Copyright © 2008 Huawei Technologies Co., Ltd. All Rights Reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The information in this document is subject to change without notice.
Table of Contents Getting to Know the UMG181....................................................................................................... 1 PC Requirements ........................................................................................................................... 3 Preparing the UMG181.................................................................................................................. 4 Installation Guide.................................................................
Thank you for purchasing Huawei UMG181 HSPA Rotate USB Stick. Note: This manual briefly describes the preparation, the process for installing/uninstalling, and safety precautions for using Huawei UMG181 HSPA Rotate USB Stick (hereinafter referred to as the UMG181). Read the manual before using the UMG181. Getting to Know the UMG181 The following figures show the appearance of the UMG181. The actual device may differ.
n Rotatable USB connector This is where the UMG181 connects to the USB interface of your PC. o USIM/SIM card slot Open the lid to insert the USIM/SIM card in the slot. p RF Output Power Port Connects the RF cable.
q Indicator Indicates the status of the UMG181. Green, blinking twice every 3s: The UMG181 is powered on. Green, blinking once every 3s: The UMG181 is registered to a GSM/GPRS/EDGE network. Blue, blinking once every 3s: The UMG181 is registered to a WCDMA/HSDPA network. Green, always on: The GPRS/EDGE connection is set up. Blue, always on: The WCDMA connection is set up. Cyan, always on: The HSDPA connection is set up. Off: The UMG181 is removed from the PC. \ Micro SD card sl
Preparing the UMG181 1. Remove the back cover of the UMG181. 2. Insert the USIM/SIM card and the micro SD card into the card slots. Make sure that the cards are properly inserted. Note: A micro SD card is an optional accessory and not included with your device. Do not remove the USIM/SIM card and the micro SD card when they are being used. Removing the cards during an operation may damage the cards as well as the device, and data stored on the cards may be corrupted.
Installation Guide The procedure for installing the management program depends on the operating system installed on your PC. The following section takes Windows XP as an example. Connecting the UMG181 with a PC Note: Turn on your PC before connecting the UMG181 with it. Otherwise, the normal installation of the UMG181 may be affected. Method 1: Plug the UMG181 into the USB interface of the PC.
Method 2:connect the UMG181 to a PC using the USB extension cable. Installing the UMG181 Management Program 1. Connect the UMG181 with the PC. 2. The OS automatically detects and recognizes new hardware and starts the installation wizard. Note: If the auto-run program does not respond, find the AutoRun.exe file in the driver path. Then double-click AutoRun.exe to run the program.
3. Follow the prompts of the installation wizard. 4. After the program is installed, the shortcut icon of the management program is displayed on the desktop of your PC. Launching the Management Program After the UMG181 is installed, the management program is launched automatically. Then every time the UMG181 is connected to the PC, the management program is launched automatically. You can also double-click the shortcut icon on the desktop to launch the management program.
Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device. Regulatory Notices UMG181 complies with Parts 15, 22, and 24 of the FCC rules. It has been tested by using a typical PC with a USB port. This USB device must not be located or operated near any other antenna or transmitter.If you use this USB device in any other configuration, the FCC RF Exposure compliance limit can be exceeded.
Acquisitions Regulations (FARs) Section 52.227-19 for civilian agency contracts or any successor regulations. If further government regulations apply, it is your responsibility to ensure compliance with such regulations. * WARNING: This product contains a chemical known to the State of California to cause cancer. * WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
powder). Area indicated with the "Explosives" sign. Area indicated with the "Power off bi-direction wireless equipment" sign. Area where you are generally suggested to stop the engine of a vehicle. Traffic Security Observe local laws and regulations while using the wireless device. To prevent accidents, do not use your wireless device while driving. RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer.
in electrical and electronic equipment Directive 2002/95/EC (RoHS Directive). Laws and Regulations Observance Observe laws and regulations when using your wireless device. Respect the privacy and legal rights of the others. Care and Maintenance It is normal that your wireless device gets hot when you use it. Before you clean or maintain the wireless device, stop all applications and disconnect the wireless device from your PC. Use your wireless device and accessories with care and in clean environment.
Specific Absorption Rate (SAR) THIS USB STICK MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
of safety to give additional protection to the public and to account for any variations in measurements. Exposure to RF Energy Use only the supplied or an approved replacement antenna. Do not touch the antenna unnecessarily when the USB Stick is in use. Do not move the antenna close to, or touching any exposed part of the body when making a call. FCC Statement This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
The USB Stick was tested on all four sides of the unit with the bottom and one side being installed in a laptop. The top and other side was on a USB extension cable. The device can be used in notebook computers with substantially similar physical dimensions, construction, and electrical and RF characteristics. If this USB Stick is intended for use in any other portable device, you are responsible for separate approval to satisfy the SAR requirements of Part 2.1093 of FCC rules.
12 MONTH LIMITED WARRANTY Personal Communications Devices, LLC.
When sending your wireless device to Personal Communications Devices for repair or service, please note that any personal data or software stored on the device may be inadvertently erased or altered. Therefore, we strongly recommend you make a back up copy of all data and software contained on your device before submitting it for repair or service. This includes all contact lists, downloads (i.e. third-party software or applications, games, and graphics), and any other data added to your device.
No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states or provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitation or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.
