Wonderful Communication, Mobile Life. Welcome to HUAWEI ETS2029/2229/2529 Fixed Wireless Terminal.
Copyright © 2007 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this manual are the property of their respective holders. Notice The information in this manual is subject to change without notice.
Table of Contents 1 Warnings and Precautions .....................................................................................................1 2 Introduction ...........................................................................................................................5 Packing List ...................................................................................................................5 Appearance of the FWT ........................................................................
Editing a Contact .........................................................................................................24 Deleting a Contact .......................................................................................................25 Copying a Contact .......................................................................................................25 Groups..........................................................................................................................
1 Warnings and Precautions Before using the HUAWEI Fixed Wireless Terminal (hereinafter referred to as FWT), read the following cautions and let your children know these, so that you can use your FWT correctly and safely. Basic Cautions According to the packing list, check items in the package box to make sure that they are complete and undamaged. Before installing and using FWT, read the user manual carefully.
Operating Environment y Do not place magnetic storage media such as magnetic cards and floppy disks near the FWT. Radiation from the FWT may erase the information stored on them. y Do not put your FWT, battery, or other accessories in containers with strong magnetic field, such as the induction cooker and microwave oven. Otherwise, circuit failure, fire, or explosion may result.
Emergency Call You can use your FWT for emergency calls. However, connections in all conditions cannot be guaranteed. You should never rely solely on the FWT for essential communications. Battery y If the battery fluid gets into eyes, do not rub them. Wash with clean water and seek medical assistance immediately. y If the battery fluid contacts skin or cloth, wash with clean water immediately to avoid irritation to the skin. y Do not dispose of the battery in fire.
Environmental Protection Abide by the local laws in disposing of the package materials of your FWT, consumed batteries and used FWT, and try to recycle them. Please observe the national local regulations in the location where product is to be used. This product may be restricted for use in some or all countries of European Union. Statement y This device complies with part 15 of the FCC Rules.
2 Introduction Packing List The FWT package box contains the following items. If any of the items is lost or damaged, contact your local dealer.
Appearance of the FWT Front View 1 2 14 3 13 4 5 6 7 8 9 12 No. Item 1 Display screen 2 Left soft key 10 Description To display information. z z z 6 11 In the standby mode, press it to access the main menu. In the non-standby mode, press it to perform the operation displayed on the lower left corner of the screen. Press this key to answer a call.
No. 3 Item Scroll key Description z Up key: In the standby mode, press it to access the Calendar screen; during a call, press it to increase the z Down key: In the standby mode, press it to enable the radio (or alarm clock); during a call, press it to decrease the volume. Left key: In the standby mode, press it to view the call records. Right key: In the standby mode, press it to access the Write message screen. In the standby mode, press it to access the Phone Book screen.
No. Item Description In the standby mode, press and hold it repeatedly to activate/cancel the quiet profile. Press it repeatedly to enter a symbol and so on. 11 * key z 12 Number keys Press 0–9 keys to enter numbers/characters or speed dial a phone number. 13 Handset retaining clip When the FWT is wall-mounted, it is used it to fix the handset. 14 Heaver End the current call or other operations.
No Item Description 8 Coiled cord jack on handset To connect to the handset coiled cord. 9 Handset To make a call or answer a call by lifting it. 10 Antenna jack To connect to the antenna 11 DB9 serial port To maintain the FWT through it. 12 Power jack To connect to the power adapter for power supply. Icons Icon Description Indicates the signal strength. The more the bars, the stronger the signal strength. Indicates there is a new message. Indicates there is a new voice message.
3 Installation Installing the UIM Card (Optional) Caution: y Consult your service provider to decide whether to use a user identity module (UIM) card. y The UIM card and its golden contact can be easily damaged by a scratch or bend. Be careful when installing or removing the UIM card. Press and hold to power your FWT off and then disconnect it from the power socket. Install the UIM card according to the following figure. Make sure that the golden contact of the UIM card is facing downwards.
y If the FWT is powered solely by the spare battery, the talk time is three hours to five hours or the standby time is 40 hours to 120 hours (the talk time and the standby time are network dependent). Installing the Power Adapter to power off your FWT. Connect the power adapter to the FWT, and Press and hold plug it to the power socket. Installing the Spare Battery Press and hold to power off your FWT and then disconnect the FWT from the power socket.
