Wonderful Communication, Mobile Life. Welcome to HUAWEI ETS2028/2228/2528 Fixed Wireless Terminal.
Copyright © 2006 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this manual are the property of their respective holders. Notice The information in this manual is subject to change without notice.
Table of Contents 1 Warnings and Precautions .....................................................................................................1 2 Introduction ...........................................................................................................................7 Packing List ...................................................................................................................7 Appearance of the FWT ........................................................................
Deleting a Contact .......................................................................................................31 Copying a Contact .......................................................................................................31 Groups..........................................................................................................................32 Memory Status.............................................................................................................
1 Warnings and Precautions Before using HUAWEI Fixed Wireless Terminal (hereinafter referred to as FWT), read the following cautions and let your children know these, so that you can use your FWT correctly and safely. Basic Cautions According to the packing list, check items in the package box to make sure that they are complete and undamaged. Before installing and using FWT, read the user manual carefully.
y y Switch off your FWT near medial devices. Observe any instructions wherever the use of wireless device is prohibited. Traffic Safety y y Do not use your FWT while driving. Secure the FWT on its holder. Do not place the FWT on the seat or other places where it can get loose in a sudden stop or collision. Observe the rules and regulations of airline companies. Switch off your FWT before boarding an aircraft.
y y y y y y y y y y Before cleaning FWT, please turn off the FWT, and then disconnect the power supply and take out the battery. Before moving FWT, please disconnect the external power supply. Do not subject your FWT, battery, and power adapter to serious collision or shock. Otherwise, battery leakage, FWT malfunction, overheats, fire, or explosion may result. Do not place sharp metal objects such as pins near the earpiece.
y The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons. Emergency Call You can use your FWT for emergency calls. However, connections in all conditions cannot be guaranteed. You should never rely solely on the FWT for essential communications. Battery y y y y y y y y y y 4 If the battery fluid gets into eyes, do not rub them. Wash with clean water and seek medical assistance immediately.
Power Adapter y y y y y y y y y Use AC power as specified for the power adapter. Any violation of this rule may result in fire or malfunction of the power adapter. Do not short-circuit the power adapter. Short-circuiting the power adapter may cause fire or malfunction of the power adapter. Remove the dust on the power plug regularly. Do not use worn-out power cords. Otherwise, electric shock, short-circuiting of the power adapter, or fire may result.
Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons.
2 Introduction Packing List The FWT package box contains the following items. If any of the items is lost or damaged, contact your local dealer.
Appearance of the FWT Front View No. Item Description 1 antenna To receive signals. 2 Display screen To display information. 3 Left soft key z z z 8 In the standby mode, press it to access the main menu. In the non-standby mode, press it to perform the operation displayed on the lower left corner of the screen. Press this key to answer a call.
No. 4 Item Scroll key z z z z 5 Right key soft z z 6 OK key z z 7 End key z z z Description Up key: In the standby mode, press it to access the Calendar screen; during a call, press it to increase the volume. Down key: In the standby mode, press it to enable the radio (or alarm clock); during a call, press it to decrease the volume. Left key: In the standby mode, press it to view the call records. Right key: In the standby mode, press it to access the Write message screen.
No. 8 Item HANDFRE E key z z z 9 Call/Redial key z z Description In the standby mode, press it to make or answer a call without lifting the handset. When dialing a number, press it to cancel the dialing. During a call, press it to end the current call. Press it to make or answer a call. In the standby mode, press it to view the call history. In the standby mode, press and hold it to lock the FWT. z Press it to switch between input methods and so on.
Back View No . 1 Item Antenna Description To receive signals. 2 Hook To fix the FWT when installed vertically. 3 UIM case slot To house the UIM card 4 Battery case To house the spare battery. 5 Spare battery To supply the FWT with power. 6 Battery cord jack To connect to the battery cord. 7 Coiled cord jack on the Main unit To connect to the handset coiled cord. 8 Coiled cord To connect to the handset to the Main unit.
