 Unmating the plug The extraction tool is recommended. Any attempt of unmating by pulling on the cable may result in damage and influence the mechanical / electrical performance. 息 It is recommended not to apply any pull forces after the bending of the cable, as described in Figure 7-4 .
HUAWEI ME906s LTE M.2 Module Hardware Guide Certifications 资 产 8 Certifications 息 This chapter gives a general description of certifications of ME906s. 信 用 Table 8-1 Product certifications Certification ME906s-158 使 FCC RCM EU RoHS 供 PVC-Free Halogen-free 扩 仅 GCF 散 NCC CT C 华 为 CE 严 禁 Table 8-1 shows certifications the module has been implemented. For more demands, please contact us for more details about this information.
HUAWEI ME906s LTE M.2 Module Hardware Guide Safety Information 资 产 9 Safety Information 信 用 息 Read the safety information carefully to ensure the correct and safe use of your wireless device. Applicable safety information must be observed. 使 Power off your wireless device if using the device is prohibited. Do not use the wireless device when it causes danger or interference with electric devices. CT C 华 为 9.1 Interference 9.
HUAWEI ME906s LTE M.2 Module Hardware Guide Safety Information Area indicated with the "Power off bi-direction wireless equipment" sign Area where you are generally suggested to stop the engine of a vehicle 9.4 Traffic Security Observe local laws and regulations while using the wireless device. To prevent accidents, do not use your wireless device while driving. RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer.
HUAWEI ME906s LTE M.2 Module Hardware Guide Safety Information 9.10 Laws and Regulations Observance Observe laws and regulations when using your wireless device. Respect the privacy and legal rights of the others. 资 产 9.11 Care and Maintenance It is normal that your wireless device gets hot when you use or charge it. Before you clean or maintain the wireless device, stop all applications and power off the wireless device. Use your wireless device and accessories with care and in clean environment.
HUAWEI ME906s LTE M.2 Module Hardware Guide Safety Information The most recent, effective version of the DoC (Declaration of Conformity) can be viewed at http://consumer.huawei.com/certification. This device may be operated in all member states of the EU. Observe national and local regulations where the device is used. This device may be restricted for use, depending on the local network.
HUAWEI ME906s LTE M.2 Module Hardware Guide Safety Information 使 严 禁 扩 仅 散 供 CT C 华 为 信 Reorient or relocate the receiving antenna. Increase the distance between the device and the receiver. Connect the device to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. This device is intended for OEM integrators only.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.
HUAWEI ME906s LTE M.2 Module Hardware Guide Appendix B Acronyms and Abbreviations Expansion UMTS Universal Mobile Telecommunications System USB Universal Serial Bus USIM Universal Subscriber Identity Module VSWR Voltage Standing Wave Ratio 资 产 Acronym or Abbreviation Wideband Code Division Multiple Access 使 严 禁 扩 仅 散 供 CT C 华 为 信 用 息 WCDMA Issue 04 (2017-12-11) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