Checking the Signal Strength 1. 2. 3. to power on your FWT. Wait until After installing the antenna, press and hold the signal strength icon appears or you can hear the dialing tone when you lift the handset. If the signal strength icon does not appear after five minutes or you hear the failure tone when you lift the handset, it indicates that the FWT is not receiving signals. In this case, you need to adjust the direction of the antenna until you can hear the dialing tone on lifting the handset.
2. According to the distance between the two hooks (7.7 cm), hammer two nails into the wall with 3 mm end left out. 7. 7cm 3. Snap the hooks to the nails. Validating After installing the FWT, you can make a call to check whether it is correctly installed. 1. Press and hold 2. 3. socket, the icon appears, indicating that the FWT is powered normally. appears normally. Lift the handset.
4 Basic Operations Powering the FWT On or Off When the FWT is powered off, press and hold In the standby mode, press and hold to power it on. to power it off. Making a Call Making a Call Through the Keypad 1. In the standby mode, press number keys to enter a phone number. If the entered phone number is wrong, press 2. Press 3. Press . to dial the phone number. to end the call or cancel the dialing. Making a Call from the Dialed Calls List 1. 2.
You can only set the speed dial function for contacts saved in the FWT. 1. 2. Select Menu > Phone Book > Speed Dial. Press the Up/Down key to scroll up or down the items. 3. If a number key is not assigned to a contact, press phone book. 4. If a number key is assigned to a contact, press y Change: Change a contact. y to select a contact from the for the following options: Delete: Delete the contact. Answering a Call In the standby mode, you can lift the handset, press , or to answer a call.
y Phone Book: Access the Phone Book screen. y Messages: Access the Messages screen. y Third Party Call: The function is network dependent. For details, consult your service provider. y Voice Privacy: The function is network dependent. For details, see "Voice Privacy" on page 27. Locking the Keypad Even when the keypad is locked, you can lift the handset, press answer a call. or press to Locking the Keypad Manually Press and hold the # key for two seconds to lock the keypad.
5 Text Entry Text Input Mode While entering text, you can press the # key to change the input mode. The following table lists the input modes and their indicators. Indicator Text Input Mode eZiEn Smart English ABC English upper case abc English lower case 123 Numbers Note: In the edit mode, press Press and hold once to delete the letter on the left of the cursor. for over two seconds to delete all letters.
Note: y After you enter several letters, the FWT can give other letters to make out the candidate words. Press the Up/Down key or the * key to scroll the words and press the right key to confirm; or press number keys to enter letters. y Press repeatedly the 1 key to enter full stop. y Press the 0 key to enter a space. y Press the * key to display the symbol list. y Press the # key to change the case of letters.
6 Messages Writing and Sending a Message 1. Select Menu > Messages > Write Message. 2. y Write the message. When writing the message, you can press operations: Insert Templates: Insert a commonly used phrase. y Insert Phone Number: Insert a contact number from the phone book. for the following for the following operations: 3. After writing the message, press y Priority: Set the priority for messages sent from the short message service center (SMSC). y Send: Send the message.
icon blinks, it indicates that the message memory is full. Do the screen. If the following to view the inbox: 1. 2. Select Menu > Messages > Inbox. Press the Up/Down key to scroll up or down the messages. 3. Press (View) to view the message. 4. Press (Options) to select Reply, Delete, Forward, Call or Save Number. Viewing the Outbox and the Draft The outbox stores messages that are sent successfully. You can delete, forward or re-send a message in the outbox.