No . Item Description 10 Handset To make a call or answer a call by lifting it. 11 Antenna jack To connect to the antenna 12 DB9 serial port To maintain the FWT through it. 13 Power jack To connect to the power adapter for power supply. Icons Icon Description Indicates the signal strength. The more the bars, the stronger the signal strength. Indicates there is a new message. Indicates there is a new voice message. Indicates there is an outgoing call or an ongoing call.
13
3 Installation Installing the UIM Card (Optional) Caution: y y Consult your service provider to decide whether to use a user identity module (UIM) card. The UIM card and its golden contact can be easily damaged by a scratch or bend. Be careful when installing or removing the UIM card. Press and hold to power your FWT off and then disconnect it from the power socket. Install the UIM card according to the following figure. Make sure that the golden contact of the UIM card is facing downwards.
y y y If the FWT is connected to the power adapter and the spare battery is inserted, the FWT is powered by the power adapter, and meanwhile, the spare battery is charged. Charge the spare battery for at least eight hours for the first time. If a fully-charged spare battery is left unused for a long time, charge it for at least five minutes before using it again.
Removing the Spare Battery Press and hold to power off your FWT and then disconnect the FWT from the power socket. Then remove the battery house cover. Disconnect the battery cord and take out the spare battery. Installing the Antenna Power off your FWT and disconnect the FWT from the power socket. Then connect the antenna to the antenna jack on the Main unit. Make sure that the antenna is stably connected to the antenna jack.
Checking the Signal Strength 1. After installing the antenna, press and hold to power on your FWT. Wait until the signal strength icon appears or you can hear the dialing tone when you lift the handset. 2. If the signal strength icon does not appear after five minutes or you hear the failure tone when you lift the handset, it indicates that the FWT is not receiving signals. In this case, you need to adjust the direction of the antenna until you can hear the dialing tone on lifting the handset. 3.
2. According to the distance between the two hooks (7.7 cm), hammer two nails into the wall with 3 mm end left out. 7.7cm 3. Snap the hooks to the nails. Validating After installing the FWT, you can make a call to check whether it is correctly installed. 1. 2. 3. 18 Press and hold to power on your FWT. After connecting the FWT to the power socket, the icon appears, indicating that the FWT is powered normally. Lift the handset. In the standby mode, the signal strength appears normally.
4 Basic Operations Powering the FWT On or Off When the FWT is powered off, press and hold on. In the standby mode, press and hold to power it to power it off. Making a Call Making a Call Through the Keypad 1. 2. 3. In the standby mode, press number keys to enter a phone . number. If the entered phone number is wrong, press Press to dial the phone number. Press to end the call or cancel the dialing. Making a Call from the Dialed Calls List 1. 2. 3.
function for contacts saved in the FWT. Select Menu > Phone Book > Speed Dial. Press the Up/Down key to scroll up or down the items. If a number key is not assigned to a contact, press to select a contact from the phone book. If a number key is assigned to a contact, press for the following options: Change: Change a contact. Delete: Delete the contact. 1. 2. 3. 4. y y Answering a Call In the standby mode, you can lift the handset, press to answer a call.
y y y y Phone Book: Access the Phone Book screen. Messages: Access the Messages screen. Third Party Call: The function is network dependent. For details, consult your service provider. Voice Privacy: The function is network dependent. For details, see "Voice Privacy" on page 34. Locking the Keypad Even when the keypad is locked, you can lift the handset, press or press to answer a call. Locking the Keypad Manually Press and hold the # key for two seconds to lock the keypad.
5 Text Entry Text Input Mode While entering text, you can press the # key to change the input mode. The following table lists the input modes and their indicators. Indicator Text Input Mode eZiEn Smart English ABC English upper case abc English lower case 123 Numbers Note: In the edit mode, press once to delete the letter on for over two the left of the cursor. Press and hold seconds to delete all letters.
