Product name Confidentiality level HUAWEI UMTS M2M Module Confidential Product version V100R001 Total 95 pages HUAWEI UMTS M2M Module AT Command Interface Specification Prepared by Xu qifeng、Pei na、Ma zhaoyang Date Reviewed by Date Approved by Date Authorized by Date 2009-02-03 Huawei Technologies Co., Ltd. All rights reserved (REP01T01 V2.31/ IPD-CMM V2.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Revision Record Date Revisio n version CR ID / defect ID Section numbe r Change description Author 2008-10-22 0.10 AT command interface draft Yuan kangqiang completed initially 2009-02-03 0.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Table of Contents HUAWEI UMTS M2M Module AT Command Interface Specification........................................... 1 Table of Contents ............................................................................................................................. 3 Table List......................................................................................................................................... 10 Figure List .........
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.10.1 Command Syntax................................................................................................... 21 3.10.2 Description ............................................................................................................. 21 3.10.3 Defined Value......................................................................................................... 21 3.10.4 Informative Examples...........................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 4 SMS Interface Description.......................................................................................................... 29 4.1 Select the SMS type +CSMS.............................................................................................. 29 4.1.1 Command Syntax..................................................................................................... 29 4.1.2 Description ................................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 4.14.1 Command Syntax................................................................................................... 49 4.14.2 Interface Description .............................................................................................. 49 4.14.3 Defined Values ....................................................................................................... 49 4.15 Message list command +CMGL ...........................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 6.5.2 Description ............................................................................................................... 60 6.5.3 Defined Values ......................................................................................................... 60 6.6 System configuration reference setting %SYSCFG ........................................................... 61 6.6.1 Command Syntax..........................................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 9.3 Show PDP address +CGPADDR ....................................................................................... 76 9.3.1 Command Syntax..................................................................................................... 76 9.3.2 Description ............................................................................................................... 76 9.3.3 Defined values........................................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 11.3 Technology Limitations ..................................................................................................... 86 12 Software Quality Attributes ...................................................................................................... 86 13 Dependencies ............................................................................................................................ 86 14 Feasibility Analysis .
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Table List Table 1 Influence of V parameter on the response format ...................................................... 18 Table 2 Bit number ..................................................................................................................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Figure List Figure 1 Block diagram of interaction between TE and MS.................................................... 14 Figure 2 Half byte coding with a total of 5 digits .....................................................................
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential HUAWEI UMTS M2M Module AT Command Interface Specification Keywords: UMTS, Module, WCDMA, GPRS, GSM Abstract: This Document describes the AT command-based communication interface between TE and MS of Huawei UMTS Module. The interface can implement the functions such as voice call, SMS, telephone service, supplementary service, TCP, UDP and network setting.
HUAWEI UMTS M2M Module AT Command Interface Specification All rights reserved Confidential Page 13, Total 96
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 1 Scope This document describes the AT interface of Huawei UMTS Module. The description on the AT interface is only limited to the interface packet itself, the usage and use procedure of TE and MS, and does not cover the contents which are not directly related to the interface. Note: Reinforced insulation or double insulation must be provided to isolate DC source from AC mains supply. 1.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential at the end). For the “response” message or URC reported by the board, the maximum length is limited to 1600 characters. 3) Each command line can include only one AT command. For the URC instruction or response reported from MS to TE, only one AT command is allowed in a command line.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential All interfaces herein refer to the interfaces between TE and MS, and are used for guiding the implementation of the function requirements. The interface covers voice call, short message receiving and sending, data traffic flow, phone book statistics, supplementary service, and MS network system information setting. For the commands sent from TE to MS, see also the detailed description in Appendix 16.1.
HUAWEI UMTS M2M Module AT Command Interface Specification Command Confidential Possible response(s) E[] OK 3.2.2 Description This command is used to set whether MS will echo the characters received from TE. 3.2.3 Defined Values : 0 MS does not echo the characters received from TE. 1 MS echoes the characters received from TE. If no is included, it is equivalent to the effect that the is 0. Note: Software may set ATE0 automatically. 3.