2. Select Call Voice Mail Center and press (Select) to call the voice mail center. Setting or Viewing the Voice Mail Number 1. 2. Select Menu > Messages > Voice Mail > Voice Mail Number. If the voice mail number is already set, you can view and edit it; if not, enter the voice mail number and press (OK). Note: The voice mail function is network dependent. You must subscribe for the service. For the voice mail number and other information, consult your service provider.
Setting the Auto Save Function Select Menu > Messages > Message Settings > Auto Save to set the auto save function. You can select: y Send And Save: Activate the auto save function. Messages are automatically saved after being sent. Messages sent successfully are saved to the outbox. Messages not sent are saved to the draft. y Send Only: Deactivate the auto save function. Setting the Auto Delete Function Select Menu > Messages > Message Settings > Auto Delete. y On: Activate the auto delete function.
Setting the Validity Period Select Menu > Messages > Message Settings > Validity Period. Then select Forever, After 12 Hours, After 1 Day or After 3 Days to set the validity period of messages. Setting the New Message Alert Select Menu > Messages > Message Settings > New Message Alert. Then select Off, 5 Minutes, 10 Minutes, 20 Minutes or 30 Minutes to set the time for alerting new messages. Setting the Delivery Ack Select Menu > Messages > Message Settings > Delivery Ack.
7 Phone Book Adding a Contact A contact is saved to the memory in use. 1. Select Menu > Phone Book > Add New. 2. 3. Enter the name and press Set other options: y If the memory in use is the FWT, you can set: Name, General Number, Home (OK). Number, Office Number, and Memo (you need to set at least one phone number). y If the memory in use is the UIM card, you can set General Number only. 4. Press (OK) to save the settings and press the Up/Down key to set other items. 5.
2. Press (Options) and select Edit to edit a contact. 3. Press (Save) to save the contact or press (Back) to cancel. Deleting a Contact Delete a Contact 1. Select Menu > Phone Book > Search to search for a contact to delete. 2. Press (Options) and select Delete. 3. Press (Yes) to delete the contact or press (No) to cancel. Delete All Contacts 1. Select Menu > Phone Book > Delete All. (OK). 2.
3. Press (Yes) to copy the contacts or press (No) to cancel. Groups You can sort contacts into different groups for easy management. You can set up to 10 groups. 1. 2. Select Menu > Phone Book > Groups. Press the Up/Down key to scroll up or down the groups. (Options) for the following options: 3. Press y View: View the contacts of a group. y Add: Add a contact to the group. y Group Ring: Set a ring tone for the incoming calls of the group members. y Rename: Rename the group.
8 Settings Call Settings Minute Alert If the minute alert function is activated, your FWT notifies you of the call duration by giving an alert 10 seconds before the end of each minute. 1. Select Menu > Settings > Call Settings > Minute Alert. 2. Select one of the following options: y On: Activate the minute alert function. y Off: Deactivate the minute alert function. Voice Privacy The voice privacy function can protect your conversion from interception. The voice privacy function is network dependent.
Shortcut Key Settings The FWT provides shortcut keys for your convenience. Note: In the standby mode, the default shortcut key settings are shown as follows: y : press it to access the Calendar screen; during a call, press it to increase the volume. : press it to enable the radio (or alarm clock); during a call, press it to y decrease the volume. y : press it to view the call records. y : press it to access the Write message screen.
(Select) and select Edit to edit a profile. You can set the following items: 3. Press y Volume: Adjust the volume of Ring and Key. y Incoming Call: Select a ring tone for incoming calls. 10 ring tones are available. y Alarm Clock: Select an alert tone for the alarm clock. 10 alert tones are available. y SMS Alert: Select a message tone. 5 message tones are available. y Key Tone: Select a keypad tone. Select Off to deactivate the keypad tone.
Note: y If you enter wrong PIN codes three times consecutively, the FWT prompts you to enter the correct PUK code. If you enter wrong PUK code several times, consult your service provider for the correct PUK code. y If you enter wrong PUK codes 10 times consecutively, the UIM card is invalidated. Contact your service provider to retrieve a new card. If the PIN code is activated, you have to enter the PIN code every time you power on the (OK). FWT.