2. 3. Press the Up/Down key or the * key to select the word. Press the right key to confirm your selection. The word is displayed in the input area. Alternatively, press the 0 key to confirm your selection and enter a space behind the word. Note: y y y y y After you enter several letters, the FWT can give other letters to make out the candidate words. Press the Up/Down key or the * key to scroll the words and press the right key to confirm; or press number keys to enter letters.
y y In the "ABC" or "abc" input mode, press the number key repeatedly until the desired digit appears on the screen. In the "eZiEn" input mode, press the number key and then press the Up/Down key until the desired digit appears on the display screen. Entering Symbols 1. 2. 3. 24 In any input mode, press the * key to display the symbol list. Press the Up/Down key to scroll up or down the symbol list. Press the corresponding number key to enter a symbol.
6 Messages Writing and Sending a Message Select Menu > Messages > Write Message. Write the message. You can enter up to 160 English letters. for the When writing the message, you can press following operations: y Insert Template: Insert a commonly used phrase. y Insert Phone Number: Insert a contact number from the phone book. 3. After writing the message, press for the following operations: y Send: Send the message. y Send&Save: Send the message and save it to the outbox.
appears on the display screen. If the icon blinks, it indicates that the message memory is full. Do the following to view the inbox: 1. 2. 3. 4. Select Menu > Messages > Inbox. Press the Up/Down key to scroll up or down the messages. Press (View) to view the message. Press (Options) to select Reply, Delete, Forward, Call or Save Number. Viewing the Outbox and the Draft The outbox stores messages that are sent successfully. You can delete, forward or re-send a message in the outbox.
2. Select Call Voice Mail Center and press call the voice mail center. (Select) to Setting or Viewing the Voice Mail Number 1. 2. Select Menu > Messages > Voice Mail > Voice Mail Number. If the voice mail number is already set, you can view and edit (OK). it; if not, enter the voice mail number and press Note: The voice mail function is network dependent. You must subscribe for the service. For the voice mail number and other information, consult your service provider.
contacts saved in the FWT to a message group. Select Menu > Messages > Message Settings > Group Settings. Press the Up/Down key to scroll up or down the message groups. Press (Options) to select View, Add, Rename or Delete All. 1. 2. 3. Setting the Auto Save Function Select Menu > Messages > Message Settings > Auto Save to set the auto save function. You can select: y y Send And Save: Activate the auto save function. Messages are automatically saved after being sent.
The priority function is network dependent. For details, consult your service provider. Setting the Delivery Ack Select Menu > Messages > Message Settings > Delivery Ack. You can set whether to receive a delivery report after a message is sent. Setting the Memory Status Select Menu > Messages > Message Settings > Memory Status to view the memory status.
7 Phone Book Adding a Contact A contact is saved to the memory in use. 1. 2. 3. y y 4. 5. Select Menu > Phone Book > Add New. Enter the name and press (OK). Set other options: If the memory in use is the FWT, you can set: Name, General Number, Home Number, Office Number, and Memo (you need to set at least one phone number). If the memory in use is the UIM card, you can set General Number only. Press (OK) to save the settings and press the Up/Down key to set other items.
Editing a Contact 1. 2. 3. Select Menu > Phone Book > Search to search for the contact to edit. Press (Options) and select Edit. Press (Save) to save the contact or press (Back) to cancel. Deleting a Contact Delete a Contact 1. 2. 3. Select Menu > Phone Book > Search to search for a contact to delete. Press (Options) and select Delete. Press (Yes) to delete the contact or press (No) to cancel. Delete All Contacts 1. 2. 3. Select Menu > Phone Book > Delete All.
2. 3. Press (Options) and select Copy To UIM or Copy To Phone. If the contact is saved in UIM card, select Copy To Phone to copy it to the FWT. If the contact is saved in FWT, select Copy To UIM to copy it to the UIM card. Press (Yes) to copy the contact or press (No) to cancel. Copying All Contacts Select Menu > Phone Book > Copy All. Select UIM To Phone or Phone To UIM. y If you select UIM To Phone, all contacts are copied to the FWT.
