Copyright © 2009 Huawei Technologies Co., Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions Ltd. and other Huawei trademarks are trademarks of Huawei Technologies Co., All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The information in this document is subject to change without notice.
Table of Contents Getting to Know the EM775............................................................. 1 Requirements for the PC ................................................................. 2 Preparing the EM775 ...................................................................... 3 Installation Guide .......................................................................... 4 Safety Information........................................................................
Thank you for purchasing Huawei EM775 HSPA Module. Note: This manual briefly describes the preparation, the process for installing/uninstalling, and safety precautions for using Huawei EM775 HSPA Module (hereinafter referred to as the EM775). You are recommended to read the manual before using the EM775. The signal strength and the transmission rate are affected by the actual environment. Getting to Know the EM775 The following figure shows the appearance of the EM775.
Screw holes They are used to fix the EM775 on the main board of the PC with screws. Antenna interfaces They are used to connect antennas. EM775 has an external antenna which connect with laptop. The max gain which is allowed of external antenna is ： 900M<2.1dBi 850M<4.28dBi 1900M<3.6dBi 1800M<3.6dBi 2100M<4.3dBi Requirements for the PC To use the EM775, the PC must meet the following requirements: WWAN Mini PCI Express interface. Windows 2000 SP4, Windows XP SP2, Windows Vista and Linux 2.6.
Preparing the EM775 Locate the WWAN Mini PCI Express interface on the main board of the PC. Find the main antenna and the auxiliary antenna. If a USIM/SIM card is provided by your service provider, insert the USIM/SIM card into the USIM/SIM card slot on the main board of the PC. Note: In certain cases, your PC may be disassembled only by the professionals. Before you install the EM775 onto the main board of the PC, consult the PC manufacturer or read the user manual of the PC.
Installation Guide Installing the EM775 onto the Main Board of the PC 1. Insert the Mini PCI Express connector of the EM775 into the WWAN Mini PCI Express interface on the main board of the PC. 2. Press downwards to fix the EM775 in the module slot.
3. Use a screwdriver to fix the EM775 onto the main board of the PC with two screws provided in the EM775 packing box. 4. Insert the connector of the main antenna into the MAIN antenna interface (M) of the EM775 according to the indication on the label of the EM775. Insert the connector of the auxiliary antenna into the AUX antenna interface (A) of the EM775 in the same way. Note: Insert the antenna connectors vertically into the antenna interfaces of the EM775.
Do not pinch the antenna cable or damage the connectors. Otherwise, the wireless performance of the EM775 may be reduced or the EM775 cannot work normally. Ensure that the antenna cables are routed through the channel in the frame of the PC and do not lay across the raised edges of the frame.
Removing the EM775 from the Main Board of the PC 1. Disconnect the antenna cables from the EM775. You can lift the connectors with a small screwdriver. 2. Remove the two screws with the screwdriver.
3. Slide backwards the two clips to release the EM775 from the slot. Then, lift up the EM775. Installing the EM775 Software A disk is provided in the EM775 packing box. The disk contains the management program and the driver of the EM775. 1. Insert the disk into the disk drive of the PC. 2. Find the AutoRun.exe file under the disk path. Then double-click AutoRun.exe to run the program. 3. Follow the prompts of the installation wizard. 4.
Note: It is recommended to restart the PC after the uninstallation to ensure that the management program is completely uninstalled.
Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device. Interference Do not use your wireless device if using the device is prohibited or when it causes danger or interference with electric devices. Medical Device Do not use your wireless device and follow the rules and regulations set forth by the hospitals and health care facilities. Some wireless devices may affect the performance of the hearing aids.
granule, dust, or metal powder) Area indicated with the "Explosives" sign Area indicated with the "Power off bi-direction wireless equipment" sign Area where you are generally suggested to stop the engine of a vehicle Traffic Security Observe local laws and regulations while using the wireless device. To prevent accidents, do not use your wireless device while driving. RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer.
WEEE Approval The wireless device is in compliance with the essential requirements and other relevant provisions of the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE Directive). RoHS Approval The wireless device is in compliance with the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive 2002/95/EC (RoHS Directive). Laws and Regulations Observance Observe laws and regulations when using your wireless device.
considerably low or high temperature. Use only accessories of the wireless device approved by the manufacture. Contact the authorized service center for any abnormity of the wireless device or accessories. Do not dismantle the wireless device or accessories. Otherwise, the wireless device and accessories are not covered by the warranty. Emergency Call This wireless device functions through receiving and transmitting radio signals. Therefore, the connection cannot be guaranteed in all conditions.
may cause undesired operation. Warning: Changes or modifications made to this equipment not expressly approved by HUAWEI may void the FCC authorization to operate this equipment.
