Copyright © 2008 Huawei Technologies Co., Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The information in this document is subject to change without notice.
Table of Contents Getting to Know the EG162G ................................................ 1 Requirements for the Computer ............................................ 2 Preparing the EG162G ......................................................... 2 Installation Guide................................................................ 4 Safety Information ..............................................................
Thank you for purchasing Huawei EG162G USB Stick (hereinafter referred to as the EG162G). Note: This manual briefs the profiles of EG162G, including the preparation, installation/uninstall process, and safety precautions. You are highly recommended to read the manual before using the EG162G. The actual signal strength and the transmission rate are affected by the environment. The electromagnetic wave emitted from the PC or laptop may cause disturbance to wireless signals.
USB connector Connects to the USB interface of the computer. SIM card slot Fixes and bears the SIM card. Indicator It indicates the status of the EG162G. Green, blinking twice every 3s: The EG162G is powered on. Green, blinking once every 3s: The EG162G is registered to a GSM/GPRS/EDGE network. Green, always on: The GSM/GPRS/EDGE connection is set up. Blue, always on: SIM card is not installed. SIM card is invalid. PIN code is required.
requirements for running the installed OS Display resolution: 800 × 600 or above Preparing the EG162G 1. Press the right and left side of the cover, remove it, and take out the SIM card slot. 2. Insert the SIM card into the card slot, with the contact area on the card is facing down and the beveled corner on the card is facing inwards. Make sure that the SIM card is fully in place. 3. Insert the card slot with the SIM card into the EG162G.
Installation Guide The procedure for installing the management program is subject to the operating system installed on your laptop. The following section takes Windows XP as an example. Installing the EG162G 1. Connect the EG162G to the USB interface of the computer. 2. The OS auto detects and recognizes new hardware and starts the installation wizard.
Note: If the auto-run program does not respond, go to the driver path. Find and double-click the AutoRun.exe, and then the program will run. 3. Follow the prompts of the installation wizard. 4. After the program is installed, the shortcut icon for management program is displayed on the desktop. Launching the Management Program After the EG162G is installed, management program is launched automatically.
Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device. Interference Do not use your wireless device if using the device is prohibited or when it cause danger or interference with electric devices. Medical Device Do not use your wireless device and follow the rules and regulations set forth by the hospitals and health care facilities. Some wireless devices may affect the performance of the hearing aids.
Area indicated with the "Explosives" sign Area indicated with the "Power off bi-direction wireless equipment" sign Area where you are generally suggested to stop the engine of a vehicle Traffic Security Observe local laws and regulations while using the wireless device. To prevent accidents, do not use your wireless device while driving. RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer.
relevant provisions of the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE Directive). RoHS Approval The wireless device is in compliance with the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive 2002/95/EC (RoHS Directive). Laws and Regulations Observance Observe laws and regulations when using your wireless device. Respect the privacy and legal rights of the others.
Use only accessories of the wireless device approved by the manufacture. Contact the authorized service center for any abnormity of the wireless device or accessories. Do not dismantle the wireless device or accessories. Otherwise, the wireless device and accessories are not covered by the warranty. Emergency Call This wireless device functions through receiving and transmitting radio signals. Therefore, the connection cannot be guaranteed in all conditions.
Body Worn Operation Important safety information regarding radiofrequency radiation (RF) exposure To ensure compliance with RF exposure guidelines the device must be used with a minimum of 1.5 cm separation from the body. Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits. Regulatory Information The following approvals and notices apply in specific regions as noted.
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
12