Viewing the Memory Status Select Menu > Phone Book > Memory Status to view the memory status. Saving My FWT Number 1. 2. 3. Select Menu > Phone Book > My Phone Num. Press (Edit) to edit the FWT number. Press (OK) to save the FWT number.
8 Settings Call Settings Minute Alert If the minute alert function is activated, your FWT notifies you of the call duration by giving an alert 10 seconds before the end of each minute. 1. 2. y y Select Menu > Settings > Call Settings > Minute Alert. Select one of the following options: On: Activate the minute alert function. Off: Deactivate the minute alert function. Voice Privacy The voice privacy function can protect your conversion from interception. The voice privacy function is network dependent.
1. 2. Select Menu > Settings > Call Settings >Auto Dial. Select one of the following options: “Off”, “After 3 Seconds”, “After 4 Seconds”, “After 5 Seconds”, After 6 Seconds”, “After 7 Seconds”, “After 8 Seconds” and “After 9 Seconds”. Shortcut Key Settings The FWT provides shortcut keys for your convenience. Note: In the standby mode, the default shortcut key settings are shown as follows: y y y y 1. 2. y Up key: press it to access the Calendar screen; during a call, press it to increase the volume.
customize a profile. Selecting a Profile 1. 2. 3. In the standby mode, select Menu > Profiles. Press the Up/Down key to scroll up or down the profiles: General, Outdoor, and Quiet. Press (Select) and select Set to activate the profile. Note: In the standby mode, press and hold the * key to activate the quiet mode. Press and hold the * key again to restore the FWT to the previous mode. Editing a Profile 1. 2. 3. y y y y y y 36 In the standby mode, select Menu > Profiles.
Security Settings Note: The emergency call function of the FWT is not affected by the operation of FWT lock function. Setting the FWT Lock The FWT lock protects your FWT from unauthorized usage. If necessary, you can activate the FWT lock. You can change the default FWT lock code (000000) into a numeric string of 4 to 8 digits. Remember the FWT code. In case you forget it, contact your service provider. If the FWT lock activated, you have to enter the FWT code every time you power on the FWT.
Note: y y If you enter wrong PIN codes three times consecutively, the FWT prompts you to enter the correct PUK code. If you enter wrong PUK code several times, consult your service provider for the correct PUK code. If you enter wrong PUK codes 10 times consecutively, the UIM card is invalidated. Contact your service provider to retrieve a new card. If the PIN code is activated, you have to enter the PIN code every time you power on the FWT. Enter the correct PIN code (OK).
carrier. The supplementary services need special commission. This section only introduces some typical supplementary services. Caller ID display: When there is an incoming call, the FWT displays the phone number of the caller on the screen. y Three way calling: Three parties can hold a conversation at the same time. y Call forwarding: The incoming calls are forwarded to the specified phone accordingly to facilitate you to answer. Supplementary services are network dependent.
9 FM Radio(Optional) Switching the Radio On/Off Switching the Radio On 1. 2. In the standby mode, select Menu > FM Radio. The FWT displays "Radio On!". The radio is switched on and the broadcasting screen is displayed. Select a channel to listen to the radio broadcast. Switching the Radio Off 1. 2. 3. In the standby mode, select Menu > FM Radio. Press (Options) and select Switch Off. Press (Select) to switch the radio off and return to the home screen. Searching for a Channel Auto Tuning 1. 2. 3.
2. 3. 4. 5. Press (Options) and select Manual Tuning. You can tune the radio channel manually. The FWT searches for an available channel. Press the Up/Down key to switch a channel. Press (Set) to add the channel to the channel list or (Back) to stop tuning and return to the press broadcasting screen. Inching Tuning 1. 2. 3. 4. In the standby mode, select Menu > FM Radio. Press (Options) and select Inching Tuning. Press the Up/Down key and the FWT searches for all available channels between 87.