HUAWEI UMTS M2M Module AT Command Interface Specification S4? Confidential OK 3.4.2 Description This command is used to set the response format character S4. S4 saves the response format character in the form of ASCII code value. This character is sent by MS, and serves as a part of the header, tail and end mark of the “result code” and “information response”.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.6 Backspace character S5 3.6.1 Command Syntax Command Possible response(s) S5= OK S5? OK 3.6.2 Description This command is used to set the backspace character S5. S5 saves the backspace character in the form of ASCII code value. This character is sent by TE, and means to delete the previous character. It is identified by MS. 3.6.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.8.1 Command Syntax Command +CSQLVL +CSQLVL=? Possible response(s) , +CSQLVL: ,OK 3.8.2 Interface Description This command is used to periodically reset the module automatically. 3.8.3 Defined Values < uiPercent >: The grid of the signal. 0~5: Indicate the signal intensity.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.9.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential The EXECUTION command returns the software version number of ME. 3.11.3 Defined Value : Software version number. It is a string composed of 31 characters at most. 3.12 IMSI query command +CIMI 3.12.1 Command Syntax Command Possible response(s) +CIMI OK +CIMI=? OK 3.12.2 Interface Description This command queries the IMSI value of the USIM card or SIM card. 3.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential This command is used to query the IMEI of board. 3.13.3 Defined Value : The IMEI value of the board is returned directly. The returned value is a string composed of: 8 char 6 char TAC SNR TAC Type code allocated for device SNR Sequence number of the device Spare For standby purpose 1 char Spare 3.13.4 Informative Examples If TAC is “35154800”, SNR is “022544”, and Spare is “4”, then AT+CGSN 351548000225444 3.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential : Coding scheme. It means the character code of the spn_name field, and specifies the language. 0 GSM 7 bit Default Alphabet 1 RAW mode (namely, upload the spn_name in the format of original data). : A string. In case of GSM7bit code, the string is composed of 16 characters at most.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.16.2 Interface Description The SET command is used to set mode value to open or close unsolicited reports. The unsolicited reports it can control are listed below: %DSFLOWRPT, %RSSI, %MODE, %SIMST, %SRVST, %MODE, %EARST, %SMMEMFULL. The unsolicited reports are closed if the mode value is set to 0 and the unsolicited reports are open if the mode value is set to 1. The default value of mode is set to 0.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.18 Network information query %NWINFO 3.18.1 Command Syntax Command %NWINFO Possible response(s) %NWINFO: ,< srv_nodeB_PLMN >, < srv_nodeB_BS >,,,,,,,,, OK 3.18.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.19 Temperature of PA and source voltage query %CONINFO 3.19.1 Command Syntax Command %CONINFO Possible response(s) %CONINFO:,OK 3.19.2 Interface Description This command is used to query PA temperature of the module high frequency and external source voltage. To acquire module state by user for convenience, and help to consider if it has to be protected for safety. 3.19.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 3.21 Module delay resetting %RESET 3.21.1 Command Syntax Command Possible response(s) %RESET= OK %RESET: OK %RESET:(range of supported )OK %RESET? %RESET=? 3.21.2 Interface Description This command is used to delay to reset module by user. 3.21.3 Defined Values : Delay time.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential NOTE: If MT does not support time zone information then the three last characters of
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential +CMGF[=] OK +CMGF? +CMGF: OK +CMGF=? +CMGF: (list of supported s)OK 4.2.2 Description The SET command is used to set the format of the short message. The format has two modes, and depends on the parameter. The two modes are: PDU mode and text mode.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 4.4 Indication of new message reported directly +CMT 4.4.1 Command Syntax Command Possible response(s) +CMT: [], 4.4.2 Description Received new messages are not stored, but reported to TE directly. 4.4.3 Defined Values : Reserved. : Integer value, which indicates the number of bytes of PDU data. : Protocol data unit.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 4.6.2 Description Received new messages are not stored, but reported to TE directly. 4.6.3 Defined Values : Integer value, which indicates the number of bytes of PDU data. : Protocol data unit. The data structure is as follows: [] TPDU Where, the , , , and fields are defined in the same way as in the section “Message sending command”.