9 FM Radio (Optional) Switching the Radio On/Off Switching the Radio On 1. 2. In the standby mode, select Menu > FM Radio. The FWT displays "Radio On!". The radio is switched on and the broadcasting screen is displayed. Select a channel to listen to the radio broadcast. Note: y The coiled cord connected the main unit and handset functions as the radio antenna.
Manual Tuning 1. In the standby mode, select Menu > FM Radio. 2. (Options) and select Manual Tuning. You can tune the radio channel Press manually. The FWT searches for an available channel. Press the Up/Down key to switch a channel. 3. 4. 5. (Set) to add the channel to the channel list or press Press tuning and return to the broadcasting screen. (Back) to stop Inching Tuning 1. In the standby mode, select Menu > FM Radio. 2. 3. Press (Options) and select Inching Tuning.
3. (OK) to complete the settings. Press If you set the frequency of the selected channel, the FWT prompts "Replace existing channel?" Press (Yes) to replace. Press (No) to re-select. Deleting a Channel 1. In the standby mode, select Menu > FM Radio. 2. 3. (Options) and select Delete Channel. Press Press the Up/Down key to scroll up or down the channel list. 4. Press (Delete) to delete a non-empty channel. 5. Press (Yes) to delete; press (No) to cancel.
10 Fun & Utility Alarm Clock After the alarm clock is activated, it rings at the specified time when your FWT is powered on. You can set up to five alarm clocks. 1. 2. Select Menu > Fun&Utility > Alarm. Press the Up/Down key to scroll up or down the alarm clocks. 3. 4. (Select) to select an alarm clock. Press Select Alarm On to startup the alarm clock. (OK). 5. Enter the time and press 6. Select: y Once: The alarm clock rings only once. y Everyday: The alarm clock rings once every day.
11 Menu Commands Phone Book See "Phone Book" on page 24. Messages See "Messages" on page 19. Call History Missed Calls z Press the Up/Down key to scroll up or down the records (up to 20). z Press to dial a record. You can save, delete or send a message to a record. Received Calls Dialed Calls Call Duration z z z Delete All The FWT records the duration of the last call, dialed calls, received calls, and all calls. You can view or reset the duration.
Stopwatch The FWT provides the stopwatch function, which can record up to 9 hours 59 minutes 59 seconds and 990 milliseconds. World Clock You can view the Greenwich Mean Time (GMT), current time of other 31 major time zones around the world, and local time. Line Game For details, see Help in your FWT. Smash Game For details, see Help in your FWT. Profiles See "Profile Settings" on page 26. Settings Display You can set backlight, contrast, date format, time format, and banner.
12 Maintenance and Troubleshooting Maintenance 1. 2. 3. 4. Place the FWT in a clean and dry environment. The temperature of the place should be no higher than +55°C or lower than –10°C. If the FWT is covered with dust, clean it with fine clean cloth. Do not clean it with cleanser or other chemical solvents. If the FWT does not operate normally due to a failed spare battery, replace the spare battery in time or use the power adapter to supply the FWT with power.
2. 3. 4. If the problem persists. Make sure that the antenna is installed properly. Adjust the antenna direction or move the FWT to a place covered where the signal is better. If the problem persists, contact your service provider to check whether the FWT is within the signal coverage area. After the FWT is powered off, there is no display sometimes while sometimes there is power supply icon and blinking battery icon. No information on the display screen is a normal status of FWT after power-off.
13 Specifications Item Dimensions (W × D × H) Description 210 mm × 183 mm × 81 mm Weight Less than 700 g Placement mode Horizontal or wall mounting Input voltage Linear power supply AC: 190 V – 300 V DC: 12 V Switch power supply AC: 90 V – 264 V DC: 12 V Spare battery Type: NiMH Capacity: 3.6 V 1000 mAh 3.6 V 1500 mAh (Optional) Maximum transmitter power ≥ 23 dBm Typical conversation power consumption 1.