Adding a Channel 1. 2. 3. After searching for or set a frequency, press (Options) and select Save Channel. Press the Up/Down key to scroll up or down the channel list. Press (OK) to complete the settings. If you set the frequency of the selected channel, the FWT (Yes) to prompts "Replace existing channel?" Press (No) to re-select. replace. Press Deleting a Channel 1. 2. 3. 4. 5. 42 In the standby mode, select Menu > FM Radio. Press (Options) and select Delete Channel.
10 Fun & Utility Alarm Clock After the alarm clock is activated, it rings at the specified time when your FWT is powered on. You can set up to five alarm clocks. 1. 2. 3. 4. 5. 6. y y y Select Menu > Fun&Utility > Alarm. Press the Up/Down key to scroll up or down the alarm clocks. Press (Select) to select an alarm clock. Select Alarm On to startup the alarm clock. Enter the time and press (OK). Select: Once: The alarm clock rings only once. Everyday: The alarm clock rings once every day.
2. 44 Press (Options) to select: Add Schedule, View Current Month, View All, Delete All, Delete Passed, Memory Status and Go To Date.
11 Menu Commands Phone Book See "Phone Book" on page 30. Messages See "Messages" on page 25. Call History Missed Calls Received Calls Dialed Calls Call Duration Delete All 45 Press the Up/Down key to scroll up or down the records (up to 20). z Press to dial a record. z You can save, delete or send a message to a record. z The FWT records the duration of the last call, dialed calls, received calls, and all calls. You can view or reset the duration.
Fun & Utility Alarm See "Alarm Clock" on page 43. Schedule See "Schedule" on page 43. Calculator You can use the calculator for basic calculations. Press the # key to enter the decimal point. Press the * key to select operators such as add, subtract, to multiply and divide. Press display the results. Stopwatch The FWT provides the stopwatch function, which can record up to 9 hours 59 minutes 59 seconds and 990 milliseconds.
Settings Display You can set backlight, contrast, date format, time format, and banner. You can set the backlight to off, always on, or ff if there is no operation on the FWT for 10 seconds, 20 seconds or 30 seconds. You can press the left/right key to increase or decrease the contrast. You can set the date format to yyyy-mm-dd, dd-mm-yyyy or mm-dd-yyyy. You can set the time format to 12-hour or 24-hour. You can activate or deactivate the banner. Call Settings See "Call Settings" on page 34.
12 Maintenance and Troubleshooting Maintenance 1. 2. 3. 4. Place the FWT in a clean and dry environment. The temperature of the place should be no higher than 55°C or lower than -10°C. If the FWT is covered with dust, please clean it with fine clean cloth. Do not clean it with cleanser or other chemical solvents. If the FWT does not operate normally due to a failed spare battery, please replace the spare battery in time or use the power adapter to supply the FWT with power.
2. The external voltage of the power adapter is low or unstable; disrupting the normal functioning of the FWT. Check whether the external voltage of the power adapter is normal. You can also install the spare battery in the FWT. There is no signal icon on the display screen. 1. Make sure that the antenna is installed properly. 2. If still there is no signal, contact your service provider to check whether the FWT is in the signal coverage area. Time is not displayed. 1.
There is only the battery icon on the display screen. It indicates that the FWT is powered by the spare battery. If the FWT is powered solely by the spare battery and the battery icon is blinking without any bar inside, it indicates that the battery level is low. Use the power adapter to charge the battery or replace the spare battery.
13 Specifications Item Description Dimensions (W × D × H) 214 mm × 156 mm × 77 mm Weight Less than 700 g Placement mode Horizontal or wall mounting Input voltage Switch power supply AC: 90 V–264 V DC: 12 V Spare battery Type: NiMH Capacity: 3.6 V 1000 mAh 3.6 V 1500 mAh (Optional) Maximum transmitter power ≥23 dBm Typical conversation power consumption 1.