HUAWEI UMTS M2M Module AT Command Interface Specification Command Confidential Possible response(s) +CNMI=[[,< mt>[,[,[, OK ]]]]] +CMS ERROR: +CNMI? +CNMI: ,,,,OK +CNMI=? +CNMI: (list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s) OK In case of SMS-related error: 4.7.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 2 If SMS-DELIVER is stored into MS, indication of the memory location is routed to the TE. +CMTI: , 3 If SMS-DELIVER is stored into MS, SMS-DELIVER indication is not routed to TE. In the above three modes, the interaction between TE and MS is shown in the following diagram.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Note: The class of message is given by the TP-DCS domain of the message. For details, see the DCS parameter description of the “+CMGS” command. +CMT & +CNMA means requiring TE to send a confirmation (+CNMA). : For use of setting the cell broadcast information. It is not supported currently. : For use of setting the message acknowledgement. 0 Do not send message acknowledgement to the TE.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential parameter is present and not set to 0 then the ME shall ignore and follow the rules for shown below. If deleting fails, +CMS ERROR: is returned. TEST command returns the valid memory locations and the supported values of . The TEST command returns the storage position where the message is currently stored, and the supported values. 4.8.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential If ME does not get acknowledgement within required time (network timeout), ME should send RP-ERROR to network, and should shall automatically disable routing to TE by setting both and values of +CNMI to zero. To make the MS report the message notification again, you need to set and again.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 0,1 TP-UDL 0 to 159 TP-UD The 7th bit and bits 2~5 of the first byte are not used in SMS-DELIVER-REPORT, and the sender should set them to 0. If any bit of them is not 0, the receiver should ignore them. Description: : TP-message type. Bits 0 and 1 in the first byte.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential UCS2 code mode. When the user inputs 1 Chinese characters, the TE will select this 0 value. bit1~0 (message type, its value is selected by TE according to the user’s options) bit7~4 (while sending the message, the TE does not select this TP-DCS mode) bit3 Class 0, provided to the interface to display 0 and reply that the SC has received but not 0 stored it. 0 Class 1, stored to the MS (i.e.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Class 3, stored to the TE. When the MS 1 receives the message, but has not 1 transmitted it to the TE, it will give a response to the SC. : Number of bytes occupied by the “user data” domain. If the value is 0, the “User data” domain does not exist. : The “user data” domain may include “user data header”.
HUAWEI UMTS M2M Module AT Command Interface Specification Command +CPMS=[, [,]] Confidential Possible response(s) +CPMS: ,,,,,< CR>OK In case of MS-related error: +CME ERROR: +CPMS: ,,,,,, +CPMS? ,,OK< CR> In case of MS-related error: +CME ERROR: +CPMS=? +CPMS: (list of supported
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Integer value. It indicates the total number of messages currently stored in . : Integer value. It indicates the total number of messages currently stored in . 4.11 Reporting message storage media being full %SMMEMFULL 4.11.1 Command Syntax Command Possible response(s) %SMMEMFULL: 4.11.2 Description When the message storage media overflow, the event will be reported automatically. 4.11.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential sc_len has the value of 0 (for the PDU format, see the “+CMGS” command) in the PDU. 4.12.3 Defined Values : String value. It indicates the SMSC number. The number is composed “*”, “#” and “0”-“9”. The number contains 20 characters at most. : Integer value. It indicates the number type, where “145” means an international call.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential [] TPDU SMSC address. Its structure is as follows: . . Address-Length Type-of-Address 1 2 3 4 Addr. 5 ................................ Address-Value µ . . : Length of the SCA (short message service center number). It is composed of two characters. It indicates the number of characters occupied by and /2. : Number address type.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 0000 The number is determined by the numbering plan at the network side. 0001 ISDN/telephone numbering plan. 0011 Data numbering plan, not in use currently. 0100 Telex numbering plan, not in use currently. 1000 National numbering plan, not in use currently. 1001 Private numbering plan, not in use currently. 1010 ERMES numbering plan, not in use currently. : Address number. One byte contains two digits.
HUAWEI UMTS M2M Module AT Command Interface Specification 0 1 SMS-SUBMIT (in the direction MS to SC) 0 1 SMS-SUBMIT-REPORT (in the direction SC to MS) 1 1 Reserved Confidential : It indicates whether the SC needs to receive the short message that is still stored in the SC and has the MR and DA identical with those of the message sent previously from the same OA. The values are as follows: 0 To receive 1 Not to receive : It indicates the validity of the VP field and the format.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential If the values are 1 0 0 1 0, it indicates Email. Other values are not supported currently. : Coding mode of user data. The values are as follows: Bit7…bit4 Bit5 Bit3…..bit0 0: Message is not Bit1 bit0 indicate message type compressed 0 0 : Class 0, providing display and reply to the SC that the message is received but not stored. 1: Message is 1 : Class 1, stored to the NV (or SIM card if the compressed.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Bit2 Coding mode of message. The values are as follows: 0: GSM 7 bit default code 1: 8bit data Bit1 bit0 message type indication 0 0 : Class 0, providing display and reply to the SC that the message is received but not stored. 0 1 : Class 1, stored to the NV (or SIM card if the NV is full) 1 0 : Class 2, for use of SIM only. After the message is stored, the storage state will be replied to the SC.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential AT+CMGS=17(CR) >81000B813109010054F3001804534E4E3A \x1A Note: Data interpretation, 81(
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential : Storage state of the message. The values are as follows: (In the PDU mode, the default value is 0) 0 Unread message that has been received 1 Read message that has been received 2 Unsent message that has been stored 3 Sent message that has been stored 4 Any message (This value is only applicable to the “+CMGL” command) : Position number in the storage. The digits are decimal numbers that range from 0 to 9.
HUAWEI UMTS M2M Module AT Command Interface Specification 4 Confidential Any message : Integer value, which indicates the position in the storage. : Reserved. : Integer value, which indicates the number of bytes of TPDU data. : Protocol data unit. The data structure is as follows: [] TPDU Where, the , , , and fields are defined in the same way as in the section “Message sending command”.
HUAWEI UMTS M2M Module AT Command Interface Specification "REC READ" read SMS "STO UNSENT" stored and unsent SMS "STO SENT" stored and sent SMS "ALL" all SMS Confidential 4.16 Read a message +CMGR 4.16.1 Command Syntax Command Possible response(s) In case of pdu mode and successful execution of command: +CMGR= +CMGR: ,[],OK or: +CMS ERROR: +CMGR=? OK 4.16.
HUAWEI UMTS M2M Module AT Command Interface Specification Command Confidential Possible response(s) +CGSMS= OK +CGSMS? +CGSMS:OK +CGSMS=? +CGSMS: (list of s)OK supported 4.17.2 Description The SET command is used to set the message bearer domain, namely, selection of CS/PS domain. The READ command returns the current message bearer domain.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 1 keep enabled until the time between the response of the latest message send command (+CMGS, +CMSS, etc.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 5.2.1 Command Syntax Command Possible response(s) In case of =2 and successful execution of command: +CLCK: OK +CLCK=,[, In case of ≠2 and successful execution of [,]] command: OK In case of MS-related error: +CME ERROR: +CLCK=? +CLCK: (list of s)OK supported 5.2.
HUAWEI UMTS M2M Module AT Command Interface Specification Command Confidential Possible response(s) OK +CPIN=[,] In case of MS-related error: +CME ERROR: +CPIN? +CPIN: OK +CPIN=? OK 5.3.2 Description The READ command is used to indicate whether password input request exists. The SET command is used to check and unlock the PIN and PIN2.
HUAWEI UMTS M2M Module AT Command Interface Specification Command % SIMLOCK =? Confidential Possible response(s) % SIMLOCK:(0,2),"password(6~8)” OK 5.4.2 Interface Description This command is used to unlock simlock function and query if enable simlock or not. If user inputs wrong password three times continuously, module will be reset. 5.4.3 Defined Values : 0: Unlock simlock function. 2: Query simlock state.
HUAWEI UMTS M2M Module AT Command Interface Specification 1 Restricted service 2 Valid service 3 Restricted regional service. 4 Power-saving and deep sleep state Confidential : System service domain. The values are as follows: 0 No service. 1 Only CS service 2 Only PS service 3 PS+CS service 4 CS and PS not registered, searching : Roaming status. The values are as follows: 0 Non roaming state 1 Roaming state : System mode.
HUAWEI UMTS M2M Module AT Command Interface Specification Command Confidential Possible response(s) %SRVST: 6.2.2 Description When the service state changes, the MS will report the new service state to the TE. 6.2.3 Defined Values : System service state. The values are as follows: 0 No service. 1 Restricted service. 2 Valid service 3 Restricted regional service. 4 Power-saving and deep sleep state 6.3 SIM state change indication %SIMST 6.3.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential %MODE:[,] 6.4.2 Interface Description When the system mode or sub-mode changes, the MS will report this indication to the TE. 6.4.3 Defined Values : System mode. The values are as follows: 0 No service. 1 AMPS mode (not in use currently) 2 CDMA mode (not in use currently) 3 GSM/GPRS mode 4 HDR mode 5 WCDMA mode 6 GPS mode : System sub mode.
HUAWEI UMTS M2M Module AT Command Interface Specification 1 Confidential -111 dBm 2...30 -109... -53 dBm 31 Equal to or higher than -51 dBm 99 Unknown or unmeasurable. 6.6 System configuration reference setting %SYSCFG 6.6.1 Command Syntax Command Possible response(s) %SYSCFG= ,,,, OK/ERROR % SYSCFG? %SYSCFG:,,< band>,, OK %SYSCFG=? OK 6.6.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 00100000(CM_BAND_PREF_GSM_RGSM_900) Railway GSM 900 00200000(CM_BAND_PREF_GSM_PCS_1900) GSM PCS 00400000(CM_BAND_PREF_WCDMA_I_IMT_2000) WCDMA IMT 2000 00800000 (CM_BAND_PREF_WCDMA_II_PCS_1900) WCDMA_II_PCS_1900 04000000 (CM_BAND_PREF_WCDMA_V_850) WCDMA_V_850 Roaming support: 0 Not supported 1 Roaming is supported 2 No change domain setting: 0 CS_ONLY 1 PS_ONLY 2 CS_PS 3 ANY 4 No change 7 Phone
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential The READ command returns the currently selected phonebook memory. Optionally, the number of entries in use and the maximum number of entries should also be returned. The TEST command returns the supported phonebook memory types. 7.1.3 Defined Values : Phonebook memory type. Currently, only “SM”,”ON”,”EN” are supported.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 7.2.3 Defined values , : integer type values in the range of location numbers of phonebook memory : string type phone number of format : type of address octet in integer format (refer TS 24.008 [8] subclause 10.5.4.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 7.3.3 Defined values , , : integer type values in the range of location numbers of phonebook memory : string type phone number of format : type of address octet in integer format (refer TS 24.008 [8] subclause 10.5.4.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential : integer type values in the range of location numbers of phonebook memory : string type phone number of format : type of address octet in integer format (refer TS 24.008 [8] subclause 10.5.4.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential , , : Integer value. It indicates the position in the phonebook memory. The values of index1 and index2 are less than or equal to the “total” field returned by the “+CPBS?” command. : String type, telephone number. : Number type: “145” means an international call.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential maximum length of the “text” field, and maximum length of the “email” field. When storing the phonebook, all input lengths must fall within the maximum length range. 7.6.3 Defined Values : Integer value. It indicates the position in the phonebook memory. : String type, telephone number. (legal characters only include: ’0’ – ‘9’, ‘*’, ‘#’, ‘+’, ’(‘, ’)’, ’-‘.
HUAWEI UMTS M2M Module AT Command Interface Specification +COPS=? Confidential +COPS: [list of supported (,long alphanumeric ,short alphanumeric ,numeric [,< rat>])s][,,(list of supported s),(list of supported s)]OK In case of CME error: +CME ERROR: 8.1.2 Interface Description This interface enables to query the network state and network selection mode currently registered by the MS.
HUAWEI UMTS M2M Module AT Command Interface Specification 0 GSM 2 UTRAN Confidential 8.1.4 Examples of searching network I. To query the present status of ME's network registration using the test command: +COPS:(2,"","","46007",2),(3,"China Unicom","UNICOM","46001",0),(3,"China Mobile Com","CMCC","46000",0),,(0,1,3,4),(0,1,2) OK II. Automatic search of network AT+COPS=0 OK Note: in SET command, that mode equals to 0 makes other parameters invalid. III.
HUAWEI UMTS M2M Module AT Command Interface Specification +CREG=? Confidential +CREG: (list of s)OK supported 8.2.2 Interface Description The SET command is used to control “+CREG” to report event proactively.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 8.3.2 Interface Description The SET command is used to control “+CGREG” to report event proactively. When =1, and the state of network registration changes, the following will be reported: +CGREG:< stat > When =2, and the cell information changes, the following will be reported: +CGREG: [,,] The READ command returns the current registration state .
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential ratio> , , , [+CGEQNEG: , ,, ,, , , , , , , , […]] +CGEQNEG=? +CGEQNEG: (list of s associated wit
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential : a numeric parameter that (1,2,3,…) indicates the maximum allowed SDU size in octets : a string parameter that indicates the target value for the fraction of SDUs lost or detected as erroneous. SDU error ratio is defined only for conforming traffic. The value is specified as 'mEe'. As an example a target SDU error ratio of 5•10-3 would be specified as '5E3' (e.g. +CGEQNEG:…,”5E3”,…).
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential context activation procedures may take place prior to or during the PDP startup if they have not already been performed using the +CGATT and +CGACT commands. If context activation takes place during the PDP startup, one or more s may be specified in order to provide the information needed for the context activation request(s).
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 9.3 Show PDP address +CGPADDR 9.3.1 Command Syntax Command Possible response(s) +CGPADDR=[, id> [, [+CGPADDR: , [,…]]] [...]] +CGPADDR=? +CGPADDR: (list of defined s) 9.3.2 Description The execution command returns a list of PDP addresses for the specified context identifiers. The test command returns a list of defined s. 9.3.
HUAWEI UMTS M2M Module AT Command Interface Specification Command Confidential Possible response(s) +CGDCONT: (range of supported s), ,,,(list of supported s),(list of supported s) +CGDCONT=? [+CGDCONT: (range of supported s), ,,,(list of supported s), (list of supported s)[...]]OK 9.4.2 Description A group of setting environments indexed by are stored locally.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential : A numerical value, controlling the compression of PDP header. 0 No compression. 1 Compression. If no is included, it is equivalent to the effect that the is 0. 9.4.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential +CGDCONT:1,”IP”,”vcol.com”,””,0,0 OK Note: The PDP setting environment whose =16 in the MS has been cleared. 9.5 DS traffic reset %DSFLOWCLR 9.5.1 Command Syntax Command %DSFLOWCLR Possible response(s) OK 9.5.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 0000000000000000-FFFFFFFFFFFFFFFF, 16-digit hexadecimal number, indicating the last DS transmitting traffic, unit: byte. : 0000000000000000-FFFFFFFFFFFFFFFF, 16-digit hexadecimal number, indicating the last DS receiving traffic, unit: byte. : 00000000-FFFFFFFF, 8-digit hexadecimal number, indicating the DS accumulated connection time, unit: s.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 00000000-FFFFFFFF, 8-digit hexadecimal number, indicating the current receiving rate, unit: bps. : 0000000000000000-FFFFFFFFFFFFFFFF, 16-digit hexadecimal number, indicating the current DS transmitting traffic, unit: byte. : 0000000000000000-FFFFFFFFFFFFFFFF, 16-digit hexadecimal number, indicating the current DS receiving traffic, unit: byte.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential < sec_dns_address >: string type,secondary DNS IP 10.2 Open TCP/UDP link %IPOPEN 10.2.1 Command Syntax Command Possible response(s) %IPOPEN=,[, OK [,[,ERROR l_port>]]] %IPOPEN:,,[,[,]] [%IPOPEN:,,[,[,]] [...
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Command Possible response(s) %IPLISTEN=,OK ort> ERROR %IPLISTEN:,,OK % IPLISTEN:(range of supported ),(list of supported ),(range of %IPLISTEN=? supported )OK 10.3.2 Description This command is used to enable listening fuction.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 10.5.1 Command Syntax Command Possible response(s) %IPGETDATA:,,[OK] > %IPGETDATA:, [%IPGETDATA: %IPGETDATA? , [...
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 10.7 Close TCP/UDP link %IPCLOSE 10.7.1 Command Syntax Command %IPCLOSE=[] Possible response(s) OK %IPCLOSE:, ,,,OK %IPCLOSE:(range of )OK %IPCLOSE? %IPCLOSE=? 10.7.2 Description This command is used to close a TCP/UDP link or exit TCP/UDP function.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Note: %IPENTRANS command will set current link into transparent mode. Before this command, please make sure that first data packet is sent with %IPSEND command, which set current link available. 11 Overall Design Constraints 11.1 Standards Compliance AT command standards. For details, see the protocols 27.007, 27.005 and V0025-TE. 11.2 Hardware Limitations 11.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential 16 Appendixes 16.1 Appendix 1 AT Command Description 16.1.1 Basic Commands The format of a basic command is: [] Where, is a single letter (A-Z) or a “&” plus a single letter, and is a decimal number composed of one or more digits. The 0s at the head of will be ignored. If a basic command that can carry carries no , the value is 0 by default.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential indicates multiple parameters, separated by “,” in the middle. For the parameters that have a default value, they can be omitted and substitute the default value. If all the parameters are omitted, the “=” behind should be omitted too. If is not identified, it indicates that this command does not exist, and the information “COMMAND NOT SUPPORT” will be returned.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential depending on the abort attribute of the command. Each AT command has the abort attribute. This attribute is a two-option choice. Namely, the command either supports abort or does not support abort. The commands that support abort include some basic commands and the EXECUTION command of action command. These commands do not accept any abort request within 125ms after being issued.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential %DTMF= 30 %CPBS= 9 4 1 %CPBR= 9 4 6 1 %CPBW = 9 4 6 1 %SPN= 10 13 11 10 14 1 26 27 30 31 32 100 134 257 258 259 260 261 262 263 264 +CLCK= 25 +CCWA= 17 18 19 20 21 22 23 24 25 26 +CCFC= 17 18 19 20 21 22 23 24 25 26 +CUSD= 17 18 19 20 21 22 23 24 25 26 +COPS= 27 %DTMF= 16 %CPBR= %CPBW = 12 15 16 12 %SPN 12 65280 +CHLD= 33 %DTMF= 33 65281 38 65282 65823 34,
HUAWEI UMTS M2M Module AT Command Interface Specification 12 Unknown error 13 Phonebook storage is full 14 Too long text string 15 Too long number 16 Invalid characters included in the number 17 Network timeout 18 Temporary disorder of service options 19 Rejected by network 20 Retry operations caused by system error or operation busy 21 Call deviated to the incorrect number 22 Call deviated to the user’s own number 23 User unidentifiable 24 Service resources nonexistent 25 Unknow
HUAWEI UMTS M2M Module AT Command Interface Specification 15 SIM wrong 16 incorrect password 17 SIM PIN2 required 18 SIM PUK2 required 20 memory full 21 invalid index 22 not found 23 memory failure 24 text string too long 26 dial string too long 27 invalid characters in dial string 30 no network service 31 network timeout 32 network not allowed - emergency calls only 100 unknown 134 service option temporarily out of order (#34) 257 network rejected supervision request 258
HUAWEI UMTS M2M Module AT Command Interface Specification +CNMA 5 +CPMS 3 +CSCA +CMGS Confidential 1 2 16 6 7 8 9 10 6 7 8 9 13 13 3 5 6 7 8 9 +CMGW 3 5 6 7 8 9 10 +CMGL 3 6 7 8 9 10 +CMGR 3 6 7 8 9 10 14 15 12 11 Note: 1 RP layer error 2 TP layer error 3 Some other applications leave SMS interface reserved 4 Operation not supported.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential BUSY 7 Opposite party busy NO ANSWER 8 Connection completion timeout, no answer +CME ERROR: Error type is specified by the parameter +CMS ERROR: SMS-related error COMMAND SUPPORT NOT Numbering mode is not Issued command supported supported is not TOO MANY Numbering mode is not Too many parameters in the PARAMETERS supported issued command 16.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential Description of initial value +CLIP is 0 +CMUT is 0 +CLVL is read from NV. +CSSN is 0, is 0 %PROTSEL is 0 +CMMS is 2 %CURC is 0x00000003 16.6 Appendix 7 Examples of Show Mode Query Mode:We can use “AT%SYSINFO?” to acquire system server domain and system mode.
HUAWEI UMTS M2M Module AT Command Interface Specification Confidential List of reference: [1] 3GPP protocol 27.005-3d0 [2] 3GPP protocol 27.007-320 [3] ITU-T Recommendation V.25 ter V0025-TE.